[hylafax-users] slmodem 2800 cannot receive fax

[razidan <razidan@xxxxxxxxxxxxxxx>]

hello

im using  Smartlink pci modem (sl2800) and configure hylafax to use that  
modem at /dev/ttySL0.

when i tested it, hylafax can send fax but it can't receive any. Nothing  is 
registered in syslog when someone is trying to send me a fax.

This is my configuration file

************************************************************************
# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		xx
AreaCode:		x
FAXNumber:		xxxxxxxxxx
LongDistancePrefix:	1
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		63
SessionTracing:		63
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0644
RingsBeforeAnswer:	2
SpeakerVolume:		medium
GettyArgs:		"-h %l dx_%s"
LocalIdentifier:	"NothingSetup"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
ModemRate:		19200		# rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed -*
#
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem -*
#ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier -*
#GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s		# T for tone dialing -*
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is reset -*
ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd -*
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd -*
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd -*
ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"  # -*
#ModemEchoOffCmd:	ATE0		# disable command echo -*
#ModemVerboseResultsCmd:	ATV1		# enable verbose command results -*
#ModemResultCodesCmd:	ATQ0		# enable result codes -*
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup) -*
#ModemSoftResetCmd:	ATZ		# do soft reset of modem -*
#ModemSoftResetCmdDelay:	3000	# pause after soft reset -*
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier -*
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2 seconds -*
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile -*
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for transmit -*
#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait before PPM
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait before TCF
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait before EOP
Class1MsgRecvHackCmd:	""	# command to avoid +FCERROR before image
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF & response
Class1SendMsgDelay:	200		# 75ms delay after training
Class1SwitchingCmd:	AT+FRS=7	# silence between HDLC recv and trans
Class1TrainingRecovery:	1500		# 1.5sec delay after training failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration

pls help

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*