![]() |
Well, you are using Red Hat E3, and I think your libtiff is a good one (< 3.6.1), but it worth checking out. If it's >= 3.6.1, you should downgrade, see http://bugs.hylafax.org/bugzilla/show_bug.cgi?id=500 Otherwise, you must blame your USR firmware. --- Justin Rush <jrush@xxxxxxxxxxxxxx> wrote: > from my config file for ttyS1: > -- > # Modem-related stuff: should reflect modem command > interface > # and hardware connection/cabling (e.g. flow > control). > # > ModemType: Class1 # use class > 1 interface > ModemRate: 19200 # rate for > DCE-DTE communication > ModemFlowControl: xonxoff # software > flow control > # > ModemSetupDTRCmd: ATS13=1&D2 # setup so > DTR drop resets modem > ModemSetupDCDCmd: AT&C1 # setup so > DCD reflects carrier (or not) > ModemNoFlowCmd: AT&H0&I0&R1 # setup > modem for no flow control > ModemHardFlowCmd: AT&H1&I0&R2 # setup > modem for hardware flow control > ModemSoftFlowCmd: AT&H2&I2&R1 # setup > modem for software flow control > ModemResultCodesCmd: ATQ0X4 # enable > result codes > # > ModemMfrQueryCmd: !USR > ModemModelQueryCmd: ATI3 > ModemRevQueryCmd: ATI7 # XXX > returns a multi-line result > # > # When AT+FCLASS=1 is issued the modem automatically > switches > # to software flow control; these parameters let the > fax software > # reset flow control as needed after entering Class > 1. > # > Class1NFLOCmd: AT&H0&I0&R1 # setup > modem for no flow control > Class1HFLOCmd: AT&H1&I0&R2 # setup > modem for hardware flow control > Class1SFLOCmd: "" # modem does > this automatically > # > # This should resolve "DIS/DTC received 3 times" > errors: > # > Class1ResponseWaitCmd: AT+FRS=1 # wait after > sending TCF for response > # > # The remainder of this configuration is included so > that the > # modem "idles" in Class 0 while not sending or > receiving facsimile. > # > ModemSetupAACmd: AT+FCLASS=0 # leave > modem idling in class 0 > ModemAnswerCmd: AT+FCLASS=1A # answer in > Class 1 > # > # Disables the reporting of bad frames by the modem. > This > # overcomes a firmware problem in the x2 and V90 > Sportsters. > # It is not necessary for the Courier modem. > # > Class2NRCmd: AT+FNR=1,1,1,0 > -- > The modem is an old USR Courrier modem. It seems > that the modem is receiving the fax properly but the > internals of hylafax just aren't handling the fax > properly. > > Anything else I can check? > > Thanks, > Justin > > > On Mon, Sep 13, 2004 at 11:50:17AM -0700, Pedro > Rocadas wrote: > > Did you configured your modem in CLass1? What is > the > > value of ModemFlowControl in your config.ttyS1 > file? > > if it's not xonxoff try it. Other thing, you are > using > > a USR modem so, I definittly recommend you hylafax > > 4.2.0, but if you want a better advice, throw away > > that USR and buy a Multitech or a Zoom modem. > > > > --- Justin Rush <jrush@xxxxxxxxxxxxxx> wrote: > > > > > Hello, > > > I am having a problem receiving multiple pages > > > using hylafax. The logs show that multiple > pages > > > were transmitted, however the resulting tif that > is > > > generated only has one page. > > > > > > Sep 13 11:56:23 fromage FaxGetty[12548]: ANSWER: > FAX > > > CONNECTION DEVICE '/dev/ttyS1' > > > Sep 13 11:56:58 fromage FaxGetty[12548]: RECV > FAX > > > (000000074): from , page 1 in 0:27, INF, 3.85 > > > line/mm, 2-D MMR, 9600 bit/s > > > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV > FAX > > > (000000074): from , page 2 in 0:30, INF, 3.85 > > > line/mm, 2-D MMR, 9600 bit/s > > > Sep 13 11:57:28 fromage FaxGetty[12548]: RECV > FAX > > > (000000074): recvq/fax000000046.tif from , route > to > > > <unspecified>, 2 pages in 1:05 > > > Sep 13 11:57:30 fromage FaxGetty[12548]: RECV > FAX: > > > bin/faxrcvd "recvq/fax000000046.tif" "ttyS1" > > > "000000074" "" "" "" > > > Sep 13 11:57:42 fromage FaxGetty[12548]: MODEM > USR > > > 00:00:00/Configuration Profile... Product type > > > > US/Canada External Options > > > HST,V32bis,Terbo,V.FC,V.34 Fax Options > > > > Class 1/Class 2.0 Clock Freq > 20.16Mhz > > > Eprom 256k Ram > > > > 32k Supervisor date 12/02/94 DSP date > > > > 12/02/94 Supervisor rev 6.0.5 DSP > rev > > > 1.0.6 > > > > > > And from the xferfaxlog: > > > 09/13/04 11:56 RECV 000000074 ttyS1 > > > > "" fax "+1.###.###.####" "" > > > > 2220056 2 1:05 1:05 "" "" > "" > > > "" > > > (I put #'s over the number) > > > > > > I am currently using hylafax-4.1.8-1rh3 on > RedHat > > > Enterprise Linux v3.0 > > > What could be causing this problem? > > > If more information is needed, please tell me > what > > > and I will post it. > > > > > > Thanks in advance, > > > Justin Rush > > > Internet Scout Project > > > jrush@xxxxxxxxxxxxxx > > > > > > ____________________ HylaFAX(tm) Users Mailing > List > > > _______________________ > > > To subscribe/unsubscribe, click > > > http://lists.hylafax.org/cgi-bin/lsg2.cgi > > > On UNIX: mail -s unsubscribe > > > hylafax-users-request@xxxxxxxxxxx < /dev/null > > > *To learn about commercial HylaFAX(tm) > support, > > > mail sales@xxxxxxxxx* > > > > > > > > > > > > > > > > > > __________________________________ > > Do you Yahoo!? > > New and Improved Yahoo! Mail - 100MB free storage! > > http://promotions.yahoo.com/new_mail > > ____________________ HylaFAX(tm) Users Mailing List > _______________________ > To subscribe/unsubscribe, click > http://lists.hylafax.org/cgi-bin/lsg2.cgi > On UNIX: mail -s unsubscribe > hylafax-users-request@xxxxxxxxxxx < /dev/null > *To learn about commercial HylaFAX(tm) support, > mail sales@xxxxxxxxx* > > __________________________________ Do you Yahoo!? Yahoo! Mail is new and improved - Check it out! http://promotions.yahoo.com/new_mail ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*