Re: [hylafax-users] pager problem

[marthter <marthter@xxxxxxxx>]

Anyone have any flashes of inspiration on this pager problem in the past 
week?

I'm still stumped and needing a solution, so any informed thoughts or 
suggestions would be appreciated.

Cheers.

Martin


marthter wrote:

> Hi,
>
> I'm having problems using the sendpage command.
>
> I've got HylaFAX 4.1.7 (installed from RPM) on Redhat 9.
>
> When I send the page, the response is always (in the e-mail):
>
> Your pager job to 2325553 failed because:
> Message block transmit failed; paging central rejected it
>
> See detailed trace below.
>
> It seems fine until it gets to the point of telling the paging central
> the pager ID number to send to, then it says:
>
> Cannot deliver ID's: 0000000002325553
>
> The funny part is, this works fine if I use minicom and send the page
> using the manual mode of the TAP/IXO protocol (see minicom transcript
> below). I can tell the paging central the pager ID number as 2325553
> (same as attempted in the automatic protocol), or I can tell it as
> 0000000002325553 (the ID it complains with when my side enters the short
> version).
>
> Both PINs work in manual mode, and (if I fudge pagermap to add or not
> add the zeros) both PINs fail in automatic mode.
>
>
> This is for the Rogers (formerly Cantel, formerly AT&T) paging central
> number in Toronto, Ontario, Canada, in case anyone else has had success
> in this neighbourhood.
>
> If anyone can help diagnose this, it will be GREATLY appreciated.
>
> Regards.
>
> Martin
>
>
>
>
>
> Oct 05 01:13:46.39: [ 9213]: SESSION BEGIN 00000566 14164889494
> Oct 05 01:13:46.39: [ 9213]: HylaFAX (tm) Version 4.1.7
> Oct 05 01:13:46.39: [ 9213]: SEND PAGE: JOB 460 DEST 416-488-9494 
> COMMID 00000566
> Oct 05 01:13:46.39: [ 9213]: MODEM set DTR OFF
> Oct 05 01:13:46.39: [ 9213]: DELAY 75 ms
> Oct 05 01:13:46.46: [ 9213]: MODEM set DTR ON
> Oct 05 01:13:46.46: [ 9213]: DELAY 2600 ms
> Oct 05 01:13:50.07: [ 9213]: MODEM set baud rate: 9600 baud, input 
> flow XON/XOFF, output flow XON/XOFF
> Oct 05 01:13:50.07: [ 9213]: DELAY 10 ms
> Oct 05 01:13:50.08: [ 9213]: MODEM flush i/o
> Oct 05 01:13:50.08: [ 9213]: <-- [4:ATZ\r]
> Oct 05 01:13:50.10: [ 9213]: --> [2:OK]
> Oct 05 01:13:50.10: [ 9213]: DELAY 3000 ms
> Oct 05 01:13:53.10: [ 9213]: <-- [5:ATE0\r]
> Oct 05 01:13:53.11: [ 9213]: --> [4:ATE0]
> Oct 05 01:13:53.12: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.12: [ 9213]: <-- [5:ATV1\r]
> Oct 05 01:13:53.14: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.14: [ 9213]: <-- [7:ATQ0X4\r]
> Oct 05 01:13:53.16: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.16: [ 9213]: <-- [7:ATS0=0\r]
> Oct 05 01:13:53.18: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.18: [ 9213]: <-- [7:ATS8=2\r]
> Oct 05 01:13:53.20: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.20: [ 9213]: <-- [8:ATS7=60\r]
> Oct 05 01:13:53.22: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.22: [ 9213]: <-- [12:AT&H2&I2&R1\r]
> Oct 05 01:13:53.24: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.24: [ 9213]: <-- [11:ATS13=1&D2\r]
> Oct 05 01:13:53.26: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.26: [ 9213]: <-- [6:AT&C1\r]
> Oct 05 01:13:53.28: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.28: [ 9213]: <-- [7:ATL3M1\r]
> Oct 05 01:13:53.30: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.30: [ 9213]: MODEM set parity: 7 bits, even parity
> Oct 05 01:13:53.30: [ 9213]: STATE CHANGE: RUNNING -> SENDING
> Oct 05 01:13:53.30: [ 9213]: MODEM input buffering enabled
> Oct 05 01:13:53.30: [ 9213]: <-- [12:AT+FCLASS=0\r]
> Oct 05 01:13:53.43: [ 9213]: --> [2:OK]
> Oct 05 01:13:53.43: [ 9213]: DIAL 4164889494
> Oct 05 01:13:53.43: [ 9213]: <-- [17:ATX3DT4164889494\r]
> Oct 05 01:14:06.38: [ 9213]: --> [17:CONNECT 2400/NONE]
> Oct 05 01:14:06.38: [ 9213]: EXPECT ID (paging central identification)
> Oct 05 01:14:06.38: [ 9213]: <-- <1:\015>
> Oct 05 01:14:06.86: [ 9213]: --> <4:\000ID=>
> Oct 05 01:14:06.86: [ 9213]: RECVunknown paging central response:
> Oct 05 01:14:06.86: [ 9213]: <-- <1:\015>
> Oct 05 01:14:07.18: [ 9213]: --> <3:ID=>
> Oct 05 01:14:07.18: [ 9213]: RECV ID ("ID=")
> Oct 05 01:14:07.18: [ 9213]: SEND device identification/login request
> Oct 05 01:14:07.18: [ 9213]: <-- <5:\033PG1\015>
> Oct 05 01:14:08.25: [ 9213]: --> <1:\006>
> Oct 05 01:14:08.25: [ 9213]: RECV ACK (login successful)
> Oct 05 01:14:08.75: [ 9213]: --> <3:\033[p>
> Oct 05 01:14:08.75: [ 9213]: RECV go-ahead (prologue done)
> Oct 05 01:14:08.75: [ 9213]: SEND message block
> Oct 05 01:14:08.75: [ 9213]: <-- <15:\0022325553\015\015\003188\015>
> Oct 05 01:14:09.38: [ 9213]: --> <38: >
> Oct 05 01:14:09.38: [ 9213]: RECV: Cannot deliver ID's: 0000000002325553
> Oct 05 01:14:09.38: [ 9213]: --> <1:\036>
> Oct 05 01:14:09.38: [ 9213]: RECV RS (message block rejected; skip to 
> next)
> Oct 05 01:14:09.38: [ 9213]: <-- [5:ATH0\r]
> Oct 05 01:14:09.83: [ 9213]: --> [19:Too Slow - Good Bye]
> Oct 05 01:14:11.65: [ 9213]: --> 
> [84:qRFZ+WywTA6;J4K=l$A*A<o#wq~tvn#d?/@8pLODoh  1 
> N     -J*04EMlz)QF=? bB]
> Oct 05 01:14:11.65: [ 9213]: --> [10:NO CARRIER]
> Oct 05 01:14:11.65: [ 9213]: MODEM No carrier
> Oct 05 01:14:11.65: [ 9213]: STATE CHANGE: SENDING -> MODEMWAIT
> Oct 05 01:14:11.65: [ 9213]: MODEM input buffering enabled
> Oct 05 01:14:11.65: [ 9213]: MODEM set DTR OFF
> Oct 05 01:14:11.65: [ 9213]: SESSION END
>
>
>
>
>
> Here is the manual mode IXO/TAP as done with minicom (2400, 7e1):
>
> OK
> atdt4164889494
> CONNECT 2400/NONE
> ID=                  <--I press enter to get the ID= prompt
>                     <--I press M enter to start manual mode
> Enter pager ID(s):
> 2325553              <--I type pager number
> Enter Numeric Message:
> 1234567890123456789  <--I type the message
> More Pages?
>   Good Bye          <--I press N enter
> 1kA. D.9p("+z@`.[^; y|k.7.-.
> NO CARRIER
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List 
> _______________________
>  To subscribe/unsubscribe, click 
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < 
> /dev/null
>  *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*


____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*