Re: [hylafax-users] mail fax as pdf

[<rasmus.stokholm@xxxxxxxxxxxxx>]

I get

		An attempt to receive facsimile on ttyS1 failed because:



		---- Transcript of session follows ----

		No transcript available (CommID clog/c00000001).

If I then remove log/c so it only says 00000001

I get	

An attempt to receive facsimile on ttyS1 failed because:



---- Transcript of session follows ----

Sep 07 13:47:50.48: [ 4814]: SESSION BEGIN 00000001 0033324704
Sep 07 13:47:50.48: [ 4814]: HylaFAX (tm) Version 4.1.8
Sep 07 13:47:50.48: [ 4814]: <-- [4:ATA\r]
Sep 07 13:47:56.50: [ 4814]: --> [7:CONNECT]
Sep 07 13:47:56.50: [ 4814]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS1'
Sep 07 13:47:56.50: [ 4814]: RECV FAX: begin
Sep 07 13:47:56.50: [ 4814]: RECV FAX: CDPN 
Sep 07 13:47:58.18: [ 4814]: --> [7:CONNECT]
Sep 07 13:47:58.73: [ 4814]: --> [2:OK]
Sep 07 13:47:58.73: [ 4814]: <-- [9:AT+FRH=3\r]
Sep 07 13:47:59.40: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:00.74: [ 4814]: --> [2:OK]
Sep 07 13:48:00.74: [ 4814]: REMOTE TSI "+45 33667034"
Sep 07 13:48:00.74: [ 4814]: <-- [9:AT+FRH=3\r]
Sep 07 13:48:00.75: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:01.04: [ 4814]: --> [2:OK]
Sep 07 13:48:01.04: [ 4814]: REMOTE wants 9600 bit/s
Sep 07 13:48:01.04: [ 4814]: REMOTE wants page width 1728 pixels in 215
mm
Sep 07 13:48:01.04: [ 4814]: REMOTE wants unlimited page length
Sep 07 13:48:01.04: [ 4814]: REMOTE wants 3.85 line/mm
Sep 07 13:48:01.04: [ 4814]: REMOTE wants 2-D MR
Sep 07 13:48:01.04: [ 4814]: RECV training at v.29 9600 bit/s
Sep 07 13:48:01.04: [ 4814]: <-- [10:AT+FRM=96\r]
Sep 07 13:48:01.41: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:03.00: [ 4814]: RECV: TCF 1884 bytes, 2% non-zero, 1835
zero-run
Sep 07 13:48:03.01: [ 4814]: --> [10:NO CARRIER]
Sep 07 13:48:03.01: [ 4814]: DELAY 75 ms
Sep 07 13:48:03.08: [ 4814]: TRAINING succeeded
Sep 07 13:48:03.08: [ 4814]: <-- [9:AT+FTH=3\r]
Sep 07 13:48:03.13: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:04.44: [ 4814]: --> [2:OK]
Sep 07 13:48:04.44: [ 4814]: <-- [10:AT+FRM=96\r]
Sep 07 13:48:05.18: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:05.18: [ 4814]: RECV: begin page
Sep 07 13:48:12.49: [ 4814]: RECV: 1126 total lines, 0 bad lines, 0
consecutive 
bad lines
Sep 07 13:48:12.49: [ 4814]: RECV: end page
Sep 07 13:48:12.49: [ 4814]: --> [10:NO CARRIER]
Sep 07 13:48:12.49: [ 4814]: <-- [9:AT+FRH=3\r]
Sep 07 13:48:12.88: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:13.52: [ 4814]: --> [2:OK]
Sep 07 13:48:13.52: [ 4814]: RECV recv EOP (no more pages or documents)
Sep 07 13:48:13.52: [ 4814]: <-- [9:AT+FRS=7\r]
Sep 07 13:48:13.64: [ 4814]: --> [2:OK]
Sep 07 13:48:13.64: [ 4814]: <-- [9:AT+FTH=3\r]
Sep 07 13:48:13.69: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:15.00: [ 4814]: --> [2:OK]
Sep 07 13:48:15.00: [ 4814]: RECV send MCF (message confirmation)
Sep 07 13:48:15.00: [ 4814]: RECV FAX (00000001): from +45 33667034,
page 1 in 
0:12, INF, 3.85 line/mm, 2-D MR, 9600 bit/s
Sep 07 13:48:15.00: [ 4814]: RECV FAX (00000001): recvq/fax00001.tif
from +45 
33667034, route to <unspecified>, 1 pages in 0:19
Sep 07 13:48:15.00: [ 4814]: <-- [9:AT+FRH=3\r]
Sep 07 13:48:15.64: [ 4814]: --> [7:CONNECT]
Sep 07 13:48:16.47: [ 4814]: --> [2:OK]
Sep 07 13:48:16.47: [ 4814]: RECV FAX: bin/faxrcvd "recvq/fax00001.tif"
"ttyS1" 
"00000001" "" "" "" ""
Sep 07 13:48:16.54: [ 4814]: RECV FAX: end
Sep 07 13:48:16.54: [ 4814]: SESSION END

-----Original Message-----
From: hylafax-users-bounce@xxxxxxxxxxx
[mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf Of Pedro Rocadas
Sent: 9. september 2004 15:33
To: hylafax-users@xxxxxxxxxxx
Subject: Re: [hylafax-users] mail fax as pdf

Go to /var/spool/fax (?)

Run faxrcvd like this:

bin/faxrcvd recvq/fax00001.tif ttyS1 log/c00000001 ""
""

Be SURE that in the etc/FaxDispatch file you have
correspondance betwen your device and the username

ttyS1) SENDTO=procadas@domain;; FILETYPE=pdf;;
 
--- rasmus.stokholm@xxxxxxxxxxxxx wrote:

> How do I run it from the shell
> 
> I get a mail: Facsmilie not received.
> 
> I'm in /var/spool/fax/
> And type: /var/spool/fax/bin/faxrcvd fax00001.tif
> ttyS1 00000001 ""
> 
> -----Original Message-----
> From: hylafax-users-bounce@xxxxxxxxxxx
> [mailto:hylafax-users-bounce@xxxxxxxxxxx] On Behalf
> Of Pedro Rocadas
> Sent: 9. september 2004 15:04
> To: hylafax-users@xxxxxxxxxxx
> Subject: Re: [hylafax-users] mail fax as pdf
> 
> Did you created FaxDispatch?
> other way to see what could be wrong is running
> faxrcvd from the shell.
> 
> --- rasmus.stokholm@xxxxxxxxxxxxx wrote:
> 
> > Still doesn't work,
> > Ok last resort, can you take a look at my files
> and
> > see if there is any
> > thing wrong.
> > 
> > I'm not quite sure where the file should be
> > attached.
> > Maybe it is missing?
> > 
> > 
> > # FaxDispatch
> > # Dispatch fax to email depending on own MSN or
> > extention (ISDN lines) #
> > sourced from faxrcvd # if [ "$7" != "" ]; then
> >     PHONEMATCH=$7$
> >     USERENTRY=`grep -v "^#" etc/users | grep
> > "$PHONEMATCH"`
> >     if [ "$USERENTRY" != "" ]; then
> > 	USERNAME=`echo $USERENTRY | awk '{print $1}'`
> > 	FILETYPE=pdf
> > 	SENDTO="$USERNAME"
> > ;;
> >     fi
> > fi
> > 
> > 
> > 
> > #
> > # faxrcvd file devID commID error-msg
> > #
> > if [ $# -lt 4 ]; then
> >     echo "Usage: $0 file devID commID error-msg
> > [CIDNumber] [CIDName]
> > [destination]"
> >     exit 1
> > fi
> > 
> > test -f etc/setup.cache || {
> >     SPOOL=`pwd`
> >     cat<<EOF
> > 
> > FATAL ERROR: $SPOOL/etc/setup.cache is missing!
> > 
> > The file $SPOOL/etc/setup.cache is not present. 
> > This
> > probably means the machine has not been setup
> using
> > the faxsetup(8C)
> > command.  Read the documentation on setting up
> > HylaFAX before you
> > startup a server system.
> > 
> > EOF
> >     exit 1
> > }
> > . etc/setup.cache
> > 
> > INFO=$SBIN/faxinfo
> > FAX2PS=$TIFFBIN/fax2ps
> > MIMENCODE=mimencode
> > ENCODING=base64
> > TIFF2PS=tiff2ps
> > PS2PDF=ps2pdf
> > TOADDR=FaxMaster
> > TIFFINFO=tiffinfo
> > NOTIFY_FAXMASTER=always
> > 
> > #
> > # wraper for base64 encoding
> > #
> > # first try uuencode if it is not installed
> fallback
> > to
> > # metamails mimencode if it is also not installed
> > give an
> > # error message
> > #
> > function base64 {
> > 
> >     if [ -x /usr/bin/uuencode ]; then
> >         /usr/bin/uuencode -m $1 $1 | /usr/bin/sed
> > '1d;$d'
> >     elif [ -x /usr/bin/mimencode ]; then
> >         /usr/bin/mimencode $1
> >     else
> >         echo "Error: No encoder for base64 found."
> >         echo "Please install sharutils or
> metamail."
> >     fi
> > }
> > 
> > #
> > # Permit various types of attachment types: ps,
> tif,
> > pdf
> > # Note that non-ASCII filetypes require sharutils
> or
> > metamail. # pdf
> > requires tiff2ps and ps2pdf # FILETYPE=pdf
> > 
> > #
> > # There is no good portable way to find out the
> > fully qualified # domain
> > name (FQDN) of the host or the TCP port for the
> > hylafax # service so we
> > fudge here.  Folks may want to tailor this to #
> > their needs; e.g. add a
> > domain or use localhost so the loopback #
> interface
> > is used. #
> > HOSTNAME=`hostname`			# XXX no good way to find
> FQDN
> > PORT=4559				# XXX no good way to lookup
> > service
> > 
> > FILE="$1"
> > DEVICE="$2"
> > COMMID="$3"
> > MSG="$4"
> > CIDNUMBER="$5"
> > CIDNAME="$6"
> > 
> > FILENAME=`echo $FILE | $SED -e 's/.tif//' -e
> > 's/recvq///'`
> > 
> > if [ -f $FILE ]; then
> >     #
> >     # Check the sender's TSI and setup to dispatch
> >     # facsimile received from well-known senders.
> >     #
> >     SUBADDR="`$INFO $FILE | $AWK -F: '/SubAddr/ {
> > print $2 }'
> > 2>/dev/null`"
> >     SENDER="`$INFO $FILE | $AWK -F: '/Sender/ {
> > print $2 }'
> > 2>/dev/null`"
> >     SENDTO=
> >     if [ -f bin/FaxDispatch ]; then
> > 	. bin/FaxDispatch	# NB: FaxDispatch sets SENDTO
> > based on
> > $7
> >     fi
> >     #
> >     # Don't send FaxMaster duplicates, and
> FaxMaster
> > may not even
> >     # want a message at all, depending on
> > NOTIFY_FAXMASTER.
> >     #
> >     case $NOTIFY_FAXMASTER$MSG in
> > 	never*)		NOTIFY_FAXMASTER=no;;
> > 	errors)		NOTIFY_FAXMASTER=no;;
> > 	*)		NOTIFY_FAXMASTER=yes;;
> >     esac
> >     if [ "$TOADDR" != "$SENDTO" -a
> > "$NOTIFY_FAXMASTER" != "no" ]; then
> > 	(echo "To: $TOADDR"
> > 	 echo "From: The HylaFAX Receive Agent <fax>"
> > 	 echo "Subject: Facsimile received from $SENDER";
> > 	 echo ""
> > 	 echo "$FILE (ftp://$HOSTNAME:$PORT/$FILE):";
> $INFO
> > -n $FILE
> > 	echo "ReceivedOn: $DEVICE"
> > 	if [ "$MSG" ]; then
> > 	    echo ""
> > 	    echo "The full document was not received
> > because:"
> > 	    echo ""
> > 	    echo "    $MSG"
> > 	    echo ""
> > 	    echo "    ---- Transcript of session follows
> > ----"
> > 	    echo ""
> > 	    if [ -f log/c$COMMID ]; then
> > 		$SED -e '/-- data/d' 
> > 		 -e '/start.*timer/d' -e '/stop.*timer/d' 
> > 		 log/c$COMMID
> 
=== message truncated ===


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 

____________________ HylaFAX(tm) Users Mailing List
_______________________
  To subscribe/unsubscribe, click
http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx <
/dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*



This message is for the designated recipient only and may contain privileged, proprietary, or otherwise private information.  If you have received it in error, please notify the sender immediately and delete the original.  Any other use of the email by you is prohibited.

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*