Re: [hylafax-users] (No Date: Tue, 8 Feb 2005 13:14:18 -0500

["Darren Nickerson" <darren.nickerson@xxxxxxxx>]

Hans,

The CALL records indicate an incoming call. We added them so you can compare 
CALL events with RECV events. This helps in cases where you suspect calls 
are coming in that don't lead to fax receive sessions, for whatever reason 
(like a human calling in, getting confused by the fax tones and then hanging 
up) ;-)

You would see a SEND event logged if your server was actually sending.

-Darren

----- Original Message ----- 
From: Hans Strickler
To: hylafax-users@xxxxxxxxxxx
Sent: Tuesday, February 08, 2005 1:03 PM
Subject: [hylafax-users]


We have recently upgraded to Hylafax 4-2-1 (from 4-1-8) and the Xferfaxlog 
now seems show HylaFax calling out(?)  we have heard the server TRY to call 
occasionally.  Also we are getting a lot of new errors “Failure to receive 
Silence”  and “T.30 T1 time outs”.  I have enclosed and attached copies of 
Xferstatlog, One of our errors and a modem config for one of our 2 modems.

Since the update we have had far-fewer errors, but the Recv then Call




HylaFAX xferfaxlog
                                      v------Deleted the phone #’s here
02/05/0515:32RECV000000106ttyS15222007231:011:01
02/05/0515:32CALL000000106ttyS15001:091:09
02/06/0521:46RECV000000107ttyS15222005611:211:21Failure to receive silence.
02/06/0521:45CALL000000107ttyS15001:261:26Failure to receive silence.
02/06/0521:49RECV000000108ttyS1522200561211:2011:20Failure to receive 
silence.
02/06/0521:48CALL000000108ttyS150011:2611:26Failure to receive silence.
02/06/0522:00RECV000000109ttyS15222005654:544:54
02/06/0522:00CALL000000109ttyS15004:594:59
02/06/0522:07RECV000000110ttyS15222005610:310:31
02/06/0522:07CALL000000110ttyS15000:370:37
02/07/0502:47RECV000000111ttyS14222007363:203:20
02/07/0502:47CALL000000111ttyS14003:273:27
02/07/0503:06RECV000000112ttyS14222007310:520:52
02/07/0503:06CALL000000112ttyS14001:001:00
02/07/0508:07RECV000000113ttyS15222007210:340:34
02/07/0508:07CALL000000113ttyS15000:400:40
02/07/0508:58RECV000000114ttyS14222007232:172:17Failure to receive silence.
02/07/0508:58CALL000000114ttyS14002:222:22Failure to receive silence.
02/07/0510:23RECV000000115ttyS142220072101:121:12
02/07/0510:23CALL000000115ttyS14001:191:19
02/07/0510:31RECV000000116ttyS14222007211:021:02
02/07/0510:31CALL000000116ttyS14001:091:09
02/07/0511:52CALL000000117ttyS14000:450:45No answer (T.30 T1 timeout)
02/07/0511:58CALL000000118ttyS14000:470:47No answer (T.30 T1 timeout)
02/07/0512:04CALL000000119ttyS14000:480:48No answer (T.30 T1 timeout)
02/07/0512:10RECV000000120ttyS14236752895:095:09
02/07/0512:09CALL000000120ttyS14005:175:17
02/07/0512:20CALL000000121ttyS14000:490:49No answer (T.30 T1 timeout)
02/07/0512:25CALL000000122ttyS14000:450:45No answer (T.30 T1 timeout)
02/07/0512:32RECV000000123ttyS14236752810:380:38
02/07/0512:31CALL000000123ttyS14000:440:44
02/07/0512:38CALL000000124ttyS14000:450:45No answer (T.30 T1 timeout)
02/07/0512:43CALL000000125ttyS14000:480:48No answer (T.30 T1 timeout)
02/07/0513:01RECV000000126ttyS15222007242:342:34
02/07/0513:01CALL000000126ttyS15002:402:40
02/07/0513:06RECV000000127ttyS15222007210:170:17
02/07/0513:05CALL000000127ttyS15000:240:24


\
one of our errors:

Feb 08 01:01:31.22: [10772]: SESSION BEGIN 000000150 14064065857576
Feb 08 01:01:31.22: [10772]: HylaFAX (tm) Version 4.2.1
Feb 08 01:01:31.22: [10772]: <-- [13:AT+FCLASS=1A\r]
Feb 08 01:01:36.90: [10772]: --> [7:CONNECT]
Feb 08 01:01:36.90: [10772]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS14'
Feb 08 01:01:36.90: [10772]: sched policy=1, priority=1
Feb 08 01:01:36.90: [10772]: RECV FAX: begin
Feb 08 01:01:36.90: [10772]: <-- data [32]
Feb 08 01:01:36.90: [10772]: <-- data [2]
Feb 08 01:01:36.97: [10772]: --> [7:CONNECT]
Feb 08 01:01:36.97: [10772]: <-- data [23]
Feb 08 01:01:36.97: [10772]: <-- data [2]
Feb 08 01:01:37.69: [10772]: --> [7:CONNECT]
Feb 08 01:01:37.69: [10772]: <-- data [10]
Feb 08 01:01:37.69: [10772]: <-- data [2]
Feb 08 01:01:39.87: [10772]: --> [2:OK]
Feb 08 01:01:39.87: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:01:39.99: [10772]: --> [7:CONNECT]
Feb 08 01:01:40.56: [10772]: --> [5:ERROR]
Feb 08 01:01:40.56: [10772]: MODEM Command error
Feb 08 01:01:40.56: [10772]: FCS error
Feb 08 01:01:40.56: [10772]: DELAY 1500 ms
Feb 08 01:01:42.06: [10772]: <-- [9:AT+FTH=3\r]
Feb 08 01:01:42.25: [10772]: --> [7:CONNECT]
Feb 08 01:01:42.25: [10772]: <-- data [32]
Feb 08 01:01:42.25: [10772]: <-- data [2]
Feb 08 01:01:42.42: [10772]: --> [7:CONNECT]
Feb 08 01:01:42.42: [10772]: <-- data [23]
Feb 08 01:01:42.42: [10772]: <-- data [2]
Feb 08 01:01:43.14: [10772]: --> [7:CONNECT]
Feb 08 01:01:43.14: [10772]: <-- data [10]
Feb 08 01:01:43.14: [10772]: <-- data [2]
Feb 08 01:01:45.32: [10772]: --> [2:OK]
Feb 08 01:01:45.32: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:01:47.70: [10772]: --> [7:CONNECT]
Feb 08 01:01:48.96: [10772]: --> [5:ERROR]
Feb 08 01:01:48.96: [10772]: MODEM Command error
Feb 08 01:01:48.96: [10772]: FCS error
Feb 08 01:01:48.96: [10772]: DELAY 1500 ms
Feb 08 01:01:50.46: [10772]: <-- [9:AT+FTH=3\r]
Feb 08 01:01:50.65: [10772]: --> [7:CONNECT]
Feb 08 01:01:50.65: [10772]: <-- data [32]
Feb 08 01:01:50.65: [10772]: <-- data [2]
Feb 08 01:01:50.82: [10772]: --> [7:CONNECT]
Feb 08 01:01:50.82: [10772]: <-- data [23]
Feb 08 01:01:50.82: [10772]: <-- data [2]
Feb 08 01:01:51.54: [10772]: --> [7:CONNECT]
Feb 08 01:01:51.54: [10772]: <-- data [10]
Feb 08 01:01:51.54: [10772]: <-- data [2]
Feb 08 01:01:53.72: [10772]: --> [2:OK]
Feb 08 01:01:53.72: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:01:56.82: [10772]: --> [0:]
Feb 08 01:01:56.82: [10772]: MODEM <Empty line>
Feb 08 01:01:56.82: [10772]: <-- data [1]
Feb 08 01:01:56.83: [10772]: --> [2:OK]
Feb 08 01:01:56.83: [10772]: DELAY 1500 ms
Feb 08 01:01:58.33: [10772]: <-- [9:AT+FTH=3\r]
Feb 08 01:01:58.36: [10772]: --> [7:CONNECT]
Feb 08 01:01:58.36: [10772]: <-- data [32]
Feb 08 01:01:58.36: [10772]: <-- data [2]
Feb 08 01:01:58.53: [10772]: --> [7:CONNECT]
Feb 08 01:01:58.53: [10772]: <-- data [23]
Feb 08 01:01:58.53: [10772]: <-- data [2]
Feb 08 01:01:59.25: [10772]: --> [7:CONNECT]
Feb 08 01:01:59.25: [10772]: <-- data [10]
Feb 08 01:01:59.25: [10772]: <-- data [2]
Feb 08 01:02:01.43: [10772]: --> [2:OK]
Feb 08 01:02:01.43: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:02:04.53: [10772]: --> [0:]
Feb 08 01:02:04.53: [10772]: MODEM <Empty line>
Feb 08 01:02:04.53: [10772]: <-- data [1]
Feb 08 01:02:04.53: [10772]: --> [2:OK]
Feb 08 01:02:04.53: [10772]: DELAY 1500 ms
Feb 08 01:02:06.03: [10772]: <-- [9:AT+FTH=3\r]
Feb 08 01:02:06.06: [10772]: --> [7:CONNECT]
Feb 08 01:02:06.06: [10772]: <-- data [32]
Feb 08 01:02:06.06: [10772]: <-- data [2]
Feb 08 01:02:06.23: [10772]: --> [7:CONNECT]
Feb 08 01:02:06.23: [10772]: <-- data [23]
Feb 08 01:02:06.23: [10772]: <-- data [2]
Feb 08 01:02:06.95: [10772]: --> [7:CONNECT]
Feb 08 01:02:06.95: [10772]: <-- data [10]
Feb 08 01:02:06.95: [10772]: <-- data [2]
Feb 08 01:02:09.13: [10772]: --> [2:OK]
Feb 08 01:02:09.13: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:02:12.23: [10772]: --> [0:]
Feb 08 01:02:12.23: [10772]: MODEM <Empty line>
Feb 08 01:02:12.23: [10772]: <-- data [1]
Feb 08 01:02:12.24: [10772]: --> [2:OK]
Feb 08 01:02:12.24: [10772]: DELAY 1500 ms
Feb 08 01:02:13.74: [10772]: <-- [9:AT+FTH=3\r]
Feb 08 01:02:13.77: [10772]: --> [7:CONNECT]
Feb 08 01:02:13.77: [10772]: <-- data [32]
Feb 08 01:02:13.77: [10772]: <-- data [2]
Feb 08 01:02:13.94: [10772]: --> [7:CONNECT]
Feb 08 01:02:13.94: [10772]: <-- data [23]
Feb 08 01:02:13.94: [10772]: <-- data [2]
Feb 08 01:02:14.66: [10772]: --> [7:CONNECT]
Feb 08 01:02:14.66: [10772]: <-- data [10]
Feb 08 01:02:14.66: [10772]: <-- data [2]
Feb 08 01:02:16.84: [10772]: --> [2:OK]
Feb 08 01:02:16.84: [10772]: <-- [9:AT+FRH=3\r]
Feb 08 01:02:19.94: [10772]: --> [0:]
Feb 08 01:02:19.94: [10772]: MODEM <Empty line>
Feb 08 01:02:19.94: [10772]: <-- data [1]
Feb 08 01:02:19.94: [10772]: --> [2:OK]
Feb 08 01:02:19.94: [10772]: RECV FAX: No answer (T.30 T1 timeout)
Feb 08 01:02:19.94: [10772]: RECV FAX: end
Feb 08 01:02:19.94: [10772]: SESSION END

Modem Config
# Configuration for using the Class 1 command interface with
# a USR Courier or Sportster modem and XON/XOFF flow control.
#
#
CountryCode:            1
AreaCode:         406
FAXNumber:        406-585-7576
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:  etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:       0644
RingsBeforeAnswer:      2
SpeakerVolume:          off
GettyArgs:        "-h %l dx_%s"
LocalIdentifier:  FRONTLINE
ClocalAsRoot:           no
PriorityScheduling:     yes
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
PercentGoodLines: 0
MaxConsecutiveBadLines: 0
MaxRecvPages:           150
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:        Class1            # use class 1 interface
ModemRate:        19200       # rate for DCE-DTE communication
ModemFlowControl: xonxoff           # software flow control
#
ModemSetupDTRCmd: ATS13=1&D2  # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1       # setup so DCD reflects carrier (or not)
ModemNoFlowCmd:         AT&H0&I0&R1 # setup modem for no flow control
ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
ModemResultCodesCmd:    ATQ0X4            # enable result codes
#
ModemMfrQueryCmd: !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd: ATI7        # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1 # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2 # setup modem for hardware flow control
Class1SFLOCmd:          ""          # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1    # wait after sending TCF for response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:  AT+FCLASS=0 # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A      # answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0



--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 265.8.6 - Release Date: 2/7/2005 


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*