HylaFAX The world's most advanced open source fax server |
Most USR modems have dip switches located on the back or bottom of the modem, one of which disables auto-answer manually. Check that first. If there isn't a label on the modem describing each switches function you should be able to find out the info from USRs website (http://www.usr.com/) Laker --- Mark <mark@xxxxxxxxxxxxx> wrote: > Hello List, > > I've been browsing the archives and googling all > over the place, I can't > get faxgetty (Better said: Hylafax) to receive an > incoming call. > > It won't pick up the modem. > > But when I type faxanswer ttyS0, it will pick up and > receive the fax. > But it will not do so on it's own. > > Everything is running I think: > ams-it:/etc/hylafax# ps ax | grep fax > 20107 ? Ss 0:00 /usr/sbin/faxq > 20109 ? Ss 0:00 /usr/sbin/hfaxd -i 4559 > 20120 pts/1 S 0:00 /usr/sbin/faxgetty ttyS0 > > And I'm also able to send faxes. It just wont > receive (not even pickup > the line) them. > > # > # > CountryCode: 31 > AreaCode: 020 > FAXNumber: +31.020.850[private] > LongDistancePrefix: 0 > InternationalPrefix: 0 > DialStringRules: etc/dialrules > ServerTracing: 1 > SessionTracing: 11 > RecvFileMode: 0666 > LogFileMode: 0666 > DeviceMode: 0666 > RingsBeforeAnswer: 1 > SpeakerVolume: off > GettyArgs: "-h %l dx_%s" > LocalIdentifier: "Some company" > TagLineFont: etc/lutRS18.pcf > TagLineFormat: "From %%l|%c|Page %%P of > %%T" > MaxRecvPages: 25 > # > # > # Modem-related stuff: should reflect modem command > interface > # and hardware connection/cabling (e.g. flow > control). > # > ModemType: Class1 # use class > 1 interface > ModemRate: 19200 # rate for > DCE-DTE communication > ModemFlowControl: xonxoff # software > flow control > # > ModemSetupDTRCmd: ATS13=1&D2 # setup so > DTR drop resets modem > ModemSetupDCDCmd: AT&C1 # setup so > DCD reflects carrier > (or not) > ModemNoFlowCmd: AT&H0&I0&R1 # setup > modem for no flow > control > ModemHardFlowCmd: AT&H1&I0&R2 # setup > modem for hardware flow > control > ModemSoftFlowCmd: AT&H2&I2&R1 # setup > modem for software flow > control > ModemResultCodesCmd: ATQ0X4 # enable > result codes > # > ModemMfrQueryCmd: !USR > ModemModelQueryCmd: ATI3 > ModemRevQueryCmd: ATI7 # XXX > returns a multi-line > result > # > # When AT+FCLASS=1 is issued the modem automatically > switches > # to software flow control; these parameters let the > fax software > # reset flow control as needed after entering Class > 1. > # > Class1NFLOCmd: AT&H0&I0&R1 # setup > modem for no flow > control > Class1HFLOCmd: AT&H1&I0&R2 # setup > modem for hardware flow > control > Class1SFLOCmd: "" # modem does > this automatically > # > # This should resolve "DIS/DTC received 3 times" > errors: > # > Class1ResponseWaitCmd: AT+FRS=1 # wait after > sending TCF for > response > # > # The remainder of this configuration is included so > that the > # modem "idles" in Class 0 while not sending or > receiving facsimile. > # > ModemSetupAACmd: AT+FCLASS=0 # leave > modem idling in class 0 > ModemAnswerCmd: AT+FCLASS=1A # answer in > Class 1 > # > # Disables the reporting of bad frames by the modem. > This > # overcomes a firmware problem in the x2 and V90 > Sportsters. > # It is not necessary for the Courier modem. > # > Class2NRCmd: AT+FNR=1,1,1,0 > > And hyla config: > ams-it:/etc/hylafax# cat ./hfaxd.conf > # > # HylaFAX Client-Server Protocol Configuration. > # > # Consult hfaxd(1M) for information on the contents > # of this file. Note that pathnames specified in > # this file are relative to the root of the spooling > # area because hfaxd uses chroot to confine client > # accesses to the server's filesystem. > # > LogFacility: daemon # syslog > facility (want this > 1st)) > ServerTracing: 0x001 # just > server operation > #IdleTimeout: 900 # initial > client idle timeout > (secs) > #MaxIdleTimeout: 7200 # max client > idle timeout (secs) > #MaxLoginAttempts: 5 # max # > login attempts before > disconnect#MaxAdminAttempts: 5 # > max # admin attempts > before disconnect#MaxConsecutiveBadCmds: 10 > # max # invalid > cmds before disconnect > #FaxContact: FaxMaster # who gets > questions/complaints > #AdminGroup: faxadmin # which user > group is admin > (when using PAM) > #UserAccessFile: "/etc/hosts.hfaxd" # > user+host access > control file > #ShutdownFile: "/etc/shutdown" # server > shutdown control > filename > #XferLogFile: "/etc/clientlog" # > for logging client > file transfers > #FaxQFIFOName: "/FIFO" # FIFO name > for talking to faxq > process > # > # The default format used to return job status > queries. > # Note that clients can override this with JOBFMT. > # > #JobFmt: "%-3j %3i %1a %6.6o %-12.12e > %5P %5D %7z %.25s" > # > # The default format used to return recvq status > queries. > # Note that clients can override this with RCVFMT. > # > #RcvFmt: "%-7m %4p%1z %-8.8o %14.14s > %7t %f" > # > # The default format used to return modem status > queries. > # Note that clients can override this with MODEMFMT. > # > #ModemFmt: "Modem %m (%n): %s" > # > # The default format used to return file-oriented > # directory listings. > # Note that clients can override this with FILEFMT. > # > #FileFmt: "%-7p %3l %8o %8s %-12.12m > %.48f" > > # > # SNPP-specific parameters. > # > #MaxMsgLength: 128 # max pager > message length > #PagerIDMapFile: "/etc/pagermap" # file with > pager === message truncated === __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*