Re: [hylafax-users] Problem with a Devolo Micolink 56k FunII

[Matthias Reich <rei@xxxxxxxx>]

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Am Mittwoch, 17. November 2004 16:45 schrieb Lee Howard:
> On 2004.11.17 00:18 Matthias Reich wrote:
> > I set up a 4.2.0 server on my notebook and tried again, but with the
> > same
> > results.
>
> Does this only happen to certain receivers?  Or to all of them?
>
> Can you send a fax to a HylaFAX receiver and send the receiving log?
>
> Lee.


Hi Lee,

this does only happen to certain receivers, as I found out in the logs
the remote equipment identifies itself as:

NSF remote fax equipment: Brother Intellifax 770

or just

NSF remote fax equipment: Brother

When I compare the logs, I can find a difference in the HDLC-lines, not 
knowing what the are good for

successful:
HDLC<23:FF C0 C2 2A 4A 82 E2 2A 2A AA 2A CA 04 E2 A2 04 CA F2 E2 82 12 04 04>
data [23]
data [2]
[7:CONNECT]
HDLC<6:FF C8 C1 00 45 14>
data [6]
data [2]
[2:OK]
TRAINING succeeded

Brother:
HDLC<23:FF C0 C2 2A 4A 82 E2 2A 2A AA 2A CA 04 E2 A2 04 CA F2 E2 82 12 04 04>
data [23]
data [2]
[7:CONNECT]
HDLC<6:FF C8 C1 00 44 1E>
data [6]
data [2]
[2:OK]
[9:AT+FTS=7\r]
[2:OK]
[11:AT+FTM=145\r]
[7:CONNECT]
data [1024]
data [1024]
data [652]
data [2]
[2:OK]
[9:AT+FRH=3\r]
[7:CONNECT]
HDLC<5:FF C8 22 67 DD>
[2:OK]


comparing these two log, I can only find a difference in the HDLC-lines.
HDLC<6:FF C8 C1 00 45 14> -> successful
HDLC<6:FF C8 C1 00 44 1E> -> not successful

Is that what is causing the failures, and if yes, how can I avoid it in 
future.
In the one case the training succeeded, in the (br)other-case the modem sends 
AT+FTS=7 instead.


Here is a log to a destination which can receive from the devolo modem:


Nov 17 07:40:22.50: [ 3023]: MODEM input buffering enabled
Nov 17 07:40:22.51: [ 3023]: <-- [12:AT+FCLASS=1\r]
Nov 17 07:40:22.61: [ 3023]: --> [2:OK]
Nov 17 07:40:22.61: [ 3023]: DIAL 0985770962
Nov 17 07:40:22.61: [ 3023]: <-- [17:ATDT0,0985770962\r]
Nov 17 07:40:44.30: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:44.30: [ 3023]: MODEM input buffering disabled
Nov 17 07:40:46.15: [ 3023]: --> HDLC<41:FF C0 04 00 00 88 01 00 51 92 08 12 
A2 92 42 92 04 B2 A2 2A 82 32 32 04 04 04 04 00 F2 00 01 01 1B 71 80 80 80 80 
20 19 0A>
Nov 17 07:40:46.15: [ 3023]: --> [2:OK]
Nov 17 07:40:46.15: [ 3023]: REMOTE NSF "00 00 11 80 00 8A 49 10 48 45 49 42 
49 20 4D 45 54 41 4C 4C 20 20 20 20 00 4F 00 80 80 D8 8E 01 01 01 01 04 98"
Nov 17 07:40:46.15: [ 3023]: NSF remote fax equipment: Canon Laser Class 9000 
Series
Nov 17 07:40:46.15: [ 3023]: NSF remote station ID: "HEIBI METALL    "
Nov 17 07:40:46.15: [ 3023]: <-- [9:AT+FRH=3\r]
Nov 17 07:40:46.17: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:46.84: [ 3023]: --> HDLC<25:FF C0 02 4C 6C 9C 0C EC 04 EC AC 1C 
9C 04 9C 2C 04 04 04 04 04 04 04 4E 97>
Nov 17 07:40:46.84: [ 3023]: --> [2:OK]
Nov 17 07:40:46.84: [ 3023]: REMOTE CSI "49 9857 70962"
Nov 17 07:40:46.84: [ 3023]: <-- [9:AT+FRH=3\r]
Nov 17 07:40:46.86: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:47.11: [ 3023]: --> HDLC<9:FF C8 01 00 77 15 22 17 5D>
Nov 17 07:40:47.11: [ 3023]: --> [2:OK]
Nov 17 07:40:47.11: [ 3023]: REMOTE best rate 14400 bit/s
Nov 17 07:40:47.11: [ 3023]: REMOTE max page width 1728 pixels in 215 mm
Nov 17 07:40:47.11: [ 3023]: REMOTE max unlimited page length
Nov 17 07:40:47.11: [ 3023]: REMOTE best vres 7.7 line/mm
Nov 17 07:40:47.11: [ 3023]: REMOTE best format 2-D MMR
Nov 17 07:40:47.11: [ 3023]: REMOTE supports T.30 Annex A, ECM
Nov 17 07:40:47.11: [ 3023]: REMOTE best 10 ms/scanline
Nov 17 07:40:47.11: [ 3023]: USE 14400 bit/s
Nov 17 07:40:47.11: [ 3023]: USE 10 ms/scanline
Nov 17 07:40:47.11: [ 3023]: SEND file "docq/doc11961.ps;40"
Nov 17 07:40:47.11: [ 3023]: USE page width 1728 pixels in 215 mm
Nov 17 07:40:47.11: [ 3023]: USE unlimited page length
Nov 17 07:40:47.11: [ 3023]: USE 3.85 line/mm
Nov 17 07:40:47.11: [ 3023]: USE 2-D MR
Nov 17 07:40:47.11: [ 3023]: SEND training at v.17 14400 bit/s
Nov 17 07:40:47.11: [ 3023]: <-- [9:AT+FTH=3\r]
Nov 17 07:40:47.21: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:47.21: [ 3023]: <-- HDLC<23:FF C0 C2 2A 4A 82 E2 2A 2A AA 2A CA 
04 E2 A2 04 CA F2 E2 82 12 04 04>
Nov 17 07:40:47.21: [ 3023]: <-- data [23]
Nov 17 07:40:47.21: [ 3023]: <-- data [2]
Nov 17 07:40:48.21: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:48.21: [ 3023]: <-- HDLC<6:FF C8 C1 00 45 14>
Nov 17 07:40:48.21: [ 3023]: <-- data [6]
Nov 17 07:40:48.21: [ 3023]: <-- data [2]
Nov 17 07:40:49.23: [ 3023]: --> [2:OK]
Nov 17 07:40:49.23: [ 3023]: <-- [9:AT+FTS=7\r]
Nov 17 07:40:49.31: [ 3023]: --> [2:OK]
Nov 17 07:40:49.31: [ 3023]: <-- [11:AT+FTM=145\r]
Nov 17 07:40:50.74: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:50.75: [ 3023]: <-- data [1024]
Nov 17 07:40:50.75: [ 3023]: <-- data [1024]
Nov 17 07:40:50.75: [ 3023]: <-- data [652]
Nov 17 07:40:50.89: [ 3023]: <-- data [2]
Nov 17 07:40:52.41: [ 3023]: --> [2:OK]
Nov 17 07:40:52.41: [ 3023]: <-- [9:AT+FRH=3\r]
Nov 17 07:40:52.79: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:53.75: [ 3023]: --> HDLC<5:FF C8 21 57 BE>
Nov 17 07:40:53.75: [ 3023]: --> [2:OK]
Nov 17 07:40:53.75: [ 3023]: TRAINING succeeded
Nov 17 07:40:53.75: [ 3023]: DELAY 75 ms
Nov 17 07:40:53.82: [ 3023]: <-- [11:AT+FTM=146\r]
Nov 17 07:40:54.01: [ 3023]: --> [7:CONNECT]
Nov 17 07:40:54.01: [ 3023]: SEND begin page
Nov 17 07:40:54.01: [ 3023]: <-- data [1027]
Nov 17 07:40:54.01: [ 3023]: <-- data [1028]
Nov 17 07:40:54.01: [ 3023]: <-- data [1028]
Nov 17 07:40:54.27: [ 3023]: <-- data [1026]
Nov 17 07:40:54.54: [ 3023]: <-- data [1029]
Nov 17 07:40:54.82: [ 3023]: <-- data [1033]
Nov 17 07:40:55.32: [ 3023]: <-- data [1026]
Nov 17 07:40:55.96: [ 3023]: <-- data [1026]
Nov 17 07:40:56.59: [ 3023]: <-- data [1035]
Nov 17 07:40:57.02: [ 3023]: <-- data [1032]
Nov 17 07:40:57.66: [ 3023]: <-- data [1030]
Nov 17 07:40:58.15: [ 3023]: <-- data [1035]
Nov 17 07:40:58.79: [ 3023]: <-- data [1036]
Nov 17 07:40:59.43: [ 3023]: <-- data [1032]
Nov 17 07:41:00.00: [ 3023]: <-- data [1040]
Nov 17 07:41:00.49: [ 3023]: <-- data [1036]
Nov 17 07:41:01.14: [ 3023]: <-- data [1033]
Nov 17 07:41:01.71: [ 3023]: <-- data [1033]
Nov 17 07:41:02.19: [ 3023]: <-- data [1034]
Nov 17 07:41:02.62: [ 3023]: <-- data [1034]
Nov 17 07:41:03.27: [ 3023]: <-- data [136]
Nov 17 07:41:03.32: [ 3023]: SENT 20616 bytes of data
Nov 17 07:41:03.32: [ 3023]: <-- data [1033]
Nov 17 07:41:03.96: [ 3023]: <-- data [1031]
Nov 17 07:41:04.44: [ 3023]: <-- data [1032]
Nov 17 07:41:05.08: [ 3023]: <-- data [1024]
Nov 17 07:41:05.65: [ 3023]: <-- data [1024]
Nov 17 07:41:06.12: [ 3023]: <-- data [1026]
Nov 17 07:41:06.76: [ 3023]: <-- data [1034]
Nov 17 07:41:07.42: [ 3023]: <-- data [1025]
Nov 17 07:41:07.99: [ 3023]: <-- data [1007]
Nov 17 07:41:08.47: [ 3023]: SENT 9193 bytes of data
Nov 17 07:41:08.47: [ 3023]: SEND 2D RTC
Nov 17 07:41:08.47: [ 3023]: <-- data [30]
Nov 17 07:41:08.48: [ 3023]: <-- data [2]
Nov 17 07:41:08.49: [ 3023]: SEND end page
Nov 17 07:41:10.76: [ 3023]: --> [2:OK]
Nov 17 07:41:10.76: [ 3023]: <-- [9:AT+FTS=7\r]
Nov 17 07:41:10.84: [ 3023]: --> [2:OK]
Nov 17 07:41:10.84: [ 3023]: SEND send MPS (more pages, same document)
Nov 17 07:41:10.84: [ 3023]: <-- [9:AT+FTH=3\r]
Nov 17 07:41:10.91: [ 3023]: --> [7:CONNECT]
Nov 17 07:41:10.91: [ 3023]: <-- HDLC<3:FF C8 F2>
Nov 17 07:41:10.91: [ 3023]: <-- data [3]
Nov 17 07:41:10.91: [ 3023]: <-- data [2]
Nov 17 07:41:12.16: [ 3023]: --> [2:OK]
Nov 17 07:41:12.16: [ 3023]: <-- [9:AT+FRH=3\r]
Nov 17 07:41:12.52: [ 3023]: --> [7:CONNECT]
Nov 17 07:41:13.50: [ 3023]: --> HDLC<5:FF C8 31 45 8F>
Nov 17 07:41:13.50: [ 3023]: --> [2:OK]
Nov 17 07:41:13.50: [ 3023]: SEND recv MCF (message confirmation)
Nov 17 07:41:13.50: [ 3023]: SEND FAX (00017803): FROM streha@xxxxxxxxxxxxxx 
TO 0985770962 (page 1 of 2 sent in 0:26)


As we have a bunch of this devolo modems here I send a fax from one Devolo to 
another.

Here ist the result of the receiving modem:

Nov 18 07:59:41.65: [32116]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyUSB2'
Nov 18 07:59:41.65: [32116]: MODEM input buffering enabled
Nov 18 07:59:41.65: [32116]: RECV FAX: begin
Nov 18 07:59:41.67: [32116]: MODEM input buffering disabled
Nov 18 07:59:41.67: [32116]: <-- HDLC<23:FF C0 02 2A 4A 82 E2 2A 2A AA 2A CA 
04 E2 A2 04 CA F2 E2 82 12 04 04>
Nov 18 07:59:41.67: [32116]: <-- data [23]
Nov 18 07:59:41.67: [32116]: <-- data [2]
Nov 18 07:59:42.55: [32116]: --> [7:CONNECT]
Nov 18 07:59:42.55: [32116]: <-- HDLC<10:FF C8 01 00 77 5F 01 79 03 C0>
Nov 18 07:59:42.55: [32116]: <-- data [10]
Nov 18 07:59:42.55: [32116]: <-- data [2]
Nov 18 07:59:43.68: [32116]: --> [2:OK]
Nov 18 07:59:43.68: [32116]: <-- [9:AT+FRH=3\r]
Nov 18 07:59:44.05: [32116]: --> [7:CONNECT]
Nov 18 07:59:45.54: [32116]: --> HDLC<25:FF C0 C2 2A 4A 82 E2 2A 2A AA 2A CA 
04 E2 A2 04 CA F2 E2 82 12 04 04 FF DD>
Nov 18 07:59:45.54: [32116]: --> [2:OK]
Nov 18 07:59:45.54: [32116]: REMOTE TSI "HAGOS EG STUTTGART"
Nov 18 07:59:45.54: [32116]: <-- [9:AT+FRH=3\r]
Nov 18 07:59:45.56: [32116]: --> [7:CONNECT]
Nov 18 07:59:45.78: [32116]: --> HDLC<8:FF C8 C1 00 44 1E 63 22>
Nov 18 07:59:45.78: [32116]: --> [2:OK]
Nov 18 07:59:45.78: [32116]: REMOTE wants 14400 bit/s
Nov 18 07:59:45.78: [32116]: REMOTE wants page width 1728 pixels in 215 mm
Nov 18 07:59:45.78: [32116]: REMOTE wants unlimited page length
Nov 18 07:59:45.78: [32116]: REMOTE wants 3.85 line/mm
Nov 18 07:59:45.78: [32116]: REMOTE wants 1-D MR
Nov 18 07:59:45.78: [32116]: RECV training at v.17 14400 bit/s
Nov 18 07:59:45.78: [32116]: <-- [11:AT+FRM=145\r]
Nov 18 07:59:47.34: [32116]: --> [7:CONNECT]
Nov 18 07:59:49.07: [32116]: RECV: TCF 3052 bytes, 2% non-zero, 2699 zero-run
Nov 18 07:59:49.09: [32116]: --> [10:NO CARRIER]
Nov 18 07:59:49.09: [32116]: DELAY 75 ms
Nov 18 07:59:49.16: [32116]: TRAINING succeeded
Nov 18 07:59:49.16: [32116]: <-- [9:AT+FTH=3\r]
Nov 18 07:59:49.24: [32116]: --> [7:CONNECT]
Nov 18 07:59:49.24: [32116]: <-- HDLC<3:FF C8 21>
Nov 18 07:59:49.24: [32116]: <-- data [3]
Nov 18 07:59:49.24: [32116]: <-- data [2]
Nov 18 07:59:50.48: [32116]: --> [2:OK]
Nov 18 07:59:50.48: [32116]: MODEM input buffering enabled
Nov 18 07:59:50.49: [32116]: <-- [11:AT+FRM=146\r]
Nov 18 07:59:50.82: [32116]: --> [7:CONNECT]
Nov 18 07:59:50.82: [32116]: RECV: begin page
Nov 18 08:01:11.36: [32116]: RECV: 1145 total lines, 0 bad lines, 0 
consecutive bad lines
Nov 18 08:01:11.36: [32116]: RECV: end page
Nov 18 08:01:11.36: [32116]: --> [10:NO CARRIER]
Nov 18 08:01:11.36: [32116]: MODEM input buffering disabled
Nov 18 08:01:11.36: [32116]: <-- [9:AT+FRH=3\r]
Nov 18 08:01:11.67: [32116]: --> [7:CONNECT]
Nov 18 08:01:12.60: [32116]: --> HDLC<5:FF C8 F4 CC 66>
Nov 18 08:01:12.60: [32116]: --> [2:OK]
Nov 18 08:01:12.60: [32116]: RECV recv EOP (no more pages or documents)
Nov 18 08:01:12.60: [32116]: DELAY 70 ms
Nov 18 08:01:12.66: [32116]: <-- [9:AT+FTH=3\r]
Nov 18 08:01:12.76: [32116]: --> [7:CONNECT]
Nov 18 08:01:12.76: [32116]: <-- HDLC<3:FF C8 31>
Nov 18 08:01:12.76: [32116]: <-- data [3]
Nov 18 08:01:12.76: [32116]: <-- data [2]
Nov 18 08:01:14.00: [32116]: --> [2:OK]
Nov 18 08:01:14.00: [32116]: RECV send MCF (message confirmation)
Nov 18 08:01:14.00: [32116]: RECV FAX (00017879): from HAGOS EG STUTTGART, 
page 1 in 1:25, INF, 3.85 line/mm, 1-D MR, 14400 bit/s
Nov 18 08:01:14.01: [32116]: RECV FAX (00017879): recvq/fax00212.tif from 
HAGOS EG STUTTGART, route to <unspecified>, 1 pages in 1:33
Nov 18 08:01:14.02: [32116]: <-- [9:AT+FRH=3\r]
Nov 18 08:01:14.36: [32116]: --> [7:CONNECT]
Nov 18 08:01:15.34: [32116]: --> HDLC<5:FF C8 DF 59 6F>
Nov 18 08:01:15.34: [32116]: --> [2:OK]
Nov 18 08:01:15.34: [32116]: MODEM input buffering enabled
Nov 18 08:01:15.34: [32116]: RECV FAX: bin/faxrcvd.hagos "recvq/fax00212.tif" 
"ttyUSB2" "00017879" "" "" ""
Nov 18 08:01:15.67: [32116]: RECV FAX: end
Nov 18 08:01:15.67: [32116]: SESSION END

This is the log from the sending modem:

Nov 18 07:59:09.09: [32639]: SEND FAX: JOB 11944 DEST 07117880537 COMMID 
00017878 DEVICE '/dev/ttyUSB1'
Nov 18 07:59:09.09: [32639]: MODEM set DTR OFF
Nov 18 07:59:09.09: [32639]: DELAY 75 ms
Nov 18 07:59:09.16: [32639]: MODEM set DTR ON
Nov 18 07:59:09.16: [32639]: DELAY 2600 ms
Nov 18 07:59:12.78: [32639]: MODEM set baud rate: 38400 baud, input flow 
RTS/CTS, output flow RTS/CTS
Nov 18 07:59:12.79: [32639]: DELAY 10 ms
Nov 18 07:59:12.79: [32639]: MODEM flush i/o
Nov 18 07:59:12.79: [32639]: <-- [4:ATZ\r]
Nov 18 07:59:12.80: [32639]: --> [2:OK]
Nov 18 07:59:12.80: [32639]: DELAY 3000 ms
Nov 18 07:59:15.79: [32639]: <-- [16:ATZ ATX3 ATS0=2\r]
Nov 18 07:59:15.81: [32639]: --> [15:ATZ ATX3 ATS0=2]
Nov 18 07:59:15.81: [32639]: --> [2:OK]
Nov 18 07:59:15.81: [32639]: <-- [5:ATE0\r]
Nov 18 07:59:15.83: [32639]: --> [4:ATE0]
Nov 18 07:59:15.83: [32639]: --> [2:OK]
Nov 18 07:59:15.83: [32639]: <-- [5:ATV1\r]
Nov 18 07:59:15.84: [32639]: --> [2:OK]
Nov 18 07:59:15.84: [32639]: <-- [5:ATQ0\r]
Nov 18 07:59:15.86: [32639]: --> [2:OK]
Nov 18 07:59:15.86: [32639]: <-- [7:ATS0=0\r]
Nov 18 07:59:15.88: [32639]: --> [2:OK]
Nov 18 07:59:15.88: [32639]: <-- [7:ATS8=2\r]
Nov 18 07:59:15.89: [32639]: --> [2:OK]
Nov 18 07:59:15.89: [32639]: <-- [8:ATS7=60\r]
Nov 18 07:59:15.91: [32639]: --> [2:OK]
Nov 18 07:59:15.91: [32639]: <-- [12:AT+FCLASS=1\r]
Nov 18 07:59:15.92: [32639]: --> [2:OK]
Nov 18 07:59:15.92: [32639]: <-- [5:ATM0\r]
Nov 18 07:59:15.94: [32639]: --> [2:OK]
Nov 18 07:59:15.94: [32639]: MODEM input buffering enabled
Nov 18 07:59:15.94: [32639]: <-- [12:AT+FCLASS=1\r]
Nov 18 07:59:16.05: [32639]: --> [2:OK]
Nov 18 07:59:16.06: [32639]: DIAL 07117880537
Nov 18 07:59:16.06: [32639]: <-- [18:ATDT0,07117880537\r]
Nov 18 07:59:41.90: [32639]: --> [7:CONNECT]
Nov 18 07:59:41.90: [32639]: MODEM input buffering disabled
Nov 18 07:59:43.29: [32639]: --> HDLC<25:FF C0 02 2A 4A 82 E2 2A 2A AA 2A CA 
04 E2 A2 04 CA F2 E2 82 12 04 04 D2 47>
Nov 18 07:59:43.29: [32639]: --> [2:OK]
Nov 18 07:59:43.29: [32639]: REMOTE CSI "HAGOS EG STUTTGART"
Nov 18 07:59:43.29: [32639]: <-- [9:AT+FRH=3\r]
Nov 18 07:59:43.31: [32639]: --> [7:CONNECT]
Nov 18 07:59:43.64: [32639]: --> HDLC<12:FF C8 01 00 77 5F 01 79 03 C0 BC A1>
Nov 18 07:59:43.64: [32639]: --> [2:OK]
Nov 18 07:59:43.64: [32639]: REMOTE best rate 14400 bit/s
Nov 18 07:59:43.64: [32639]: REMOTE max page width 2432 pixels in 303 mm
Nov 18 07:59:43.64: [32639]: REMOTE max unlimited page length
Nov 18 07:59:43.64: [32639]: REMOTE best vres 7.7 line/mm
Nov 18 07:59:43.64: [32639]: REMOTE best format 2-D MR
Nov 18 07:59:43.64: [32639]: REMOTE best 0 ms/scanline
Nov 18 07:59:43.64: [32639]: USE 14400 bit/s
Nov 18 07:59:43.64: [32639]: USE 0 ms/scanline
Nov 18 07:59:43.64: [32639]: SEND file "docq/doc12002.ps;00"
Nov 18 07:59:43.64: [32639]: USE page width 1728 pixels in 215 mm
Nov 18 07:59:43.64: [32639]: USE unlimited page length
Nov 18 07:59:43.64: [32639]: USE 3.85 line/mm
Nov 18 07:59:43.64: [32639]: USE 1-D MR
Nov 18 07:59:43.64: [32639]: SEND training at v.17 14400 bit/s
Nov 18 07:59:43.64: [32639]: <-- [9:AT+FTH=3\r]
Nov 18 07:59:43.79: [32639]: --> [7:CONNECT]
Nov 18 07:59:43.79: [32639]: <-- HDLC<23:FF C0 C2 2A 4A 82 E2 2A 2A AA 2A CA 
04 E2 A2 04 CA F2 E2 82 12 04 04>
Nov 18 07:59:43.79: [32639]: <-- data [23]
Nov 18 07:59:43.79: [32639]: <-- data [2]
Nov 18 07:59:44.79: [32639]: --> [7:CONNECT]
Nov 18 07:59:44.79: [32639]: <-- HDLC<6:FF C8 C1 00 44 1E>
Nov 18 07:59:44.79: [32639]: <-- data [6]
Nov 18 07:59:44.79: [32639]: <-- data [2]
Nov 18 07:59:45.81: [32639]: --> [2:OK]
Nov 18 07:59:45.81: [32639]: <-- [9:AT+FTS=7\r]
Nov 18 07:59:45.89: [32639]: --> [2:OK]
Nov 18 07:59:45.89: [32639]: <-- [11:AT+FTM=145\r]
Nov 18 07:59:47.32: [32639]: --> [7:CONNECT]
Nov 18 07:59:47.32: [32639]: <-- data [1024]
Nov 18 07:59:47.32: [32639]: <-- data [1024]
Nov 18 07:59:47.32: [32639]: <-- data [652]
Nov 18 07:59:47.47: [32639]: <-- data [2]
Nov 18 07:59:48.99: [32639]: --> [2:OK]
Nov 18 07:59:48.99: [32639]: <-- [9:AT+FRH=3\r]
Nov 18 07:59:49.49: [32639]: --> [7:CONNECT]
Nov 18 07:59:50.45: [32639]: --> HDLC<5:FF C8 21 57 BE>
Nov 18 07:59:50.45: [32639]: --> [2:OK]
Nov 18 07:59:50.45: [32639]: TRAINING succeeded
Nov 18 07:59:50.45: [32639]: DELAY 75 ms
Nov 18 07:59:50.52: [32639]: <-- [11:AT+FTM=146\r]
Nov 18 07:59:50.71: [32639]: --> [7:CONNECT]
Nov 18 07:59:50.71: [32639]: SEND begin page
Nov 18 07:59:50.71: [32639]: <-- data [1031]
Nov 18 07:59:50.71: [32639]: <-- data [1024]
[...]
Nov 18 08:01:08.76: [32639]: SENT 144604 bytes of data
Nov 18 08:01:08.76: [32639]: SEND 1D RTC
Nov 18 08:01:08.76: [32639]: <-- data [29]
Nov 18 08:01:08.99: [32639]: <-- data [2]
Nov 18 08:01:09.01: [32639]: SEND end page
Nov 18 08:01:11.23: [32639]: --> [2:OK]
Nov 18 08:01:11.23: [32639]: <-- [9:AT+FTS=9\r]
Nov 18 08:01:11.33: [32639]: --> [2:OK]
Nov 18 08:01:11.33: [32639]: SEND send EOP (no more pages or documents)
Nov 18 08:01:11.33: [32639]: <-- [9:AT+FTH=3\r]
Nov 18 08:01:11.40: [32639]: --> [7:CONNECT]
Nov 18 08:01:11.40: [32639]: <-- HDLC<3:FF C8 F4>
Nov 18 08:01:11.40: [32639]: <-- data [3]
Nov 18 08:01:11.40: [32639]: <-- data [2]
Nov 18 08:01:12.64: [32639]: --> [2:OK]
Nov 18 08:01:12.64: [32639]: <-- [9:AT+FRH=3\r]
Nov 18 08:01:13.01: [32639]: --> [7:CONNECT]
Nov 18 08:01:13.97: [32639]: --> HDLC<5:FF C8 31 45 8F>
Nov 18 08:01:13.97: [32639]: --> [2:OK]
Nov 18 08:01:13.97: [32639]: SEND recv MCF (message confirmation)
Nov 18 08:01:13.97: [32639]: SEND FAX (00017878): FROM root@xxxxxxxxxxxxxx TO 
07117880537 (page 1 of 1 sent in 1:30)
Nov 18 08:01:13.97: [32639]: SEND FAX (00017878): FROM root@xxxxxxxxxxxxxx TO 
07117880537 (docq/doc12002.ps;00 sent in 1:30)
Nov 18 08:01:13.97: [32639]: <-- [9:AT+FTH=3\r]
Nov 18 08:01:14.12: [32639]: --> [7:CONNECT]
Nov 18 08:01:14.12: [32639]: <-- HDLC<3:FF C8 DF>
Nov 18 08:01:14.12: [32639]: <-- data [3]
Nov 18 08:01:14.12: [32639]: <-- data [2]
Nov 18 08:01:15.37: [32639]: --> [2:OK]
Nov 18 08:01:15.37: [32639]: MODEM input buffering enabled
Nov 18 08:01:15.37: [32639]: <-- [5:ATH0\r]
Nov 18 08:01:15.67: [32639]: --> [2:OK]
Nov 18 08:01:15.67: [32639]: MODEM set DTR OFF
Nov 18 08:01:15.68: [32639]: SESSION END

I have also contacted the manufacturer of this modem 
Devolo was ELSA in former times.



- -- 
HAGOS eG                 phone: +49 711 7880592
Matthias Reich             fax: +49 711 7880535
Industriestr. 62           web: http://www.hagos.de
D-70565 Stuttgart         mail: rei@xxxxxxxx
Germany
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.4 (GNU/Linux)

iD8DBQFBnFi8cjMVLPQ5oUkRAhhzAJ47ezj8aQRDBXyHeDQH60JMWMpqdACdFB8N
xYcju9biJgJgmiE6DReAy28=
=dTfz
-----END PGP SIGNATURE-----

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*