[hylafax-users] AT+FDT -> FHS:25 (DCS) errors

[Giulio Orsero <giulioo@xxxxxxxxx>]

HylaFAX-4.1.7, MT5634ZBA-V92 fw1.28c (latest) used in class-2.1

There is a particular remote fax machine (don't know make/model) which
always causes DCS problems, as you can see in attached log. Do you think
upgrading HylaFAX could help or this is a kind of incompatibility between
modem firmware and remote machine which is unsolvable, but for using it in
class1?

Thanks

Mar 22 14:24:27.14: [25656]: SESSION BEGIN 00065987 390123456789
Mar 22 14:24:27.14: [25656]: HylaFAX (tm) Version 4.1.7
Mar 22 14:24:27.14: [25656]: SEND FAX: JOB 16160 DEST 0123456789 COMMID 00065987 DEVICE '/dev/ttyS1'
Mar 22 14:24:27.14: [25656]: DELAY 75 ms
Mar 22 14:24:27.22: [25656]: DELAY 2600 ms
Mar 22 14:24:30.83: [25656]: DELAY 10 ms
Mar 22 14:24:30.84: [25656]: <-- [4:ATZ\r]
Mar 22 14:24:32.11: [25656]: --> [2:OK]
Mar 22 14:24:32.11: [25656]: DELAY 3000 ms
Mar 22 14:24:35.11: [25656]: <-- [5:ATX3\r]
Mar 22 14:24:35.12: [25656]: --> [4:ATX3]
Mar 22 14:24:35.12: [25656]: --> [2:OK]
Mar 22 14:24:35.12: [25656]: <-- [5:ATE0\r]
Mar 22 14:24:35.13: [25656]: --> [4:ATE0]
Mar 22 14:24:35.13: [25656]: --> [2:OK]
Mar 22 14:24:35.13: [25656]: <-- [5:ATV1\r]
Mar 22 14:24:35.14: [25656]: --> [2:OK]
Mar 22 14:24:35.14: [25656]: <-- [5:ATQ0\r]
Mar 22 14:24:35.15: [25656]: --> [2:OK]
Mar 22 14:24:35.15: [25656]: <-- [7:ATS0=0\r]
Mar 22 14:24:35.16: [25656]: --> [2:OK]
Mar 22 14:24:35.16: [25656]: <-- [7:ATS8=2\r]
Mar 22 14:24:35.17: [25656]: --> [2:OK]
Mar 22 14:24:35.17: [25656]: <-- [8:ATS7=60\r]
Mar 22 14:24:35.18: [25656]: --> [2:OK]
Mar 22 14:24:35.18: [25656]: <-- [6:AT&K4\r]
Mar 22 14:24:35.19: [25656]: --> [2:OK]
Mar 22 14:24:35.19: [25656]: <-- [21:AT+FCLASS=2.1;+FRY=4\r]
Mar 22 14:24:35.20: [25656]: --> [2:OK]
Mar 22 14:24:35.20: [25656]: <-- [9:AT+FLO=1\r]
Mar 22 14:24:35.21: [25656]: --> [2:OK]
Mar 22 14:24:35.21: [25656]: <-- [9:AT+FPP=0\r]
Mar 22 14:24:35.22: [25656]: --> [2:OK]
Mar 22 14:24:35.22: [25656]: <-- [9:AT+FBO=0\r]
Mar 22 14:24:35.23: [25656]: --> [2:OK]
Mar 22 14:24:35.23: [25656]: <-- [10:AT+FCT=30\r]
Mar 22 14:24:35.24: [25656]: --> [2:OK]
Mar 22 14:24:35.24: [25656]: <-- [11:AT+FCQ=1,0\r]
Mar 22 14:24:35.25: [25656]: --> [2:OK]
Mar 22 14:24:35.25: [25656]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 22 14:24:35.26: [25656]: --> [2:OK]
Mar 22 14:24:35.26: [25656]: <-- [13:AT+FAP=1,1,1\r]
Mar 22 14:24:35.27: [25656]: --> [2:OK]
Mar 22 14:24:35.27: [25656]: <-- [9:AT+FIE=0\r]
Mar 22 14:24:35.28: [25656]: --> [2:OK]
Mar 22 14:24:35.28: [25656]: <-- [23:AT+FCC=1,D,2,2,3,1,0,0\r]
Mar 22 14:24:35.29: [25656]: --> [2:OK]
Mar 22 14:24:35.29: [25656]: <-- [5:ATM0\r]
Mar 22 14:24:35.30: [25656]: --> [2:OK]
Mar 22 14:24:35.30: [25656]: sched policy=1, priority=1
Mar 22 14:24:35.30: [25656]: <-- [21:AT+FCLASS=2.1;+FRY=4\r]
Mar 22 14:24:35.41: [25656]: --> [2:OK]
Mar 22 14:24:35.41: [25656]: <-- [9:AT+FLO=1\r]
Mar 22 14:24:35.52: [25656]: --> [2:OK]
Mar 22 14:24:35.52: [25656]: <-- [9:AT+FPP=0\r]
Mar 22 14:24:35.63: [25656]: --> [2:OK]
Mar 22 14:24:35.63: [25656]: <-- [9:AT+FBO=0\r]
Mar 22 14:24:35.74: [25656]: --> [2:OK]
Mar 22 14:24:35.74: [25656]: <-- [10:AT+FCT=30\r]
Mar 22 14:24:35.85: [25656]: --> [2:OK]
Mar 22 14:24:35.85: [25656]: <-- [11:AT+FCQ=1,0\r]
Mar 22 14:24:35.96: [25656]: --> [2:OK]
Mar 22 14:24:35.96: [25656]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 22 14:24:36.07: [25656]: --> [2:OK]
Mar 22 14:24:36.07: [25656]: <-- [13:AT+FAP=1,1,1\r]
Mar 22 14:24:36.18: [25656]: --> [2:OK]
Mar 22 14:24:36.18: [25656]: <-- [9:AT+FIE=0\r]
Mar 22 14:24:36.29: [25656]: --> [2:OK]
Mar 22 14:24:36.29: [25656]: <-- [23:AT+FCC=1,D,2,2,3,1,0,0\r]
Mar 22 14:24:36.40: [25656]: --> [2:OK]
Mar 22 14:24:36.40: [25656]: <-- [25:AT+FLI="+39 999 9999999"\r]
Mar 22 14:24:36.51: [25656]: --> [2:OK]
Mar 22 14:24:36.51: [25656]: DIAL 0,0123456789
Mar 22 14:24:36.51: [25656]: <-- [33:AT+FCC=1,,,,,,,,0;DT0,0123456789\r]
Mar 22 14:24:58.17: [25656]: --> [4:+FCO]
Mar 22 14:24:58.17: [25656]: --> [27:+FCI:"          0123456789"]
Mar 22 14:24:58.17: [25656]: REMOTE CSI "0123456789"
Mar 22 14:24:58.54: [25656]: --> [22:+FIS:3,3,0,2,1,1,0,4,0]
Mar 22 14:24:58.54: [25656]: --> [2:OK]
Mar 22 14:24:58.54: [25656]: REMOTE best rate 9600 bit/s
Mar 22 14:24:58.54: [25656]: REMOTE max page width 1728 pixels in 215 mm
Mar 22 14:24:58.54: [25656]: REMOTE max unlimited page length
Mar 22 14:24:58.54: [25656]: REMOTE best vres 7.7 line/mm
Mar 22 14:24:58.54: [25656]: REMOTE best format 2-D MR
Mar 22 14:24:58.54: [25656]: REMOTE supports T.30 Annex A, ECM
Mar 22 14:24:58.54: [25656]: REMOTE best 20 ms, 10 ms/scanline
Mar 22 14:24:58.54: [25656]: USE 9600 bit/s
Mar 22 14:24:58.54: [25656]: USE 20 ms, 10 ms/scanline
Mar 22 14:24:58.54: [25656]: USE error correction mode
Mar 22 14:24:58.54: [25656]: SEND file "docq/doc16167.ps;41"
Mar 22 14:24:58.54: [25656]: USE page width 1728 pixels in 215 mm
Mar 22 14:24:58.54: [25656]: USE unlimited page length
Mar 22 14:24:58.54: [25656]: USE 7.7 line/mm
Mar 22 14:24:58.54: [25656]: USE 2-D MR
Mar 22 14:24:58.54: [25656]: <-- [23:AT+FIS=1,3,0,2,1,1,0,4\r]
Mar 22 14:24:58.65: [25656]: --> [2:OK]
Mar 22 14:24:58.65: [25656]: <-- [7:AT+FDT\r]
Mar 22 14:25:14.94: [25656]: --> [7:+FHS:25]
Mar 22 14:25:14.94: [25656]: REMOTE HANGUP: DCS sent 3 times without response (code 25)
Mar 22 14:25:14.94: [25656]: --> [2:OK]
Mar 22 14:28:14.94: [25656]: MODEM <Timeout>
Mar 22 14:28:14.94: [25656]: SEND: DCS sent 3 times without response; Giving up after 3 attempts to send same page "docq/doc16167.ps;41", dirnum 0
Mar 22 14:28:14.94: [25656]: <-- [5:ATH0\r]
Mar 22 14:28:15.07: [25656]: --> [2:OK]
Mar 22 14:28:15.07: [25656]: sched policy=0, priority=0
Mar 22 14:28:15.07: [25656]: SESSION END
-- 
giulioo@xxxxxxxxx

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxx*