[hylafax-users] Missing EOL after 5 seconds (section 3.2/T.4)

["Nestor A. Diaz L." <nestor@xxxxxxxxxxxxxxx>]

Hello Everybody,

I have installed hylafax almost a year ago on a server, and it was working
ok, on Debian "Testing" Sarge, however i decide to upgrade the whole
system to the stable release using apt-get, and hylafax sudently decide to
not work again, because it show the following message on every fax it
tries to recieve:

Missing EOL after 5 seconds (section 3.2/T.4)

The modem is a Boca 14.400 bps RC144DPi Rev CA V1.410-AS29

I will like to stick to class2 because this fax supports adaptative answer
so nice, but currently fax is not working.

Any ideas ?

The configuration is the same (config.ttyS0):

CountryCode:            57
AreaCode:               1
FAXNumber:              123456
LongDistancePrefix:     09
InternationalPrefix:    009
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-r -b -s %s %l"
LocalIdentifier:        "XXXXXXXXXX"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              19200
ModemFlowControl:       rtscts          # default
ModemWaitForConnect:    yes             # wait for CONNECT on answer
#
#ModemResetCmds:        AT&F2           # what you want for a Supra
ModemNoFlowCmd:         AT&K            # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to reset
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
ModemSetupAACmd:        AT+FCLASS=0;+FAA=1 # enable in class 0
#ModemSetupAACmd: AT+FAA=1
AdaptiveAnswer:         yes
#
ModemSendFillOrder:     LSB2MSB         # as expected
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
Class2RecvDataTrigger:  "\022"          # a la 2388-B
Class2APQueryCmd:       none            # prevent ERROR
Class2BUGCmd:           none            # prevent ERROR

Here is the error:

    ---- Transcript of session follows ----

Jun 17 09:26:30.18: [ 1288]: SESSION BEGIN 000002830 5714257020
Jun 17 09:26:30.18: [ 1288]: HylaFAX (tm) Version 4.2.1
Jun 17 09:26:30.18: [ 1288]: <-- [4:ATA\r]
Jun 17 09:26:41.69: [ 1288]: --> [3:FAX]
Jun 17 09:26:47.78: [ 1288]: --> [5:+FCON]
Jun 17 09:26:47.78: [ 1288]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jun 17 09:26:47.79: [ 1288]: RECV FAX: begin
Jun 17 09:26:49.43: [ 1288]: --> [29:+FTSI: "824104239           "]
Jun 17 09:26:49.43: [ 1288]: REMOTE TSI "824104239"
Jun 17 09:26:49.75: [ 1288]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 9600 bit/s
Jun 17 09:26:49.75: [ 1288]: REMOTE wants A4 page width (215 mm)
Jun 17 09:26:49.75: [ 1288]: REMOTE wants unlimited page length
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 3.85 line/mm
Jun 17 09:26:49.75: [ 1288]: REMOTE wants 2-D MR
Jun 17 09:26:49.86: [ 1288]: --> [2:OK]
Jun 17 09:26:49.86: [ 1288]: <-- [7:AT+FDR\r]
Jun 17 09:26:51.65: [ 1288]: --> [5:+FCFR]
Jun 17 09:26:53.86: [ 1288]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 9600 bit/s
Jun 17 09:26:53.86: [ 1288]: REMOTE wants A4 page width (215 mm)
Jun 17 09:26:53.86: [ 1288]: REMOTE wants unlimited page length
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 3.85 line/mm
Jun 17 09:26:53.86: [ 1288]: REMOTE wants 2-D MR
Jun 17 09:26:53.86: [ 1288]: --> [7:CONNECT]
Jun 17 09:26:53.86: [ 1288]: RECV: begin page
Jun 17 09:26:53.86: [ 1288]: RECV: send trigger 022
Jun 17 09:26:53.86: [ 1288]: Copy quality checking performed by host
Jun 17 09:28:13.86: [ 1288]: RECV: Missing EOL after 5 seconds
Jun 17 09:28:13.86: [ 1288]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 09:28:13.86: [ 1288]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 09:28:13.86: [ 1288]: <-- [6:AT+FK\r]
Jun 17 09:28:13.86: [ 1288]: RECV FAX (000002830): recvq/fax000002312.tif
from 824104239, route to <unspecified>, 0 pages in 1:26
Jun 17 09:28:13.97: [ 1288]: --> [8:+FHNG: 2]
Jun 17 09:28:13.97: [ 1288]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (code 2)
Jun 17 09:28:13.97: [ 1288]: MODEM Hang up
Jun 17 09:28:13.97: [ 1288]: RECV FAX (000002830): session with 824104239
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 09:28:13.97: [ 1288]: RECV FAX: bin/faxrcvd
"recvq/fax000002312.tif" "ttyS0" "000002830" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 09:28:13.97: [ 1288]: RECV FAX: end
Jun 17 09:28:13.97: [ 1288]: SESSION END


Another one...

    ---- Transcript of session follows ----

Jun 17 11:28:23.39: [ 1274]: SESSION BEGIN 000002833 5714257020
Jun 17 11:28:23.39: [ 1274]: HylaFAX (tm) Version 4.2.1
Jun 17 11:28:23.39: [ 1274]: <-- [4:ATA\r]
Jun 17 11:28:34.79: [ 1274]: --> [3:FAX]
Jun 17 11:28:41.04: [ 1274]: --> [5:+FCON]
Jun 17 11:28:41.04: [ 1274]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jun 17 11:28:41.04: [ 1274]: RECV FAX: begin
Jun 17 11:28:42.70: [ 1274]: --> [29:+FTSI: "             4464770"]
Jun 17 11:28:42.74: [ 1274]: REMOTE TSI "4464770"
Jun 17 11:28:50.43: [ 1274]: --> [29:+FTSI: "             4464770"]
Jun 17 11:28:50.44: [ 1274]: REMOTE TSI "4464770"
Jun 17 11:28:50.77: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 11:28:50.78: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 11:28:50.78: [ 1274]: REMOTE wants unlimited page length
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 11:28:50.78: [ 1274]: REMOTE wants 2-D MR
Jun 17 11:28:50.88: [ 1274]: --> [2:OK]
Jun 17 11:28:50.89: [ 1274]: <-- [7:AT+FDR\r]
Jun 17 11:28:52.67: [ 1274]: --> [5:+FCFR]
Jun 17 11:28:54.75: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 11:28:54.75: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 11:28:54.75: [ 1274]: REMOTE wants unlimited page length
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 11:28:54.75: [ 1274]: REMOTE wants 2-D MR
Jun 17 11:28:54.75: [ 1274]: --> [7:CONNECT]
Jun 17 11:28:54.76: [ 1274]: RECV: begin page
Jun 17 11:28:54.77: [ 1274]: RECV: send trigger 022
Jun 17 11:28:54.77: [ 1274]: Copy quality checking performed by host
Jun 17 11:30:14.82: [ 1274]: RECV: Missing EOL after 5 seconds
Jun 17 11:30:14.83: [ 1274]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 11:30:14.88: [ 1274]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 11:30:14.88: [ 1274]: <-- [6:AT+FK\r]
Jun 17 11:30:14.93: [ 1274]: RECV FAX (000002833): recvq/fax000002314.tif
from 4464770, route to <unspecified>, 0 pages in 1:33
Jun 17 11:30:14.98: [ 1274]: --> [8:+FHNG: 2]
Jun 17 11:30:14.98: [ 1274]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (code 2)
Jun 17 11:30:14.98: [ 1274]: MODEM Hang up
Jun 17 11:30:15.01: [ 1274]: RECV FAX (000002833): session with 4464770
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 11:30:15.01: [ 1274]: RECV FAX: bin/faxrcvd
"recvq/fax000002314.tif" "ttyS0" "000002833" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 11:30:15.01: [ 1274]: RECV FAX: end
Jun 17 11:30:15.01: [ 1274]: SESSION END

and another....
    ---- Transcript of session follows ----

Jun 17 12:39:43.51: [ 1274]: SESSION BEGIN 000002837 5714257020
Jun 17 12:39:43.51: [ 1274]: HylaFAX (tm) Version 4.2.1
Jun 17 12:39:43.52: [ 1274]: <-- [4:ATA\r]
Jun 17 12:39:55.36: [ 1274]: --> [3:FAX]
Jun 17 12:40:01.59: [ 1274]: --> [5:+FCON]
Jun 17 12:40:01.60: [ 1274]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS0'
Jun 17 12:40:01.60: [ 1274]: RECV FAX: begin
Jun 17 12:40:03.27: [ 1274]: --> [29:+FTSI: "             2409220"]
Jun 17 12:40:03.29: [ 1274]: REMOTE TSI "2409220"
Jun 17 12:40:03.62: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 12:40:03.62: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 12:40:03.62: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 12:40:03.62: [ 1274]: REMOTE wants unlimited page length
Jun 17 12:40:03.62: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 12:40:03.63: [ 1274]: REMOTE wants 2-D MR
Jun 17 12:40:03.73: [ 1274]: --> [2:OK]
Jun 17 12:40:03.74: [ 1274]: <-- [7:AT+FDR\r]
Jun 17 12:40:05.53: [ 1274]: --> [5:+FCFR]
Jun 17 12:40:07.59: [ 1274]: --> [22:+FDCS: 0,3,0,2,1,0,0,0]
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 9600 bit/s
Jun 17 12:40:07.60: [ 1274]: REMOTE wants A4 page width (215 mm)
Jun 17 12:40:07.60: [ 1274]: REMOTE wants unlimited page length
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 3.85 line/mm
Jun 17 12:40:07.60: [ 1274]: REMOTE wants 2-D MR
Jun 17 12:40:07.60: [ 1274]: --> [7:CONNECT]
Jun 17 12:40:07.60: [ 1274]: RECV: begin page
Jun 17 12:40:07.60: [ 1274]: RECV: send trigger 022
Jun 17 12:40:07.60: [ 1274]: Copy quality checking performed by host
Jun 17 12:41:27.62: [ 1274]: RECV: Missing EOL after 5 seconds
Jun 17 12:41:27.63: [ 1274]: REMOTE HANGUP: Missing EOL after 5 seconds
(section 3.2/T.4) (code 91)Jun 17 12:41:27.66: [ 1274]: RECV FAX: Missing
EOL after 5 seconds (section 3.2/T.4)
Jun 17 12:41:27.66: [ 1274]: <-- [6:AT+FK\r]
Jun 17 12:41:27.75: [ 1274]: RECV FAX (000002837): recvq/fax000002318.tif
from 2409220, route to <unspecified>, 0 pages in 1:26
Jun 17 12:41:27.76: [ 1274]: --> [8:+FHNG: 2]
Jun 17 12:41:27.76: [ 1274]: REMOTE HANGUP: Call aborted,  from +FK or
<CAN> (code 2)
Jun 17 12:41:27.76: [ 1274]: MODEM Hang up
Jun 17 12:41:27.76: [ 1274]: RECV FAX (000002837): session with 2409220
terminated abnormally: Missing EOL after 5 seconds (section 3.2/T.4)
Jun 17 12:41:27.76: [ 1274]: RECV FAX: bin/faxrcvd
"recvq/fax000002318.tif" "ttyS0" "000002837" "Missing EOL after 5 seconds
(section 3.2/T.4)" "" ""
Jun 17 12:41:27.76: [ 1274]: RECV FAX: end
Jun 17 12:41:27.76: [ 1274]: SESSION END


Slds.

--
Nestor A. Diaz
Ingeniero de Sistemas y Comp.
Tel. +57 1 6005490
Cel. +57 315 8190760
nestor@xxxxxxxxxxxxxxx
http://www.tiendalinux.com
Bogota, Colombia


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*