HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Can't receive 1-D



I had a system running hylafax (a version a couple of years old, I don't remember the version number) under Redhat 8 with a Hayes Accura 28800 modem. The system was used to receive faxes only, and worked fine.

I replaced the Redhat 8 system with an Apple XServer running MacOS X Server 10.3 and hylafax 4.2.1, keeping the same modem and modem config file. Now the system can't receive faxes using 1-D MH or 1-D MR. The receive process completes normally, but the resulting tiff file is corrupt. 2-D MR and 2-D MMR work fine.

If I try creating a new modem config file by letting faxaddmodem autoprobe, the resulting file doesn't work for receiving at all.

I'm at a complete loss as to how to fix this. Does anyone have any ideas? Below is a log file from a failed receive and the modem config file.

Thanks

- Jason

Apr 14 22:05:21.51: [ 3401]: SESSION BEGIN 000003227 12152830859
Apr 14 22:05:21.51: [ 3401]: HylaFAX (tm) Version 4.2.1
Apr 14 22:05:21.51: [ 3401]: <-- [4:ATA\r]
Apr 14 22:05:26.19: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:26.19: [ 3401]: ANSWER: FAX CONNECTION DEVICE '/dev/tty.serial'
Apr 14 22:05:26.19: [ 3401]: RECV FAX: begin
Apr 14 22:05:26.19: [ 3401]: <-- data [32]
Apr 14 22:05:26.19: [ 3401]: <-- data [2]
Apr 14 22:05:27.25: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:27.25: [ 3401]: <-- data [23]
Apr 14 22:05:27.25: [ 3401]: <-- data [2]
Apr 14 22:05:28.06: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:28.06: [ 3401]: <-- data [10]
Apr 14 22:05:28.06: [ 3401]: <-- data [2]
Apr 14 22:05:28.52: [ 3401]: --> [2:OK]
Apr 14 22:05:28.52: [ 3401]: <-- [9:AT+FRH=3\r]
Apr 14 22:05:28.93: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:30.67: [ 3401]: --> [2:OK]
Apr 14 22:05:30.67: [ 3401]: REMOTE TSI ""
Apr 14 22:05:30.67: [ 3401]: <-- [9:AT+FRH=3\r]
Apr 14 22:05:30.68: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:31.96: [ 3401]: --> [2:OK]
Apr 14 22:05:31.96: [ 3401]: REMOTE wants 14400 bit/s
Apr 14 22:05:31.96: [ 3401]: REMOTE wants A4 page width (215 mm)
Apr 14 22:05:31.96: [ 3401]: REMOTE wants unlimited page length
Apr 14 22:05:31.96: [ 3401]: REMOTE wants 7.7 line/mm
Apr 14 22:05:31.96: [ 3401]: REMOTE wants 1-D MH
Apr 14 22:05:31.96: [ 3401]: RECV training at v.17 14400 bit/s
Apr 14 22:05:31.96: [ 3401]: <-- [11:AT+FRM=145\r]
Apr 14 22:05:33.70: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:35.22: [ 3401]: RECV: TCF 2746 bytes, 1% non-zero, 2698 zero-run
Apr 14 22:05:35.23: [ 3401]: --> [10:NO CARRIER]
Apr 14 22:05:35.23: [ 3401]: DELAY 75 ms
Apr 14 22:05:35.30: [ 3401]: TRAINING succeeded
Apr 14 22:05:35.30: [ 3401]: <-- [9:AT+FTH=3\r]
Apr 14 22:05:36.29: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:36.29: [ 3401]: <-- data [3]
Apr 14 22:05:36.29: [ 3401]: <-- data [2]
Apr 14 22:05:36.58: [ 3401]: --> [2:OK]
Apr 14 22:05:36.58: [ 3401]: <-- [11:AT+FRM=146\r]
Apr 14 22:05:37.41: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:37.41: [ 3401]: RECV: begin page
Apr 14 22:05:42.75: [ 3401]: RECV: 2075 total lines, 0 bad lines, 0 consecutive bad lines
Apr 14 22:05:42.75: [ 3401]: RECV: end page
Apr 14 22:05:42.75: [ 3401]: --> [10:NO CARRIER]
Apr 14 22:05:42.75: [ 3401]: <-- [9:AT+FRH=3\r]
Apr 14 22:05:42.95: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:44.04: [ 3401]: --> [2:OK]
Apr 14 22:05:44.04: [ 3401]: RECV recv EOP (no more pages or documents)
Apr 14 22:05:44.04: [ 3401]: DELAY 70 ms
Apr 14 22:05:44.11: [ 3401]: <-- [9:AT+FTH=3\r]
Apr 14 22:05:45.19: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:45.19: [ 3401]: <-- data [3]
Apr 14 22:05:45.19: [ 3401]: <-- data [2]
Apr 14 22:05:45.57: [ 3401]: --> [2:OK]
Apr 14 22:05:45.57: [ 3401]: RECV send MCF (message confirmation)
Apr 14 22:05:45.57: [ 3401]: <-- [9:AT+FRH=3\r]
Apr 14 22:05:45.57: [ 3401]: RECV FAX (000003227): from , page 1 in 0:10, INF, 7.7 line/mm, 1-D MH, 14400 bit/s
Apr 14 22:05:45.57: [ 3401]: RECV FAX (000003227): recvq/fax000003679.tif from , route to <unspecified>, 1 pages in 0:19
Apr 14 22:05:45.98: [ 3401]: --> [7:CONNECT]
Apr 14 22:05:47.19: [ 3401]: --> [2:OK]
Apr 14 22:05:47.19: [ 3401]: RECV FAX: bin/faxrcvd "recvq/fax000003679.tif" "tty.serial" "000003227" "" "" ""
Apr 14 22:05:47.19: [ 3401]: RECV FAX: end
Apr 14 22:05:47.19: [ 3401]: SESSION END



CountryCode: 1 AreaCode: XXX FAXNumber: X.XXX.XXX.XXXX LongDistancePrefix: 1 InternationalPrefix: 011 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0666 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: XXXXXXXXXX TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 25

Class1SwitchingCmd: "<delay:7>"

#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              38400   # locked for fax sending&receiving
ModemFlowControl:       rtscts          # default
#
ModemNoFlowCmd:         AT&K0           # disable flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSetupDTRCmd:       AT&D2           # DTR off causes modem to reset
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
#
ModemDialCmd:           ATDT%s          # T for tone dialing


____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




Project hosted by iFAX Solutions