[hylafax-users] Fax Receive Problem

[Brian Marr <cabernet@xxxxxxxxxxx>]

I am still stuck on Hylafax 4.1.1 and would like to get my Computer
recieving faxes again. But is has been a while since configuring Hylafax for
this so help would be appreciated. I have studied the FAQ and other docs.
Can someone cast their eye over this to see if there is anything that would
stop faxgetty from answering a call.- any call ? 

Sending faxes is working ok except for session tracing which defies my efforts. 

For Recieving Faxes/Calls I have tested the set up with Minicom. It reporting RING3 ok. 
This is what I want. 

When I phone the fax number I can see activity in the LED's on each ring, but faxgetty 
is not answering. Should there be additional Fax commands in this file ?

Brian Marr

The config.tty file
Snip!
#
CountryCode:		
AreaCode:		08
FAXNumber:		xxxxxxxx
LongDistancePrefix:	
InternationalPrefix:	
DialStringRules:	etc/dialrules
ServerTracing:		11
SessionTracing:		0xfff 	#0x4f
RecvFileMode:		0640
LogFileMode:		0640
DeviceMode:		0660
RingsBeforeAnswer:	3
RingFax:		RING3
SpeakerVolume:		off
GettyArgs:		"-r -b %l"
LocalIdentifier:	"Brian Marr"
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
#ModemRate:		38400		# rate for DCE-DTE communication
#ModemflowControl:	xonxoff		# XON/XOFF Flow Control
ModemFlowControl:	rtscts		# default
#
ModemNoFlowCmd:		AT&K0		# setup no flow control
ModemHardFlowCmd:	AT&K3		# setup hardware flow control
ModemSoftFlowCmd:	AT&K4		# setup software flow control
ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or
not)
#
ModemMfrQueryCmd:	!Rockwell
ModemModelQueryCmd:	!RC288DPi
ModemRevQueryCmd:	ATI3		# product information
#
ModemDialCmd:		ATDT%s		# T for tone dialing
ModemSetupAACmd: 	AT+FAA=1	# Adaptive Answer placed by BM
(Snip)
====================================================================
====================================================================


Here is the class1 file 

# Generic Class 1 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
# BEGIN-SERVER
#CountryCode:		1		# USA
#LongDistancePrefix:	1
#InternationalPrefix:	011
#AreaCode:		415
#DialStringRules:	etc/dialrules
#FAXNumber:		+1.999.555.1212
#LocalIdentifier:	"NothingSetup"	# default is canonical FAXNumber
#ServerTracing:		1		# log server-related operations
#SessionTracing:		11		# log server-related
operations
#RecvFileMode:		0600		# recvd facsimile are not public
#LogFileMode:		0600		# private log files
#DeviceMode:		0600		# device is accessible only to
uucp/fax
#QualifyTSI:		etc/tsi		# accept facsimile from anyone
#SpeakerVolume:		off		# machine's are already too loud
#RingsBeforeAnswer:	1		# answer on first ring
#TagLineFont:		etc/lutRS18.pcf	# tag line font
#TagLineFormat:		"From %%l|%c|Page %%P of %%T"
#MaxBadCalls:		5		# max 5 consecutive bad calls
#PostScriptTimeout:	300		# 5 minute timeout on PostScript
jobs
#MaxSendPages:		25		# max pages in an outbound job
#MaxRecvPages:		25		# max pages in an inbound job
#ContCoverPage:		etc/cover.templ	# enable continuation cover pages
#DestControls:		etc/destcontrols # destination-specific controls
#MaxConcurrentJobs:	1		# serialize jobs to the same dest
#TimeOfDay:		"Any"		# outbound jobs any day, any time
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class1		# use this to supply a hint
#ModemRate:		19200		# rate for DCE-DTE communication
#ModemFlowControl:	xonxoff		# XON/XOFF flow control assumed
#
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD follows carrier
GettyArgs:		"-h %l dx_%s"	# modem must auto-detect fax/data
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is
reset
ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose command
results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook
(hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemSoftResetCmdDelay:	3000	# pause after soft reset
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is 2
seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem expects for
transmit
#
Class1Cmd:		AT+FCLASS=1	# command to enter class 1
Class1PPMWaitCmd:	AT+FTS=7	# command to stop and wait before
PPM
Class1TCFWaitCmd:	AT+FTS=7	# command to stop and wait before
TCF
Class1EOPWaitCmd:	AT+FTS=9	# command to stop and wait before
EOP
Class1TCFResponseDelay:	75		# 75ms delay between recv TCF &
response
Class1SendMsgDelay:	75		# 75ms delay after training
Class1SwitchingDelay:	75		# 150ms delay in switching
transmission direction
Class1TrainingRecovery:	1500		# 1.5sec delay after training
failure
Class1RecvAbortOK:	200		# wait 200ms for abort response
Class1FrameOverhead:	4		# 4 byte overhead in recvd HDLC
frames
Class1RecvIdentTimer:	40000		# 35+5secs waiting for ident frames
Class1TCFMaxNonZero:	10		# max 10% of data may be non-zero
Class1TCFMinRun:	1000		# min run is 2/3rds of TCF duration


-- 
Powered by Suse Linux 8.0

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*