Re: [hylafax-users] mail fax as pdf

[Pedro Rocadas <procadas@xxxxxxxxx>]

You are using SuSE rpms and I'm using HylaFAX sources.
You must expect differences...check path, dirs and
files.

--- rasmus.stokholm@xxxxxxxxxxxxx wrote:

> I get
> 
> 		An attempt to receive facsimile on ttyS1 failed
> because:
> 
> 
> 
> 		---- Transcript of session follows ----
> 
> 		No transcript available (CommID clog/c00000001).
> 
> If I then remove log/c so it only says 00000001
> 
> I get	
> 
> An attempt to receive facsimile on ttyS1 failed
> because:
> 
> 
> 
> ---- Transcript of session follows ----
> 
> Sep 07 13:47:50.48: [ 4814]: SESSION BEGIN 00000001
> 0033324704
> Sep 07 13:47:50.48: [ 4814]: HylaFAX (tm) Version
> 4.1.8
> Sep 07 13:47:50.48: [ 4814]: <-- [4:ATA\r]
> Sep 07 13:47:56.50: [ 4814]: --> [7:CONNECT]
> Sep 07 13:47:56.50: [ 4814]: ANSWER: FAX CONNECTION
> DEVICE '/dev/ttyS1'
> Sep 07 13:47:56.50: [ 4814]: RECV FAX: begin
> Sep 07 13:47:56.50: [ 4814]: RECV FAX: CDPN 
> Sep 07 13:47:58.18: [ 4814]: --> [7:CONNECT]
> Sep 07 13:47:58.73: [ 4814]: --> [2:OK]
> Sep 07 13:47:58.73: [ 4814]: <-- [9:AT+FRH=3\r]
> Sep 07 13:47:59.40: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:00.74: [ 4814]: --> [2:OK]
> Sep 07 13:48:00.74: [ 4814]: REMOTE TSI "+45
> 33667034"
> Sep 07 13:48:00.74: [ 4814]: <-- [9:AT+FRH=3\r]
> Sep 07 13:48:00.75: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:01.04: [ 4814]: --> [2:OK]
> Sep 07 13:48:01.04: [ 4814]: REMOTE wants 9600 bit/s
> Sep 07 13:48:01.04: [ 4814]: REMOTE wants page width
> 1728 pixels in 215
> mm
> Sep 07 13:48:01.04: [ 4814]: REMOTE wants unlimited
> page length
> Sep 07 13:48:01.04: [ 4814]: REMOTE wants 3.85
> line/mm
> Sep 07 13:48:01.04: [ 4814]: REMOTE wants 2-D MR
> Sep 07 13:48:01.04: [ 4814]: RECV training at v.29
> 9600 bit/s
> Sep 07 13:48:01.04: [ 4814]: <-- [10:AT+FRM=96\r]
> Sep 07 13:48:01.41: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:03.00: [ 4814]: RECV: TCF 1884 bytes,
> 2% non-zero, 1835
> zero-run
> Sep 07 13:48:03.01: [ 4814]: --> [10:NO CARRIER]
> Sep 07 13:48:03.01: [ 4814]: DELAY 75 ms
> Sep 07 13:48:03.08: [ 4814]: TRAINING succeeded
> Sep 07 13:48:03.08: [ 4814]: <-- [9:AT+FTH=3\r]
> Sep 07 13:48:03.13: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:04.44: [ 4814]: --> [2:OK]
> Sep 07 13:48:04.44: [ 4814]: <-- [10:AT+FRM=96\r]
> Sep 07 13:48:05.18: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:05.18: [ 4814]: RECV: begin page
> Sep 07 13:48:12.49: [ 4814]: RECV: 1126 total lines,
> 0 bad lines, 0
> consecutive 
> bad lines
> Sep 07 13:48:12.49: [ 4814]: RECV: end page
> Sep 07 13:48:12.49: [ 4814]: --> [10:NO CARRIER]
> Sep 07 13:48:12.49: [ 4814]: <-- [9:AT+FRH=3\r]
> Sep 07 13:48:12.88: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:13.52: [ 4814]: --> [2:OK]
> Sep 07 13:48:13.52: [ 4814]: RECV recv EOP (no more
> pages or documents)
> Sep 07 13:48:13.52: [ 4814]: <-- [9:AT+FRS=7\r]
> Sep 07 13:48:13.64: [ 4814]: --> [2:OK]
> Sep 07 13:48:13.64: [ 4814]: <-- [9:AT+FTH=3\r]
> Sep 07 13:48:13.69: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:15.00: [ 4814]: --> [2:OK]
> Sep 07 13:48:15.00: [ 4814]: RECV send MCF (message
> confirmation)
> Sep 07 13:48:15.00: [ 4814]: RECV FAX (00000001):
> from +45 33667034,
> page 1 in 
> 0:12, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
> Sep 07 13:48:15.00: [ 4814]: RECV FAX (00000001):
> recvq/fax00001.tif
> from +45 
> 33667034, route to <unspecified>, 1 pages in 0:19
> Sep 07 13:48:15.00: [ 4814]: <-- [9:AT+FRH=3\r]
> Sep 07 13:48:15.64: [ 4814]: --> [7:CONNECT]
> Sep 07 13:48:16.47: [ 4814]: --> [2:OK]
> Sep 07 13:48:16.47: [ 4814]: RECV FAX: bin/faxrcvd
> "recvq/fax00001.tif"
> "ttyS1" 
> "00000001" "" "" "" ""
> Sep 07 13:48:16.54: [ 4814]: RECV FAX: end
> Sep 07 13:48:16.54: [ 4814]: SESSION END
> 
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf
> Of Pedro Rocadas
> Sent: 9. september 2004 15:33
> To: hylafax-users@xxxxxxxxxxx
> Subject: Re: [hylafax-users] mail fax as pdf
> 
> Go to /var/spool/fax (?)
> 
> Run faxrcvd like this:
> 
> bin/faxrcvd recvq/fax00001.tif ttyS1 log/c00000001
> ""
> ""
> 
> Be SURE that in the etc/FaxDispatch file you have
> correspondance betwen your device and the username
> 
> ttyS1) SENDTO=procadas@domain;; FILETYPE=pdf;;
>  
> --- rasmus.stokholm@xxxxxxxxxxxxx wrote:
> 
> > How do I run it from the shell
> > 
> > I get a mail: Facsmilie not received.
> > 
> > I'm in /var/spool/fax/
> > And type: /var/spool/fax/bin/faxrcvd fax00001.tif
> > ttyS1 00000001 ""
> > 
> > -----Original Message-----
> > From: hylafax-users-bounce@xxxxxxxxxxx
> > [mailto:hylafax-users-bounce@xxxxxxxxxxx] On
> Behalf
> > Of Pedro Rocadas
> > Sent: 9. september 2004 15:04
> > To: hylafax-users@xxxxxxxxxxx
> > Subject: Re: [hylafax-users] mail fax as pdf
> > 
> > Did you created FaxDispatch?
> > other way to see what could be wrong is running
> > faxrcvd from the shell.
> > 
> > --- rasmus.stokholm@xxxxxxxxxxxxx wrote:
> > 
> > > Still doesn't work,
> > > Ok last resort, can you take a look at my files
> > and
> > > see if there is any
> > > thing wrong.
> > > 
> > > I'm not quite sure where the file should be
> > > attached.
> > > Maybe it is missing?
> > > 
> > > 
> > > # FaxDispatch
> > > # Dispatch fax to email depending on own MSN or
> > > extention (ISDN lines) #
> > > sourced from faxrcvd # if [ "$7" != "" ]; then
> > >     PHONEMATCH=$7$
> > >     USERENTRY=`grep -v "^#" etc/users | grep
> > > "$PHONEMATCH"`
> > >     if [ "$USERENTRY" != "" ]; then
> > > 	USERNAME=`echo $USERENTRY | awk '{print $1}'`
> > > 	FILETYPE=pdf
> > > 	SENDTO="$USERNAME"
> > > ;;
> > >     fi
> > > fi
> > > 
> > > 
> > > 
> > > #
> > > # faxrcvd file devID commID error-msg
> > > #
> > > if [ $# -lt 4 ]; then
> > >     echo "Usage: $0 file devID commID error-msg
> > > [CIDNumber] [CIDName]
> > > [destination]"
> > >     exit 1
> > > fi
> > > 
> > > test -f etc/setup.cache || {
> > >     SPOOL=`pwd`
> > >     cat<<EOF
> > > 
> > > FATAL ERROR: $SPOOL/etc/setup.cache is missing!
> > > 
> > > The file $SPOOL/etc/setup.cache is not present. 
> > > This
> > > probably means the machine has not been setup
> > using
> > > the faxsetup(8C)
> > > command.  Read the documentation on setting up
> > > HylaFAX before you
> > > startup a server system.
> 
=== message truncated ===



		
__________________________________
Do you Yahoo!?
Yahoo! Mail Address AutoComplete - You start. We finish.
http://promotions.yahoo.com/new_mail 

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*