Re: [hylafax-users] High failure rate on sending

[Daniel Hillhouse <daniel.hillhouse@xxxxxxxxxxxxxxxx>]

Lee,

Thanks for your help with this issue. It did turn out to be the modem. I 
bought a new one today and it successfully sent to all of the numbers 
I'd previously had issues with.

Thanks again.
Daniel.

Lee Howard wrote:

> Daniel,
>
> At this point I would start to consider the modem hardware/firmware 
> suspect.
>
> There may be some kind of initialization that would work around the 
> problem, but that may require you to contact and work with the 
> manufacturer.
>
> Thanks,
>
> Lee.
>
>
> Daniel Hillhouse wrote:
>
> > Thanks Lee.
> >
> > I was using xonxoff so I changed that to rtscts but it still had 
> > errors. This time it didn't resubmit those sections. Here is the 
> > bottom of the new log. Everything went fine up to frame 255.
> >
> > ...
> > Nov 04 15:46:04.22: [ 9837]: SEND send frame number 255
> > Nov 04 15:46:04.22: [ 9837]: DELAY 200 ms
> > Nov 04 15:46:04.41: [ 9837]: <-- [11:AT+FTM=146\r]
> > Nov 04 15:46:04.91: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:46:43.30: [ 9837]: --> [2:OK]
> > Nov 04 15:46:43.30: [ 9837]: <-- [9:AT+FTS=9\r]
> > Nov 04 15:46:43.32: [ 9837]: --> [2:OK]
> > Nov 04 15:46:43.32: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:46:43.37: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:46:44.79: [ 9837]: --> [2:OK]
> > Nov 04 15:46:44.79: [ 9837]: SEND send PPS (partial page signal)
> > Nov 04 15:46:44.79: [ 9837]: SEND send NULL (more blocks, same page)
> > Nov 04 15:46:44.79: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:46:45.47: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:46:49.72: [ 9837]: --> [2:OK]
> > Nov 04 15:46:49.72: [ 9837]: HDLC frame too short (0 bytes)
> > Nov 04 15:46:49.72: [ 9837]: <-- [9:AT+FRS=7\r]
> > Nov 04 15:46:49.74: [ 9837]: --> [2:OK]
> > Nov 04 15:46:49.74: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:46:49.79: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:46:51.11: [ 9837]: --> [2:OK]
> > Nov 04 15:46:51.11: [ 9837]: SEND send CRP (command repeat)
> > Nov 04 15:46:51.11: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:46:54.21: [ 9837]: --> [0:]
> > Nov 04 15:46:54.21: [ 9837]: MODEM <Empty line>
> > Nov 04 15:46:54.41: [ 9837]: MODEM <Timeout>
> > Nov 04 15:46:54.41: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:46:54.46: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:46:55.88: [ 9837]: --> [2:OK]
> > Nov 04 15:46:55.88: [ 9837]: SEND send PPS (partial page signal)
> > Nov 04 15:46:55.88: [ 9837]: SEND send NULL (more blocks, same page)
> > Nov 04 15:46:55.88: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:46:56.54: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:00.82: [ 9837]: --> [2:OK]
> > Nov 04 15:47:00.82: [ 9837]: HDLC frame too short (0 bytes)
> > Nov 04 15:47:00.82: [ 9837]: <-- [9:AT+FRS=7\r]
> > Nov 04 15:47:00.84: [ 9837]: --> [2:OK]
> > Nov 04 15:47:00.84: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:47:00.89: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:02.21: [ 9837]: --> [2:OK]
> > Nov 04 15:47:02.21: [ 9837]: SEND send CRP (command repeat)
> > Nov 04 15:47:02.21: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:47:05.31: [ 9837]: --> [0:]
> > Nov 04 15:47:05.31: [ 9837]: MODEM <Empty line>
> > Nov 04 15:47:05.51: [ 9837]: MODEM <Timeout>
> > Nov 04 15:47:05.51: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:47:05.56: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:06.98: [ 9837]: --> [2:OK]
> > Nov 04 15:47:06.98: [ 9837]: SEND send PPS (partial page signal)
> > Nov 04 15:47:06.98: [ 9837]: SEND send NULL (more blocks, same page)
> > Nov 04 15:47:06.98: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:47:07.66: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:09.73: [ 9837]: --> [2:OK]
> > Nov 04 15:47:09.73: [ 9837]: HDLC frame with bad control field 0x20
> > Nov 04 15:47:09.73: [ 9837]: <-- [9:AT+FRS=7\r]
> > Nov 04 15:47:09.75: [ 9837]: --> [2:OK]
> > Nov 04 15:47:09.75: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:47:09.80: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:11.11: [ 9837]: --> [2:OK]
> > Nov 04 15:47:11.11: [ 9837]: SEND send CRP (command repeat)
> > Nov 04 15:47:11.11: [ 9837]: <-- [9:AT+FRH=3\r]
> > Nov 04 15:47:14.21: [ 9837]: --> [0:]
> > Nov 04 15:47:14.21: [ 9837]: MODEM <Empty line>
> > Nov 04 15:47:14.41: [ 9837]: MODEM <Timeout>
> > Nov 04 15:47:14.41: [ 9837]: No response to PPS repeated 3 times.
> > Nov 04 15:47:14.41: [ 9837]: SEND end page
> > Nov 04 15:47:14.41: [ 9837]: <-- [9:AT+FTH=3\r]
> > Nov 04 15:47:14.46: [ 9837]: --> [7:CONNECT]
> > Nov 04 15:47:15.78: [ 9837]: --> [2:OK]
> > Nov 04 15:47:15.78: [ 9837]: SEND FAILED: JOB 367 
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*