[hylafax-users] Problem send fax (hylafax, mandrake 9.2, whfc)

["zaidie bad" <badzenden@xxxxxxxxxxx>]

m using linux mandrake 9.2 and i have installed this package in my machine

hylafax-4.1.6-3.1.92mdk
hylafax-server-4.1.6-3.1.92mdk
hylafax-client-4.1.6-3mdk
ghostscript-7.07-14mdk
libtiff3-3.5.7-6mdk


the server is running OK.

HylaFAX scheduler on orange.linuxhouse: Running
Modem ttyS0 (60 3 40455307): Running and idle

My problem is i am using WHFC in windows client to sent fax but no page was 
sent.  The status showed it was done and dialled to destination but no page 
was sent in the transmission

faxstat -d
HylaFAX scheduler on orange.linuxhouse: Running
Modem ttyS0 (60 3 40455307): Waiting for modem to come ready
JID    Pri   S  Owner Number       Pages Dials     TTS Status
114  127 D razida 045752931     0:0   1:12

May 05 17:43:58.32: [ 5338]: SESSION BEGIN 00000096 603045752931
May 05 17:43:58.32: [ 5338]: HylaFAX (tm) Version 4.1.6
May 05 17:43:58.32: [ 5338]: SEND FAX: JOB 114 DEST 045752931 COMMID 
00000096 DEVICE '/dev/ttyS0'
May 05 17:43:58.32: [ 5338]: DELAY 75 ms
May 05 17:43:58.39: [ 5338]: DELAY 2600 ms
May 05 17:44:02.00: [ 5338]: DELAY 10 ms
May 05 17:44:02.01: [ 5338]: <-- [4:ATZ\r]
May 05 17:44:02.16: [ 5338]: --> [2:OK]
May 05 17:44:02.16: [ 5338]: DELAY 3000 ms
May 05 17:44:05.15: [ 5338]: <-- [5:ATE0\r]
May 05 17:44:05.29: [ 5338]: --> [4:ATE0]
May 05 17:44:05.29: [ 5338]: --> [2:OK]
May 05 17:44:05.29: [ 5338]: <-- [5:ATV1\r]
May 05 17:44:05.43: [ 5338]: --> [2:OK]
May 05 17:44:05.43: [ 5338]: <-- [7:ATQ0X4\r]
May 05 17:44:05.57: [ 5338]: --> [2:OK]
May 05 17:44:05.57: [ 5338]: <-- [7:ATS0=0\r]
May 05 17:44:05.71: [ 5338]: --> [2:OK]
May 05 17:44:05.71: [ 5338]: <-- [7:ATS8=2\r]
May 05 17:44:05.85: [ 5338]: --> [2:OK]
May 05 17:44:05.85: [ 5338]: <-- [8:ATS7=60\r]
May 05 17:44:05.99: [ 5338]: --> [2:OK]
May 05 17:44:05.99: [ 5338]: <-- [12:AT&H2&I2&R1\r]
May 05 17:44:06.13: [ 5338]: --> [2:OK]
May 05 17:44:06.13: [ 5338]: <-- [11:ATS13=1&D2\r]
May 05 17:44:06.27: [ 5338]: --> [2:OK]
May 05 17:44:06.27: [ 5338]: <-- [6:AT&C1\r]
May 05 17:44:06.41: [ 5338]: --> [2:OK]
May 05 17:44:06.41: [ 5338]: <-- [12:AT+FCLASS=1\r]
May 05 17:44:06.55: [ 5338]: --> [2:OK]
May 05 17:44:06.55: [ 5338]: <-- [12:AT+FCLASS=0\r]
May 05 17:44:06.69: [ 5338]: --> [2:OK]
May 05 17:44:06.69: [ 5338]: <-- [7:ATL0M1\r]
May 05 17:44:06.83: [ 5338]: --> [2:OK]
May 05 17:44:06.84: [ 5338]: <-- [12:AT+FCLASS=1\r]
May 05 17:44:07.07: [ 5338]: --> [2:OK]
May 05 17:44:07.08: [ 5338]: DIAL 045752931
May 05 17:44:07.08: [ 5338]: <-- [14:ATDT045752931\r]
May 05 17:44:42.49: [ 5338]: --> [7:CONNECT]
May 05 17:44:44.24: [ 5338]: --> [2:OK]
May 05 17:44:44.24: [ 5338]: REMOTE NSF "00 00 0E 00 00 00 96 0F 01 07 00 10 
00 02 95 80 18 01 49 02 50 49 53 43 4F 20 53 45 52 56 49 20 20 20 20 20 03 
BA"
May 05 17:44:44.24: [ 5338]: NSF remote fax equipment: Panasonic
May 05 17:44:44.24: [ 5338]: NSF remote station ID: "PISCO SERVI     "
May 05 17:44:44.24: [ 5338]: <-- [9:AT+FRH=3\r]
May 05 17:44:44.26: [ 5338]: --> [7:CONNECT]
May 05 17:44:45.01: [ 5338]: --> [2:OK]
May 05 17:44:45.01: [ 5338]: REMOTE CSI "045752931"
May 05 17:44:45.01: [ 5338]: <-- [9:AT+FRH=3\r]
May 05 17:44:45.03: [ 5338]: --> [7:CONNECT]
May 05 17:44:45.38: [ 5338]: --> [2:OK]
May 05 17:44:45.38: [ 5338]: REMOTE best rate 9600 bit/s
May 05 17:44:45.38: [ 5338]: REMOTE max page width 1728 pixels in 215 mm
May 05 17:44:45.38: [ 5338]: REMOTE max unlimited page length
May 05 17:44:45.38: [ 5338]: REMOTE best vres 7.7 line/mm
May 05 17:44:45.38: [ 5338]: REMOTE best format 2-D MMR
May 05 17:44:45.38: [ 5338]: REMOTE supports T.30 Annex A, ECM
May 05 17:44:45.38: [ 5338]: REMOTE best 20 ms/scanline
May 05 17:44:45.38: [ 5338]: USE 9600 bit/s
May 05 17:44:45.38: [ 5338]: USE 20 ms/scanline
May 05 17:44:45.38: [ 5338]: <-- [9:AT+FTH=3\r]
May 05 17:44:45.58: [ 5338]: --> [7:CONNECT]
May 05 17:44:45.58: [ 5338]: <-- data [3]
May 05 17:44:45.58: [ 5338]: <-- data [2]
May 05 17:44:46.76: [ 5338]: --> [2:OK]
May 05 17:44:46.76: [ 5338]: <-- [5:ATH0\r]
May 05 17:44:47.00: [ 5338]: --> [2:OK]
May 05 17:44:47.00: [ 5338]: SESSION END

have any idea how i can solve this problem?

this my config.ttyS0

CountryCode:            60
AreaCode:               3
FAXNumber:              "60 3 40455307"
LongDistancePrefix:     1
InternationalPrefix:    00
DialStringRules:        etc/dialrules
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0644
LogFileMode:            0644
DeviceMode:             0644
RingsBeforeAnswer:      2
SpeakerVolume:          on
GettyArgs:              "-h %l dx_%s"
LocalIdentifier:        "NothingSetup"
LogFacility:            "local5"
ClocalAsRoot:           yes
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%P of %%T"
MaxRecvPages:           25
LockVoiceCalls:         yes
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class1          # use class 1 interface
ModemRate:              19200           # rate for DCE-DTE communication
ModemFlowControl:       xonxoff         # software flow control
#
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or 
not)
ModemNoFlowCmd:         AT&H0&I0&R1     # setup modem for no flow control
ModemHardFlowCmd:       AT&H1&I0&R2     # setup modem for hardware flow 
control
ModemSoftFlowCmd:       AT&H2&I2&R1     # setup modem for software flow 
control
ModemResultCodesCmd:    ATQ0X4          # enable result codes
#
ModemMfrQueryCmd:       !USR
ModemModelQueryCmd:     ATI3
ModemRevQueryCmd:       ATI7            # XXX returns a multi-line result
#
# When AT+FCLASS=1 is issued the modem automatically switches
# to software flow control; these parameters let the fax software
# reset flow control as needed after entering Class 1.
#
Class1NFLOCmd:          AT&H0&I0&R1     # setup modem for no flow control
Class1HFLOCmd:          AT&H1&I0&R2     # setup modem for hardware flow 
control
Class1SFLOCmd:          ""              # modem does this automatically
#
# This should resolve "DIS/DTC received 3 times" errors:
#
Class1ResponseWaitCmd:  AT+FRS=1        # wait after sending TCF for 
response
#
# The remainder of this configuration is included so that the
# modem "idles" in Class 0 while not sending or receiving facsimile.
#
ModemSetupAACmd:        AT+FCLASS=0     # leave modem idling in class 0
ModemAnswerCmd:         AT+FCLASS=1A    # answer in Class 1
#
# Disables the reporting of bad frames by the modem.  This
# overcomes a firmware problem in the x2 and V90 Sportsters.
# It is not necessary for the Courier modem.
#
Class2NRCmd:    AT+FNR=1,1,1,0

_________________________________________________________________
Are you in love? Find a date on MSN Personals http://match.msn.com.my/


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*