Re: [hylafax-users] Rockwell modem cards in Lucent TNT

[Tracy R Reed <treed@xxxxxxxxxxxxxxxxxxxxx>]

On Tue, Aug 24, 2004 at 02:26:12PM -0700, Lee Howard spake thusly:
> >Class1EOPWaitCmd:   <delay
> >Class1TCFWaitCmd:   <delay
> >Class1PPMWaitCmd:   <delay
> 
> faxaddmodem did this?  Anyway, remove these lines.

Yep! They are now removed.

> >Aug 24 13:33:27.04: [10680]: SESSION BEGIN 00011651 16196717023
> >Aug 24 13:33:27.04: [10680]: HylaFAX (tm) Version 4.1.8
> 
> Consider upgrading.  It isn't crucial to your problem, but it will help 
> out with a bit of error handling.

Ok. I installed it from source myself June 7th. Surprised it is out of
datealready given how stable hylafax is.

Attached is the current problem...

-- 
Tracy Reed                     The attachment is a digital signature.
http://copilotconsulting.com   More info: http://copilotconsulting.com/sig

Aug 24 14:30:16.02: [10844]: SESSION BEGIN 00011654 16196717023
Aug 24 14:30:16.02: [10844]: HylaFAX (tm) Version 4.1.8
Aug 24 14:30:16.02: [10844]: SEND FAX: JOB 17919 DEST 16196717023 COMMID 00011654 DEVICE '/dev/ttya0'
Aug 24 14:30:16.02: [10844]: MODEM set DTR OFF
Aug 24 14:30:16.02: [10844]: MODEM set baud rate: 0 baud (flow control unchanged)
Aug 24 14:30:16.02: [10844]: DELAY 75 ms
Aug 24 14:30:16.10: [10844]: MODEM set DTR ON
Aug 24 14:30:16.10: [10844]: DELAY 2600 ms
Aug 24 14:30:19.70: [10844]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Aug 24 14:30:19.70: [10844]: DELAY 10 ms
Aug 24 14:30:19.71: [10844]: MODEM flush i/o
Aug 24 14:30:19.71: [10844]: <-- [4:ATZ\r]
Aug 24 14:30:22.03: [10844]: --> [2:OK]
Aug 24 14:30:22.03: [10844]: DELAY 3000 ms
Aug 24 14:30:25.03: [10844]: <-- [5:ATE0\r]
Aug 24 14:30:25.33: [10844]: --> [4:ATE0]
Aug 24 14:30:25.33: [10844]: --> [2:OK]
Aug 24 14:30:25.33: [10844]: <-- [5:ATV1\r]
Aug 24 14:30:25.63: [10844]: --> [2:OK]
Aug 24 14:30:25.63: [10844]: <-- [5:ATQ0\r]
Aug 24 14:30:25.93: [10844]: --> [2:OK]
Aug 24 14:30:25.93: [10844]: <-- [7:ATS0=0\r]
Aug 24 14:30:26.23: [10844]: --> [2:OK]
Aug 24 14:30:26.23: [10844]: <-- [7:ATS8=2\r]
Aug 24 14:30:26.53: [10844]: --> [2:OK]
Aug 24 14:30:26.53: [10844]: <-- [8:ATS7=60\r]
Aug 24 14:30:26.83: [10844]: --> [2:OK]
Aug 24 14:30:26.83: [10844]: <-- [12:AT+FCLASS=1\r]
Aug 24 14:30:27.13: [10844]: --> [2:OK]
Aug 24 14:30:27.13: [10844]: <-- [7:ATL0M1\r]
Aug 24 14:30:27.43: [10844]: --> [2:OK]
Aug 24 14:30:27.43: [10844]: STATE CHANGE: RUNNING -> SENDING
Aug 24 14:30:27.43: [10844]: MODEM input buffering enabled
Aug 24 14:30:27.43: [10844]: <-- [12:AT+FCLASS=1\r]
Aug 24 14:30:27.83: [10844]: --> [2:OK]
Aug 24 14:30:27.83: [10844]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 24 14:30:27.83: [10844]: DIAL 16196717023
Aug 24 14:30:27.83: [10844]: <-- [16:ATDT16196717023\r]
Aug 24 14:30:42.34: [10844]: --> [7:CONNECT]
Aug 24 14:30:42.34: [10844]: MODEM input buffering disabled
Aug 24 14:30:43.44: [10844]: --> HDLC<16:FF C0 04 00 00 6A AA AA 00 01 09 01 00 00 50 DA>
Aug 24 14:30:43.44: [10844]: --> [2:OK]
Aug 24 14:30:43.44: [10844]: REMOTE NSF "00 00 56 55 55 00 80 90 80 00 00 0A"
Aug 24 14:30:43.44: [10844]: NSF remote fax equipment: Brother 
Aug 24 14:30:43.44: [10844]: <-- [9:AT+FRH=3\r]
Aug 24 14:30:43.64: [10844]: --> [7:CONNECT]
Aug 24 14:30:44.14: [10844]: --> HDLC<25:FF C0 02 CC 4C 0C EC 8C EC 6C 9C 8C 6C 8C 04 04 04 04 04 04 04 04 04 26 5B>
Aug 24 14:30:44.14: [10844]: --> [2:OK]
Aug 24 14:30:44.14: [10844]: REMOTE CSI "16196717023"
Aug 24 14:30:44.14: [10844]: <-- [9:AT+FRH=3\r]
Aug 24 14:30:44.34: [10844]: --> [7:CONNECT]
Aug 24 14:30:44.54: [10844]: --> HDLC<11:FF C8 01 00 72 1D 01 01 88 A9 FF>
Aug 24 14:30:44.54: [10844]: --> [2:OK]
Aug 24 14:30:44.54: [10844]: REMOTE best rate 9600 bit/s
Aug 24 14:30:44.54: [10844]: REMOTE max page width 1728 pixels in 215 mm
Aug 24 14:30:44.54: [10844]: REMOTE max unlimited page length
Aug 24 14:30:44.54: [10844]: REMOTE best vres 7.7 line/mm
Aug 24 14:30:44.54: [10844]: REMOTE best format 1-D MR
Aug 24 14:30:44.54: [10844]: REMOTE best 20 ms, 10 ms/scanline
Aug 24 14:30:44.54: [10844]: USE 9600 bit/s
Aug 24 14:30:44.54: [10844]: USE 20 ms, 10 ms/scanline
Aug 24 14:30:44.54: [10844]: SEND file "docq/doc41.tif;30"
Aug 24 14:30:44.54: [10844]: USE page width 1728 pixels in 215 mm
Aug 24 14:30:44.54: [10844]: USE unlimited page length
Aug 24 14:30:44.54: [10844]: USE 3.85 line/mm
Aug 24 14:30:44.54: [10844]: USE 1-D MR
Aug 24 14:30:44.54: [10844]: SEND training at v.29 9600 bit/s
Aug 24 14:30:44.54: [10844]: <-- [9:AT+FTH=3\r]
Aug 24 14:30:44.74: [10844]: --> [7:CONNECT]
Aug 24 14:30:44.74: [10844]: <-- HDLC<23:FF C0 C2 4C CC EC EC EC 4C EC 6C 6C 1C 04 04 04 04 04 04 04 04 04 04>
Aug 24 14:30:44.74: [10844]: <-- data [23]
Aug 24 14:30:44.74: [10844]: <-- data [2]
Aug 24 14:30:46.74: [10844]: --> [7:CONNECT]
Aug 24 14:30:46.74: [10844]: <-- HDLC<6:FF C8 C1 00 60 10>
Aug 24 14:30:46.74: [10844]: <-- data [6]
Aug 24 14:30:46.74: [10844]: <-- data [2]
Aug 24 14:30:47.24: [10844]: --> [2:OK]
Aug 24 14:30:47.24: [10844]: <-- [9:AT+FTS=7\r]
Aug 24 14:30:47.44: [10844]: --> [5:ERROR]
Aug 24 14:30:47.44: [10844]: MODEM Command error
Aug 24 14:30:47.44: [10844]: <-- [9:AT+FTH=3\r]
Aug 24 14:30:47.63: [10844]: --> [7:CONNECT]
Aug 24 14:30:47.64: [10844]: <-- HDLC<3:FF C8 DF>
Aug 24 14:30:47.64: [10844]: <-- data [3]
Aug 24 14:30:47.64: [10844]: <-- data [2]
Aug 24 14:30:49.04: [10844]: --> [2:OK]
Aug 24 14:30:49.04: [10844]: MODEM input buffering enabled
Aug 24 14:30:49.04: [10844]: SEND FAILED: JOB 17919 DEST 16196717023 ERR Stop and wait failure (modem on hook); too many attempts to dial
Aug 24 14:30:49.04: [10844]: <-- [5:ATH0\r]
Aug 24 14:30:50.94: [10844]: --> [2:OK]
Aug 24 14:30:50.94: [10844]: MODEM set DTR OFF
Aug 24 14:30:50.94: [10844]: MODEM set baud rate: 0 baud (flow control unchanged)
Aug 24 14:30:50.94: [10844]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Aug 24 14:30:50.94: [10844]: SESSION END

Attachment: pgp00015.pgp
Description: PGP signature