 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Problem in sending TCF
- To: hylafax-users@xxxxxxxxxxx
- Subject: [hylafax-users] Problem in sending TCF
- From: andrea.satriani@xxxxxx
- Date: Wed, 19 May 2004 12:06:45 +0200
Hi all, I ask you for help! Sending fax I have problem in sending TCF. This is log: mag 19 11:30:49.81: [25442]: SESSION BEGIN 00000135 1415400 mag 19 11:30:49.81: [25442]: HylaFAX (tm) Version 4.1.8 mag 19 11:30:49.81: [25442]: SEND FAX: JOB 6075 DEST 400 COMMID 00000135 DEVICE '/dev/ttyS0' mag 19 11:30:49.81: [25442]: MODEM set DTR OFF mag 19 11:30:49.81: [25442]: DELAY 75 ms mag 19 11:30:49.89: [25442]: MODEM set DTR ON mag 19 11:30:49.89: [25442]: DELAY 2600 ms mag 19 11:30:53.50: [25442]: MODEM set baud rate: 19200 baud, input flow RTS/CTS, output flow RTS/CTS mag 19 11:30:53.50: [25442]: DELAY 10 ms mag 19 11:30:53.51: [25442]: MODEM flush i/o mag 19 11:30:53.51: [25442]: <-- [4:ATZ\r] mag 19 11:30:53.67: [25442]: --> [2:OK] mag 19 11:30:53.67: [25442]: DELAY 3000 ms mag 19 11:30:56.67: [25442]: <-- [5:ATE0\r] mag 19 11:30:56.68: [25442]: --> [4:ATE0] mag 19 11:30:56.68: [25442]: --> [2:OK] mag 19 11:30:56.68: [25442]: <-- [5:ATV1\r] mag 19 11:30:56.69: [25442]: --> [2:OK] mag 19 11:30:56.69: [25442]: <-- [5:ATQ0\r] mag 19 11:30:56.70: [25442]: --> [2:OK] mag 19 11:30:56.70: [25442]: <-- [7:ATS0=0\r] mag 19 11:30:56.71: [25442]: --> [2:OK] mag 19 11:30:56.71: [25442]: <-- [7:ATS8=2\r] mag 19 11:30:56.72: [25442]: --> [2:OK] mag 19 11:30:56.72: [25442]: <-- [9:ATS7=120\r] mag 19 11:30:56.74: [25442]: --> [2:OK] mag 19 11:30:56.74: [25442]: <-- [12:AT+FCLASS=1\r] mag 19 11:30:56.76: [25442]: --> [2:OK] mag 19 11:30:56.76: [25442]: <-- [7:ATL0M1\r] mag 19 11:30:56.77: [25442]: --> [2:OK] mag 19 11:30:56.77: [25442]: STATE CHANGE: RUNNING -> SENDING mag 19 11:30:56.77: [25442]: MODEM input buffering enabled mag 19 11:30:56.77: [25442]: <-- [12:AT+FCLASS=1\r] mag 19 11:30:56.89: [25442]: --> [2:OK] mag 19 11:30:56.89: [25442]: DIAL 400 mag 19 11:30:56.89: [25442]: <-- [8:ATDT400\r] mag 19 11:31:09.68: [25442]: --> [7:CONNECT] mag 19 11:31:09.68: [25442]: MODEM input buffering disabled mag 19 11:31:09.68: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:10.73: [25442]: --> HDLC<25:FF C0 02 0C 0C 2C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 8D C4> mag 19 11:31:10.74: [25442]: --> [2:OK] mag 19 11:31:10.74: [25442]: REMOTE CSI "400" mag 19 11:31:10.74: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:31:10.76: [25442]: --> [7:CONNECT] mag 19 11:31:10.76: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:11.16: [25442]: --> HDLC<12:FF C8 01 00 76 5F 01 79 03 00 20 4D> mag 19 11:31:11.17: [25442]: --> [2:OK] mag 19 11:31:11.17: [25442]: REMOTE best rate 14400 bit/s mag 19 11:31:11.17: [25442]: REMOTE max page width 2432 pixels in 303 mm mag 19 11:31:11.17: [25442]: REMOTE max unlimited page length mag 19 11:31:11.17: [25442]: REMOTE best vres 7.7 line/mm mag 19 11:31:11.17: [25442]: REMOTE best format 1-D MR mag 19 11:31:11.17: [25442]: REMOTE best 0 ms/scanline mag 19 11:31:11.17: [25442]: USE 14400 bit/s mag 19 11:31:11.17: [25442]: USE 0 ms/scanline mag 19 11:31:11.17: [25442]: SEND file "docq/doc6075.cover;30" mag 19 11:31:11.17: [25442]: USE page width 1728 pixels in 215 mm mag 19 11:31:11.17: [25442]: USE unlimited page length mag 19 11:31:11.17: [25442]: USE 3.85 line/mm mag 19 11:31:11.17: [25442]: USE 1-D MR mag 19 11:31:11.17: [25442]: SEND training at v.17 14400 bit/s mag 19 11:31:11.17: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:31:11.22: [25442]: --> [7:CONNECT] mag 19 11:31:11.22: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:31:11.22: [25442]: <-- data [23] mag 19 11:31:11.22: [25442]: <-- data [2] mag 19 11:31:13.01: [25442]: --> [7:CONNECT] mag 19 11:31:13.01: [25442]: <-- HDLC<6:FF C8 C1 00 44 1E> mag 19 11:31:13.01: [25442]: <-- data [6] mag 19 11:31:13.01: [25442]: <-- data [2] mag 19 11:31:13.45: [25442]: --> [2:OK] mag 19 11:31:13.45: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:31:13.54: [25442]: --> [2:OK] mag 19 11:31:13.54: [25442]: <-- [11:AT+FTM=145\r] mag 19 11:31:13.58: [25442]: --> [7:CONNECT] mag 19 11:31:13.58: [25442]: <-- data [1024] mag 19 11:31:13.58: [25442]: <-- data [1024] mag 19 11:31:13.58: [25442]: <-- data [652] mag 19 11:31:13.58: [25442]: <-- data [2] mag 19 11:31:16.69: [25442]: --> [9:] mag 19 11:31:16.69: [25442]: Problem sending TCF data mag 19 11:31:16.69: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:31:16.69: [25442]: --> [2:OK] mag 19 11:31:19.30: [25442]: --> [7:CONNECT] mag 19 11:31:19.30: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:21.89: [25442]: --> [3:11 10 03] mag 19 11:31:21.89: [25442]: --> [5:ERROR] mag 19 11:31:21.89: [25442]: MODEM Command error mag 19 11:31:21.89: [25442]: FCS error mag 19 11:31:21.89: [25442]: DELAY 1500 ms mag 19 11:31:23.39: [25442]: SEND training at v.17 12000 bit/s mag 19 11:31:23.39: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:31:23.44: [25442]: --> [7:CONNECT] mag 19 11:31:23.44: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:31:23.44: [25442]: <-- data [23] mag 19 11:31:23.44: [25442]: <-- data [2] mag 19 11:31:25.23: [25442]: --> [7:CONNECT] mag 19 11:31:25.23: [25442]: <-- HDLC<6:FF C8 C1 00 54 1E> mag 19 11:31:25.23: [25442]: <-- data [6] mag 19 11:31:25.23: [25442]: <-- data [2] mag 19 11:31:25.66: [25442]: --> [2:OK] mag 19 11:31:25.66: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:31:25.75: [25442]: --> [2:OK] mag 19 11:31:25.75: [25442]: <-- [11:AT+FTM=121\r] mag 19 11:31:25.79: [25442]: --> [7:CONNECT] mag 19 11:31:25.79: [25442]: <-- data [1024] mag 19 11:31:25.79: [25442]: <-- data [1024] mag 19 11:31:25.79: [25442]: <-- data [202] mag 19 11:31:25.79: [25442]: <-- data [2] mag 19 11:31:28.90: [25442]: --> [9:] mag 19 11:31:28.90: [25442]: Problem sending TCF data mag 19 11:31:28.90: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:31:28.90: [25442]: --> [2:OK] mag 19 11:31:31.54: [25442]: --> [7:CONNECT] mag 19 11:31:31.54: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:34.09: [25442]: --> [3:11 10 03] mag 19 11:31:34.09: [25442]: --> [5:ERROR] mag 19 11:31:34.09: [25442]: MODEM Command error mag 19 11:31:34.09: [25442]: FCS error mag 19 11:31:34.09: [25442]: DELAY 1500 ms mag 19 11:31:35.59: [25442]: SEND training at v.17 9600 bit/s mag 19 11:31:35.59: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:31:35.64: [25442]: --> [7:CONNECT] mag 19 11:31:35.64: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:31:35.64: [25442]: <-- data [23] mag 19 11:31:35.64: [25442]: <-- data [2] mag 19 11:31:37.42: [25442]: --> [7:CONNECT] mag 19 11:31:37.42: [25442]: <-- HDLC<6:FF C8 C1 00 64 1E> mag 19 11:31:37.43: [25442]: <-- data [6] mag 19 11:31:37.43: [25442]: <-- data [2] mag 19 11:31:37.85: [25442]: --> [2:OK] mag 19 11:31:37.85: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:31:37.94: [25442]: --> [2:OK] mag 19 11:31:37.94: [25442]: <-- [10:AT+FTM=97\r] mag 19 11:31:37.98: [25442]: --> [7:CONNECT] mag 19 11:31:37.98: [25442]: <-- data [1024] mag 19 11:31:37.98: [25442]: <-- data [776] mag 19 11:31:37.98: [25442]: <-- data [2] mag 19 11:31:41.09: [25442]: --> [13:] mag 19 11:31:41.09: [25442]: Problem sending TCF data mag 19 11:31:41.09: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:31:41.09: [25442]: --> [2:OK] mag 19 11:31:43.74: [25442]: --> [7:CONNECT] mag 19 11:31:43.74: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:46.28: [25442]: --> [3:11 10 03] mag 19 11:31:46.29: [25442]: --> [5:ERROR] mag 19 11:31:46.29: [25442]: MODEM Command error mag 19 11:31:46.29: [25442]: FCS error mag 19 11:31:46.29: [25442]: DELAY 1500 ms mag 19 11:31:47.79: [25442]: SEND training at v.17 7200 bit/s mag 19 11:31:47.79: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:31:47.84: [25442]: --> [7:CONNECT] mag 19 11:31:47.84: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:31:47.84: [25442]: <-- data [23] mag 19 11:31:47.84: [25442]: <-- data [2] mag 19 11:31:49.63: [25442]: --> [7:CONNECT] mag 19 11:31:49.63: [25442]: <-- HDLC<6:FF C8 C1 00 74 1E> mag 19 11:31:49.63: [25442]: <-- data [6] mag 19 11:31:49.63: [25442]: <-- data [2] mag 19 11:31:50.06: [25442]: --> [2:OK] mag 19 11:31:50.06: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:31:50.15: [25442]: --> [2:OK] mag 19 11:31:50.15: [25442]: <-- [10:AT+FTM=73\r] mag 19 11:31:50.20: [25442]: --> [7:CONNECT] mag 19 11:31:50.20: [25442]: <-- data [1024] mag 19 11:31:50.20: [25442]: <-- data [326] mag 19 11:31:50.20: [25442]: <-- data [2] mag 19 11:31:53.32: [25442]: --> [110:] mag 19 11:31:53.32: [25442]: Problem sending TCF data mag 19 11:31:53.32: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:31:53.32: [25442]: --> [2:OK] mag 19 11:31:55.92: [25442]: --> [7:CONNECT] mag 19 11:31:55.92: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:31:58.49: [25442]: --> [2:10 03] mag 19 11:31:58.50: [25442]: --> [5:ERROR] mag 19 11:31:58.50: [25442]: MODEM Command error mag 19 11:31:58.50: [25442]: FCS error mag 19 11:31:58.50: [25442]: DELAY 1500 ms mag 19 11:32:00.00: [25442]: SEND training at v.27ter 4800 bit/s mag 19 11:32:00.00: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:32:00.05: [25442]: --> [7:CONNECT] mag 19 11:32:00.05: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:32:00.05: [25442]: <-- data [23] mag 19 11:32:00.05: [25442]: <-- data [2] mag 19 11:32:01.84: [25442]: --> [7:CONNECT] mag 19 11:32:01.84: [25442]: <-- HDLC<6:FF C8 C1 00 50 1E> mag 19 11:32:01.84: [25442]: <-- data [6] mag 19 11:32:01.84: [25442]: <-- data [2] mag 19 11:32:02.28: [25442]: --> [2:OK] mag 19 11:32:02.28: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:32:02.37: [25442]: --> [2:OK] mag 19 11:32:02.37: [25442]: <-- [10:AT+FTM=48\r] mag 19 11:32:02.41: [25442]: --> [7:CONNECT] mag 19 11:32:02.41: [25442]: <-- data [900] mag 19 11:32:02.41: [25442]: <-- data [2] mag 19 11:32:04.84: [25442]: --> [2:OK] mag 19 11:32:04.84: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:32:07.45: [25442]: --> [7:CONNECT] mag 19 11:32:07.45: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:32:10.03: [25442]: --> [2:10 03] mag 19 11:32:10.03: [25442]: --> [5:ERROR] mag 19 11:32:10.03: [25442]: MODEM Command error mag 19 11:32:10.03: [25442]: FCS error mag 19 11:32:10.03: [25442]: DELAY 1500 ms mag 19 11:32:11.53: [25442]: SEND training at v.27ter fallback mode 2400 bit/s mag 19 11:32:11.53: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:32:11.58: [25442]: --> [7:CONNECT] mag 19 11:32:11.58: [25442]: <-- HDLC<23:FF C0 C2 8C 8C 8C 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04> mag 19 11:32:11.58: [25442]: <-- data [23] mag 19 11:32:11.58: [25442]: <-- data [2] mag 19 11:32:13.37: [25442]: --> [7:CONNECT] mag 19 11:32:13.37: [25442]: <-- HDLC<6:FF C8 C1 00 40 1E> mag 19 11:32:13.37: [25442]: <-- data [6] mag 19 11:32:13.37: [25442]: <-- data [2] mag 19 11:32:13.80: [25442]: --> [2:OK] mag 19 11:32:13.80: [25442]: <-- [9:AT+FTS=7\r] mag 19 11:32:13.90: [25442]: --> [2:OK] mag 19 11:32:13.90: [25442]: <-- [10:AT+FTM=24\r] mag 19 11:32:13.95: [25442]: --> [7:CONNECT] mag 19 11:32:13.95: [25442]: <-- data [450] mag 19 11:32:13.95: [25442]: <-- data [2] mag 19 11:32:16.62: [25442]: --> [2:OK] mag 19 11:32:16.62: [25442]: <-- [9:AT+FRH=3\r] mag 19 11:32:19.28: [25442]: --> [7:CONNECT] mag 19 11:32:19.28: [25442]: Andrea: Partito Timeout settato a 10 sec mag 19 11:32:21.83: [25442]: --> [2:10 03] mag 19 11:32:21.83: [25442]: --> [5:ERROR] mag 19 11:32:21.83: [25442]: MODEM Command error mag 19 11:32:21.83: [25442]: FCS error mag 19 11:32:21.83: [25442]: DELAY 1500 ms mag 19 11:32:23.33: [25442]: TRAINING failed mag 19 11:32:23.33: [25442]: <-- [9:AT+FTH=3\r] mag 19 11:32:23.38: [25442]: --> [7:CONNECT] mag 19 11:32:23.38: [25442]: <-- HDLC<3:FF C8 DF> mag 19 11:32:23.38: [25442]: <-- data [3] mag 19 11:32:23.38: [25442]: <-- data [2] mag 19 11:32:24.70: [25442]: --> [2:OK] mag 19 11:32:24.70: [25442]: MODEM input buffering enabled mag 19 11:32:24.70: [25442]: <-- [5:ATH0\r] mag 19 11:32:26.25: [25442]: --> [2:OK] mag 19 11:32:26.25: [25442]: MODEM set DTR OFF mag 19 11:32:26.25: [25442]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5) mag 19 11:32:26.25: [25442]: SESSION END ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*
- Follow-Ups:
- Re: [hylafax-users] Problem in sending TCF
- From: Lee Howard
- Re: [hylafax-users] Problem in sending TCF
- Prev by Date: [hylafax-users] Solution to files corrupted by libtiff 3.6.0 on SuSE 9.1
- Next by Date: Re: [hylafax-users] Attached TIFF mail delivery
- Previous by thread: [hylafax-users] Solution to files corrupted by libtiff 3.6.0 on SuSE 9.1
- Next by thread: Re: [hylafax-users] Problem in sending TCF
- Index(es):
Project hosted by iFAX Solutions