Re: [hylafax-users] slmodem 2800 cannot receive fax

[Sipho Mothobi <Sipho.Mothobi@xxxxxxxxx>]

hi,

Have you checked slmodem log ?

Make a call to that line and tail the
log it might be helpfull.

razidan <razidan@xxxxxxxxxxxxxxx>
Sent by: hylafax-users-bounce@xxxxxxxxxxx

30/06/2005 11:01

To	hylafax-users@xxxxxxxxxxx
cc
Subject	[hylafax-users] slmodem 2800 cannot receive fax

hello

im using  Smartlink pci modem (sl2800) and configure hylafax to use
that  
modem at /dev/ttySL0.

when i tested it, hylafax can send fax but it can't receive any. Nothing
 is 
registered in syslog when someone is trying to send me a fax.

This is my configuration file

************************************************************************
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:                
                 xx
AreaCode:                
                 x
FAXNumber:                
                 xxxxxxxxxx
LongDistancePrefix:              
  1
InternationalPrefix:            
    00
DialStringRules:              
  etc/dialrules
ServerTracing:              
               
   63
SessionTracing:              
               
   63
RecvFileMode:              
               
   0644
LogFileMode:                
                 0644
DeviceMode:                
                 0644
RingsBeforeAnswer:              
  2
SpeakerVolume:              
               
   medium
GettyArgs:                
                 "-h
%l dx_%s"
LocalIdentifier:              
  "NothingSetup"
TagLineFont:                
                 etc/lutRS18.pcf
TagLineFormat:              
               
   "From %%l|%c|Page %%P of %%T"
MaxRecvPages:              
               
   25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:                
                 Class1
               
                 #
use this to supply a hint
ModemRate:                
                 19200
               
                 #
rate for DCE-DTE communication
#ModemFlowControl:              
  xonxoff            
               
     # XON/XOFF flow control assumed -*
#
#ModemSetupDTRCmd:              
  AT&D2            
               
     # setup so DTR drop resets modem -*
#ModemSetupDCDCmd:              
  AT&C1            
               
     # setup so DCD follows carrier -*
#GettyArgs:                
                 "-h
%l dx_%s"              
  # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:              
               
   ATDT%s          
               
       # T for tone dialing -*
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:              
               
   ""          
               
       # stuff to do when modem is reset -*
ModemAnswerCmd:              
               
   ATA            
               
     # use this to answer phone
#ModemNoFlowCmd:              
               
   AT&K          
               
       # disable flow control cmd -*
#ModemHardFlowCmd:              
  AT&K3            
               
     # hardware flow control cmd -*
#ModemSoftFlowCmd:              
  AT&K4            
               
     # software flow control cmd -*
ModemNoAutoAnswerCmd:            
    ATS0=0          
               
       # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:              
  "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"  # -*
#ModemEchoOffCmd:              
  ATE0              
               
   # disable command echo -*
#ModemVerboseResultsCmd:            
    ATV1            
               
     # enable verbose command results -*
#ModemResultCodesCmd:            
    ATQ0            
               
     # enable result codes -*
#ModemOnHookCmd:              
               
   ATH0            
               
     # place phone on hook (hangup) -*
#ModemSoftResetCmd:              
  ATZ              
               
   # do soft reset of modem -*
#ModemSoftResetCmdDelay:            
    3000            
    # pause after soft reset -*
#ModemWaitTimeCmd:              
  ATS7=60            
               
     # wait 60 seconds for carrier -*
#ModemCommaPauseTimeCmd:            
    ATS8=2          
               
       # comma pause time is 2 seconds -*
#ModemRecvFillOrder:            
    LSB2MSB          
               
       # bit order of received facsimile -*
#ModemSendFillOrder:            
    LSB2MSB          
               
       # bit order modem expects for transmit
-*
#
Class1Cmd:                
                 AT+FCLASS=1
               
# command to enter class 1
Class1PPMWaitCmd:              
  AT+FTS=7            
    # command to stop and wait before PPM
Class1TCFWaitCmd:              
  AT+FTS=7            
    # command to stop and wait before TCF
Class1EOPWaitCmd:              
  AT+FTS=9            
    # command to stop and wait before EOP
Class1MsgRecvHackCmd:            
    ""        
        # command to avoid +FCERROR before
image
Class1TCFResponseDelay:            
    75            
               
     # 75ms delay between recv TCF & response
Class1SendMsgDelay:              
  200              
               
   # 75ms delay after training
Class1SwitchingCmd:              
  AT+FRS=7            
    # silence between HDLC recv and trans
Class1TrainingRecovery:            
    1500            
               
     # 1.5sec delay after training failure
Class1RecvAbortOK:              
  200              
               
   # wait 200ms for abort response
Class1FrameOverhead:            
    4            
               
     # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:            
    40000          
               
       # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:            
    10            
               
     # max 10% of data may be non-zero
Class1TCFMinRun:              
  1000              
               
   # min run is 2/3rds of TCF duration

pls help

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*

---

This e-mail is subject to a disclaimer, available at
http://www.rmb.co.za/web/elements.nsf/online/disclaimer.php