HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] USR 5601 98F7 giving error: T.30 T2 timeout, expected page not received



Howdy list folks,

I am having this receive problem almost every time from certain senders (this is a different server than I was discussing a few weeks ago).

The situation is as follows:

Linux (RedHat 9)
HylaFAX 4.2.0 from rpm (hylafax-4.2.0-1rh9)
Multitech modem on ttyS5 (this one is send only so it is not involved in the problem)
USR internal 56K modem on ttyS4 (this is receive only and has the problem):
ati0: 5601
ati1: 98F7
ati2: OK
ati3: U.S. Robotics 56K FAX INT Rev. 5.22.16


In this set of attempts, the fax was 12 pages. It was sent gradually over 9 attempts (log for 3rd attempt attached) (communicating by voice as to which pages had worked). On some tries less than half a page went through before the error, sometimes 3 or 4 pages went through.

This same setup has been chugging along pretty reliably for several months with 4.2.0 and a year or two before that with 4.1.8. Can the modem just be aging and having components burn out or becoming unpredictable?

The 2550 ms timeout which accounted for my earlier problem (on a different server) does not seem to be the problem here. The timeouts seem to be a different length (5 s) here, and anyway, I don't think this is a Topic chipset (though I guess I don't know how to tell that definitively).

Is it possible the oldness/slowness of the CPU could be a factor here? It is a Pentium MMX 166 MHz but is not running anything else and is generally at about 99% idle.

Are there any suggestions as to possible reasons or remedies?

Thanks and regards.

Martin



  Quality: Normal
     Page: 1728 by 31
 Received: 2004:12:20 13:56:08
TimeToRecv: 0:05
SignalRate: 14400 bit/s
DataFormat: 1-D MH
ErrCorrect: No
ReceivedOn: ttyS4

The full document was not received because:

T.30 T2 timeout, expected page not received

---- Transcript of session follows ----

Dec 20 13:55:52.26: [18839]: SESSION BEGIN 000017334 14164254233
Dec 20 13:55:52.26: [18839]: HylaFAX (tm) Version 4.2.0
Dec 20 13:55:52.26: [18839]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Dec 20 13:55:52.26: [18839]: <-- [13:AT+FCLASS=1A\r]
Dec 20 13:55:57.95: [18839]: --> [7:CONNECT]
Dec 20 13:55:57.95: [18839]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyS4'
Dec 20 13:55:57.95: [18839]: STATE CHANGE: ANSWERING -> RECEIVING
Dec 20 13:55:57.95: [18839]: MODEM input buffering enabled
Dec 20 13:55:57.95: [18839]: RECV FAX: begin
Dec 20 13:55:57.95: [18839]: MODEM input buffering disabled
Dec 20 13:55:57.95: [18839]: <-- HDLC<32:FF C0 04 AD 00 55 12 9E 36 86 62 82 1A 04 14 2E B6 94 04 6A A6 4E CE 96 F6 76 04 2C 74 4C 74 0C>
Dec 20 13:55:58.02: [18839]: --> [7:CONNECT]
Dec 20 13:55:58.02: [18839]: <-- HDLC<23:FF C0 02 FA FA FA 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Dec 20 13:55:58.74: [18839]: --> [7:CONNECT]
Dec 20 13:55:58.74: [18839]: <-- HDLC<10:FF C8 01 00 76 5F 23 01 FB C0>
Dec 20 13:56:00.92: [18839]: --> [2:OK]
Dec 20 13:56:00.92: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:02.23: [18839]: --> [7:CONNECT]
Dec 20 13:56:03.68: [18839]: --> HDLC<25:FF C0 C2 8C 4C CC 8C 2C 1C 6C AC 0C 9C 04 04 04 04 04 04 04 04 04 04 00 F0>
Dec 20 13:56:03.68: [18839]: --> [2:OK]
Dec 20 13:56:03.68: [18839]: REMOTE TSI "9056841321"
Dec 20 13:56:03.68: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:03.70: [18839]: --> [7:CONNECT]
Dec 20 13:56:03.94: [18839]: --> HDLC<8:FF C8 C1 00 44 1E 63 22>
Dec 20 13:56:03.95: [18839]: --> [2:OK]
Dec 20 13:56:03.95: [18839]: REMOTE wants 14400 bit/s
Dec 20 13:56:03.95: [18839]: REMOTE wants A4 page width (215 mm)
Dec 20 13:56:03.95: [18839]: REMOTE wants unlimited page length
Dec 20 13:56:03.95: [18839]: REMOTE wants 3.85 line/mm
Dec 20 13:56:03.95: [18839]: REMOTE wants 1-D MH
Dec 20 13:56:03.95: [18839]: RECV training at v.17 14400 bit/s
Dec 20 13:56:03.95: [18839]: MODEM set XON/XOFF/DRAIN: input ignored, output generated
Dec 20 13:56:03.95: [18839]: <-- [11:AT+FRM=145\r]
Dec 20 13:56:05.76: [18839]: --> [7:CONNECT]
Dec 20 13:56:07.32: [18839]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Dec 20 13:56:07.32: [18839]: RECV: TCF 2813 bytes, 2% non-zero, 2714 zero-run
Dec 20 13:56:07.33: [18839]: --> [10:NO CARRIER]
Dec 20 13:56:07.33: [18839]: DELAY 75 ms
Dec 20 13:56:07.41: [18839]: TRAINING succeeded
Dec 20 13:56:07.41: [18839]: <-- [9:AT+FTH=3\r]
Dec 20 13:56:07.61: [18839]: --> [7:CONNECT]
Dec 20 13:56:07.61: [18839]: <-- HDLC<3:FF C8 21>
Dec 20 13:56:08.78: [18839]: --> [2:OK]
Dec 20 13:56:08.78: [18839]: MODEM input buffering enabled
Dec 20 13:56:08.78: [18839]: MODEM set XON/XOFF/FLUSH: input ignored, output generated
Dec 20 13:56:08.78: [18839]: <-- [11:AT+FRM=146\r]
Dec 20 13:56:10.04: [18839]: --> [7:CONNECT]
Dec 20 13:56:10.04: [18839]: RECV: begin page
Dec 20 13:56:12.34: [18839]: RECV/CQ: Bad 1D pixel count, row 120, got 2087, expected 1728
Dec 20 13:56:12.34: [18839]: RECV/CQ: Adjusting for trailing noise (1 run)
Dec 20 13:56:12.34: [18839]: RECV: 120 total lines, 0 bad lines, 0 consecutive bad lines
Dec 20 13:56:12.34: [18839]: RECV: end page
Dec 20 13:56:12.34: [18839]: --> [10:NO CARRIER]
Dec 20 13:56:12.34: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:16.21: [18839]: --> [7:CONNECT]
Dec 20 13:56:16.21: [18839]: --> [19:59 CD 45 15 3B 88 A5 D1 44 28 40 87 9D 3A CF CB 1C 10 03]
Dec 20 13:56:16.21: [18839]: --> [5:ERROR]
Dec 20 13:56:16.21: [18839]: MODEM Command error
Dec 20 13:56:16.21: [18839]: FCS error
Dec 20 13:56:16.21: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:16.33: [18839]: --> [7:CONNECT]
Dec 20 13:56:18.20: [18839]: --> [20:8D C2 04 85 7A 46 A2 62 30 49 01 73 83 92 99 10 10 F8 10 03]
Dec 20 13:56:18.20: [18839]: --> [5:ERROR]
Dec 20 13:56:18.20: [18839]: MODEM Command error
Dec 20 13:56:18.20: [18839]: FCS error
Dec 20 13:56:18.20: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:18.32: [18839]: --> [7:CONNECT]
Dec 20 13:56:19.18: [18839]: --> [8:AB 27 6F E4 EF DD 10 03]
Dec 20 13:56:19.18: [18839]: --> [5:ERROR]
Dec 20 13:56:19.18: [18839]: MODEM Command error
Dec 20 13:56:19.18: [18839]: FCS error
Dec 20 13:56:19.18: [18839]: <-- [9:AT+FRH=3\r]
Dec 20 13:56:19.30: [18839]: --> [7:CONNECT]
Dec 20 13:56:24.30: [18839]: MODEM TIMEOUT: receiving HDLC frame data
Dec 20 13:56:24.41: [18839]: --> [2:OK]
Dec 20 13:56:24.41: [18839]: RECV keeping unconfirmed page
Dec 20 13:56:24.41: [18839]: RECV FAX (000017334): from 9056841321, page 1 in 0:17, INF, 3.85 line/mm, 1-D MH, 14400 bit/s
Dec 20 13:56:24.41: [18839]: RECV FAX (000017334): recvq/fax000000997.tif from 9056841321, route to <unspecified>, 1 pages in 0:27
Dec 20 13:56:24.41: [18839]: RECV FAX: T.30 T2 timeout, expected page not received
Dec 20 13:56:24.41: [18839]: <-- [9:AT+FTH=3\r]
Dec 20 13:56:24.55: [18839]: --> [7:CONNECT]
Dec 20 13:56:24.55: [18839]: <-- HDLC<3:FF C8 5F>
Dec 20 13:56:25.73: [18839]: --> [2:OK]
Dec 20 13:56:25.73: [18839]: MODEM input buffering enabled
Dec 20 13:56:25.73: [18839]: RECV FAX (000017334): session with 9056841321 terminated abnormally: T.30 T2 timeout, expected page not received
Dec 20 13:56:25.73: [18839]: RECV FAX: bin/faxrcvd "recvq/fax000000997.tif" "ttyS4" "000017334" "T.30 T2 timeout, expected page not received" "" ""
Dec 20 13:56:25.75: [18839]: RECV FAX: end
Dec 20 13:56:25.75: [18839]: SESSION END







____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*




Project hosted by iFAX Solutions