 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problems to receive a facsimile
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Problems to receive a facsimile
- From: Frank Geschner <fgeschner@xxxxxxx>
- Date: Fri, 05 Aug 2005 12:39:22 +0200
Hello all, I am using hylafax 4.2.1. Sending facsimiles works fine but I can not reveive any facsimiles. At the moment I have no idea what is the problem. The following lines document the behaviour. Can anybody help me? At the end of this posting I have added the content of the file config.ttyS1 Remarks: I only changed my number and the TSI of the sender in this posting. Thanks in advance! Frank Aug 05 12:31:26.46: [ 3517]: SESSION BEGIN 000000008 4937209XXXX Aug 05 12:31:26.46: [ 3517]: HylaFAX (tm) Version 4.2.1 Aug 05 12:31:26.46: [ 3517]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled Aug 05 12:31:26.47: [ 3517]: <-- [4:ATA\r] Aug 05 12:31:29.47: [ 3517]: --> [7:CONNECT] Aug 05 12:31:29.47: [ 3517]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1' Aug 05 12:31:29.47: [ 3517]: MODEM input buffering enabled Aug 05 12:31:29.47: [ 3517]: RECV FAX: begin Aug 05 12:31:29.48: [ 3517]: MODEM input buffering disabled Aug 05 12:31:29.48: [ 3517]: <-- data [32] Aug 05 12:31:29.48: [ 3517]: <-- data [2] Aug 05 12:31:31.35: [ 3517]: --> [7:CONNECT] Aug 05 12:31:31.35: [ 3517]: <-- data [23] Aug 05 12:31:31.35: [ 3517]: <-- data [2] Aug 05 12:31:32.13: [ 3517]: --> [7:CONNECT] Aug 05 12:31:32.13: [ 3517]: <-- data [10] Aug 05 12:31:32.13: [ 3517]: <-- data [2] Aug 05 12:31:32.54: [ 3517]: --> [2:OK] Aug 05 12:31:32.54: [ 3517]: <-- [9:AT+FRH=3\r] Aug 05 12:31:33.17: [ 3517]: --> [7:CONNECT] Aug 05 12:31:34.96: [ 3517]: --> [2:OK] Aug 05 12:31:34.96: [ 3517]: REMOTE TSI "YYYY" Aug 05 12:31:34.96: [ 3517]: <-- [9:AT+FRH=3\r] Aug 05 12:31:35.00: [ 3517]: --> [7:CONNECT] Aug 05 12:31:35.36: [ 3517]: --> [2:OK] Aug 05 12:31:35.36: [ 3517]: REMOTE wants 14400 bit/s Aug 05 12:31:35.36: [ 3517]: REMOTE wants A4 page width (215 mm) Aug 05 12:31:35.36: [ 3517]: REMOTE wants unlimited page length Aug 05 12:31:35.36: [ 3517]: REMOTE wants 7.7 line/mm Aug 05 12:31:35.36: [ 3517]: REMOTE wants 1-D MH Aug 05 12:31:35.36: [ 3517]: RECV training at v.17 14400 bit/s Aug 05 12:31:35.36: [ 3517]: MODEM set XON/XOFF/DRAIN: input ignored, output generated Aug 05 12:31:35.36: [ 3517]: <-- [11:AT+FRM=145\r] Aug 05 12:31:37.11: [ 3517]: --> [7:CONNECT] Aug 05 12:31:38.61: [ 3517]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled Aug 05 12:31:38.61: [ 3517]: RECV: TCF 2688 bytes, 0% non-zero, 2675 zero-run Aug 05 12:31:38.62: [ 3517]: --> [10:NO CARRIER] Aug 05 12:31:38.62: [ 3517]: DELAY 75 ms Aug 05 12:31:38.70: [ 3517]: TRAINING succeeded Aug 05 12:31:38.71: [ 3517]: <-- [9:AT+FTH=3\r] Aug 05 12:31:38.74: [ 3517]: --> [7:CONNECT] Aug 05 12:31:38.74: [ 3517]: <-- data [3] Aug 05 12:31:38.74: [ 3517]: <-- data [2] Aug 05 12:31:39.95: [ 3517]: --> [2:OK] Aug 05 12:31:39.95: [ 3517]: MODEM input buffering enabled Aug 05 12:31:39.95: [ 3517]: MODEM set XON/XOFF/FLUSH: input ignored, output generated Aug 05 12:31:39.95: [ 3517]: <-- [11:AT+FRM=146\r] Aug 05 12:31:40.79: [ 3517]: --> [7:CONNECT] Aug 05 12:31:40.79: [ 3517]: RECV: begin page Aug 05 12:31:43.80: [ 3517]: RECV: 378 total lines, 0 bad lines, 0 consecutive bad lines Aug 05 12:31:43.80: [ 3517]: RECV: end page Aug 05 12:31:43.80: [ 3517]: --> [10:NO CARRIER] Aug 05 12:31:43.80: [ 3517]: <-- [9:AT+FRH=3\r] Aug 05 12:31:43.94: [ 3517]: --> [7:CONNECT] Aug 05 12:31:45.08: [ 3517]: --> [2:OK] Aug 05 12:31:45.08: [ 3517]: RECV recv EOP (no more pages or documents) Aug 05 12:31:45.08: [ 3517]: <-- [9:AT+FRS=7\r] Aug 05 12:32:15.08: [ 3517]: MODEM TIMEOUT: reading line from modem Aug 05 12:32:15.08: [ 3517]: MODEM <Timeout> Aug 05 12:32:15.09: [ 3517]: RECV FAX: Failure to receive silence. Aug 05 12:32:15.09: [ 3517]: <-- [9:AT+FTH=3\r] Aug 05 12:32:15.09: [ 3517]: RECV FAX (000000008): recvq/fax000000007.tif from YYYY, route to <unspecified>, 0 pages in 0:46 Aug 05 12:32:15.23: [ 3517]: --> [2:OK] Aug 05 12:32:15.23: [ 3517]: MODEM input buffering enabled Aug 05 12:32:15.23: [ 3517]: RECV FAX (000000008): session with AKW AUTOMOBILE GMBH terminated abnormally: Failure to receive silence. Aug 05 12:32:15.24: [ 3517]: RECV FAX: bin/faxrcvd "recvq/fax000000007.tif" "ttyS1" "000000008" "Failure to receive silence." "" "" Aug 05 12:32:15.24: [ 3517]: RECV FAX: end Aug 05 12:32:15.26: [ 3517]: SESSION END ======================================================================== # $Id: class1,v 1.14 2004/04/19 18:44:46 lhoward Exp $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Generic Class 1 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 49 AreaCode: 37209 FAXNumber: +49.37209.XXXX LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 527 SessionTracing: 527 RecvFileMode: 0666 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 6 SpeakerVolume: 3 GettyArgs: "-r -b -s %s %l" LocalIdentifier: "Geschner" TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint #ModemRate: 19200 # rate for DCE-DTE communication #ModemFlowControl: xonxoff # XON/XOFF flow control assumed # #ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem #ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier #GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data # # We can append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s # T for tone dialing # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # #ModemResetCmds: "" # stuff to do when modem is reset #ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemSoftResetCmdDelay: 3000 # pause after soft reset #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP Class1MsgRecvHackCmd: "" # command to avoid +FCERROR before image Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response Class1SendMsgDelay: 200 # 75ms delay after training Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Problems to receive a facsimile
- From: Lee Howard
- Re: [hylafax-users] Problems to receive a facsimile
- Prev by Date: Re: [hylafax-users] Lost Documents problem
- Next by Date: [hylafax-users] fax header not being printed
- Previous by thread: Re: [hylafax-users] Lost Documents problem
- Next by thread: Re: [hylafax-users] Problems to receive a facsimile
- Index(es):
Project hosted by iFAX Solutions