[hylafax-users] I need a config file for my modem!!

[Kónya Balázs <b.konya@xxxxxxxxxxx>]

Hi everyone!

 

I  need a perfect config file for my Zyxel OMNI 56K faxmodem..

I tried out every chance (Class2 & Class1, rtscts & xonxoff, 19200 & 38400), everything!

However, I get all kinds of error:

-Unspecified Phase C error.. and B..

-Failure to train remote modem at 2400 bps or minimum speed

-Invalid dialing command

 

And I cannot fix these problems!?

Please, Somebody help me!! :\

 

My present config file:

 

CountryCode:                     36

AreaCode:              1

FAXNumber:                     ***********

LongDistancePrefix:            06

InternationalPrefix:  00

DialStringRules:       etc/dialrules

#ServerTracing:                  0x08501

ServerTracing:                    0xFFF

SessionTracing:                   0x08501

RecvFileMode:                   0644

LogFileMode:                     0640

DeviceMode:                      0660

RingsBeforeAnswer:           1

SpeakerVolume:                 off

GettyArgs:              "-r -b %l"

PriorityScheduling:  yes

TagLineFormat:                  "From %%l|%c|Page %%P of %%T"

MaxRecvPages:                  50

 

ModemType:                      Class2             # use this to supply a hint

ModemRate:                      19200              # max rate for DCE-DTE communication

#ModemFlowControl:        xonxoff            # XON/XOFF flow control assumed

ModemFlowControl:          rtscts               

#ModemSetupDTRCmd:    AT&D2                       # setup so DTR drop resets modem

#ModemSetupDCDCmd:   AT&C1                       # setup so DCD reflects carrier (or not)

 

#

#ModemResetCmds:                      ""                     # stuff to do when modem is reset

#ModemAnswerCmd:                    ATA                # use this to answer phone

#ModemNoFlowCmd:                   AT&K             # disable flow control cmd

#ModemHardFlowCmd:    AT&K3                      # hardware flow control cmd

#ModemSoftFlowCmd:      AT&K4                      # software flow control cmd

#ModemNoAutoAnswerCmd:       ATS0=0                      # disable auto-answer

#

# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.

# Note that we both turn the speaker on/off and set volume.

#

#ModemSetVolumeCmd:   "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"

#ModemEchoOffCmd:       ATE0              # disable command echo

#ModemVerboseResultsCmd:        ATV1              # enable verbose command results

#ModemResultCodesCmd: ATQ0              # enable result codes

#ModemOnHookCmd:                  ATH0              # place phone on hook (hangup)

#ModemSoftResetCmd:     ATZ                # do soft reset of modem

#ModemSoftResetCmdDelay:        3000    # pause after soft reset

#ModemWaitTimeCmd:     ATS7=60                    # wait 60 seconds for carrier

#ModemCommaPauseTimeCmd:   ATS8=2                      # comma pause time is 2 seconds

#ModemRecvFillOrder:      LSB2MSB                  # bit order of received facsimile

#ModemSendFillOrder:      LSB2MSB                  # bit order modem expects for transmit

#

# Configuration parameters for Class 2 modems.

#

Class2Cmd:                        AT+FCLASS=2         # command to enter class 2

Class2BORCmd:                AT+FBOR=0  # bit order for phase B/C/D (direct)

Class2RELCmd:                 AT+FREL=1   # byte-align EOL codes on recv

Class2CQCmd:                  ""                     # commands to enable copy quality proc.

Class2AbortCmd:               AT+FK                       # abort session command

Class2CQQueryCmd:        AT+FCQ=?    # query for copy quality capabilities

Class2DCCQueryCmd:      AT+FDCC=?  # query for modem capabilities

Class2TBCCmd:                AT+FTBC=0  # setup stream mode

Class2CRCmd:                  AT+FCR=1     # enable capability to receive

Class2PHCTOCmd:                      AT+FPHCTO=30       # set phase C timeout parameter

Class2BUGCmd:                AT+FBUG=1  # enable HDLC frame tracing

Class2LIDCmd:                 AT+FLID                    # set local identifier command

Class2DCCCmd:               AT+FDCC                  # set modem capabilities command

Class2DISCmd:                 AT+FDIS                    # set session parameters command

Class2DDISCmd:               ""                     # disable pre-dial DIS command hack

Class2CIGCmd:                 AT+FCIG                   # set polling identifier command

Class2PTSCmd:                 AT+FPTS                   # set post-page status command

Class2SPLCmd:                 AT+FSPL                   # set polling indicator command

#

# If Class2RecvDataTrigger is not set, then it is set to DC1

#

Class2RecvDataTrigger:     ""                     # character sent to modem to start recv

Class2XmitWaitForXON:  yes                   # if true, wait for XON before send

 

 

Thanks in advance!!

-Balazs