Re: [hylafax-users] Adaptive Answer on a Intel V.92 Class 1 Modem

["Nestor A. Diaz L." <nestor@xxxxxxxxxxxxxxx>]

Here is the output:

Jan 11 10:04:27.36: [24919]: SESSION BEGIN 000000042 5716017799
Jan 11 10:04:27.36: [24919]: HylaFAX (tm) Version 4.2.0
Jan 11 10:04:27.36: [24919]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Jan 11 10:04:27.36: [24919]: <-- [4:ATA\r]
Jan 11 10:04:43.63: [24919]: --> [3:DAT]
Jan 11 10:04:43.63: [24919]: --> [13:CONNECT 19200]
Jan 11 10:04:43.63: [24919]: ANSWER: DATA CONNECTION
Jan 11 10:04:43.63: [24919]: GETTY: START "/etc/hylafax/getty-link -r -b -s 19200 ttyS0", pid 249
28
Jan 11 10:05:26.46: [24919]: CLOSE /dev/ttyS0

The modem always answer in data mode, the problem is even bigger because
if i try to send a fax then the systems execute the getty-link program and
locks the device forever.

Thanks.

--
Nestor A. Diaz
Ingeniero de Sistemas y Comp.
Tel. +57 1 6005490
Cel. +57 315 8190760
nestor@xxxxxxxxxxxxxxx
http://www.tiendalinux.com
Bogota, Colombia

On Tue, 11 Jan 2005, George Bell wrote:

> On Tuesday 11 January 2005 09:25, Nestor A. Diaz L. wrote:
> > On Tue, 11 Jan 2005, George Bell wrote:
> > > Dou you have a line like:
> > > ModemSetupAACmd:		AT+FAA=1
> > > in your config file?
> >
> > Yes, i have followed the instructions on the debian documentation for
> > hylafax:
> >
> > ------- in /etc/hylafax/config.ttyS1:
> >
> > ModemSetupAACmd: AT+FAA=1
> > AdaptiveAnswer:         yes
> >
> > #mgetty:
> > #  -x 9 : full debugging to /var/log/mgetty/mg_ttyS1.log
> > #  -r   : direct line -- don't initialize modem
> > #  -b   : non-blocking -- don't wait for ^M before prompting
> > #  -s %s: set speed
> > #  %l   : set device
> > GettyArgs:      "-r -b -s %s %l"
> >
> > ------- in /etc/mgetty/mgetty.config:
> > # modem controlled by faxgetty
> > port ttyS1
> >    # already accepted data call, do not reset
> >    toggle-dtr n
> >
> > But it doesn't work, i have usted this technique before with class 2.0
> > modems and works, but with this it doesn't.
> >
> 
> Can you post a session log for when you receive a data call?
> If you can, set "SessionTracing" to 0xFF
> 
> George
> 
> 
> ____________________ HylaFAX(tm) Users Mailing List _______________________
>   To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
>  On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
>   *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
> 


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*