[hylafax-users] Problems receiving faxes with Creatix SG2834 Turbo

[Meinhard Schneider <meini@xxxxxxxxx>]

Hi,

I found an old thread [1] on this problem, but no solution:
I am trying to receive faxes with an old Creatix SG2834 Turbo modem.
Sending faxes works fine, but receiving will cause the sender to report
an error, even HylaFAX said that there was no error and the fax document
is complete. I attached a piece of log.

Is there any solution for this problem or should I get an other modem?

Thanks in advance
Meinhard

[1] http://www.hylafax.org/archive/1998-12/msg00129.php

Jun 03 11:25:24.95: [12207]: SESSION BEGIN 000000009 4956131690183
Jun 03 11:25:24.95: [12207]: HylaFAX (tm) Version 4.2.5
Jun 03 11:25:24.95: [12207]: <-- [4:ATA\r]
Jun 03 11:25:32.90: [12207]: --> [5:+FCON]
Jun 03 11:25:32.90: [12207]: DELAY 10 ms
Jun 03 11:25:32.91: [12207]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS1'
Jun 03 11:25:32.91: [12207]: RECV FAX: begin
Jun 03 11:25:34.51: [12207]: --> [29:+FTSI: "     +49 561 9402785"]
Jun 03 11:25:34.51: [12207]: REMOTE TSI "+49 561 9402785"
Jun 03 11:25:34.78: [12207]: --> [22:+FDCS: 1,5,0,2,1,0,0,1]
Jun 03 11:25:34.78: [12207]: REMOTE wants 14400 bit/s
Jun 03 11:25:34.78: [12207]: REMOTE wants A4 page width (215 mm)
Jun 03 11:25:34.78: [12207]: REMOTE wants unlimited page length
Jun 03 11:25:34.78: [12207]: REMOTE wants 7.7 line/mm
Jun 03 11:25:34.78: [12207]: REMOTE wants 2-D MR
Jun 03 11:25:34.89: [12207]: --> [2:OK]
Jun 03 11:25:34.89: [12207]: <-- [7:AT+FDR\r]
Jun 03 11:25:37.84: [12207]: --> [5:+FCFR]
Jun 03 11:25:39.94: [12207]: --> [22:+FDCS: 1,5,0,2,1,0,0,1]
Jun 03 11:25:39.94: [12207]: REMOTE wants 14400 bit/s
Jun 03 11:25:39.94: [12207]: REMOTE wants A4 page width (215 mm)
Jun 03 11:25:39.94: [12207]: REMOTE wants unlimited page length
Jun 03 11:25:39.94: [12207]: REMOTE wants 7.7 line/mm
Jun 03 11:25:39.94: [12207]: REMOTE wants 2-D MR
Jun 03 11:25:39.95: [12207]: --> [7:CONNECT]
Jun 03 11:25:39.95: [12207]: RECV: begin page
Jun 03 11:25:39.95: [12207]: RECV: send trigger 022
Jun 03 11:25:39.95: [12207]: <-- data [1]
Jun 03 11:25:39.95: [12207]: Copy quality checking performed by host
Jun 03 11:25:59.46: [12207]: RECV: 2292 total lines, 0 bad lines, 0 consecutive bad lines
Jun 03 11:25:59.47: [12207]: --> [17:+FPTS: 2,2219,0,0]
Jun 03 11:26:00.70: [12207]: --> [7:+FET: 2]
Jun 03 11:26:00.70: [12207]: RECV recv EOP (no more pages or documents)
Jun 03 11:26:00.81: [12207]: --> [2:OK]
Jun 03 11:26:00.81: [12207]: RECV send MCF (message confirmation)
Jun 03 11:26:00.81: [12207]: <-- [7:AT+FDR\r]
Jun 03 11:26:00.81: [12207]: RECV FAX (000000009): recvq/fax000000004.tif from +49 561 9402785, route to <unspecified>, 1 pages in 0:28
Jun 03 11:26:00.81: [12207]: RECV FAX (000000009): from +49 561 9402785, page 1 in 0:27, INF, 7.7 line/mm, 2-D MR, 14400 bit/s
Jun 03 11:26:03.71: [12207]: --> [8:+FHNG: 0]
Jun 03 11:26:03.71: [12207]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Jun 03 11:26:03.71: [12207]: RECV FAX: bin/faxrcvd "recvq/fax000000004.tif" "ttyS1" "000000009" ""
Jun 03 11:26:03.71: [12207]: RECV FAX: end
Jun 03 11:26:03.72: [12207]: SESSION END