[hylafax-users] pager problem

[Martin Muc <Martin.Muc@xxxxxxxxxxx>]

Hi,

I'm having problems using the sendpage command.

I've got HylaFAX 4.1.7 (installed from RPM) on Redhat 9.

When I send the page, the response is always (in the e-mail):

Your pager job to 2325553 failed because:
Message block transmit failed; paging central rejected it

See detailed trace below.

It seems fine until it gets to the point of telling the paging central 
the pager ID number to send to, then it says:

Cannot deliver ID's: 0000000002325553

The funny part is, this works fine if I use minicom and send the page 
using the manual mode of the TAP/IXO protocol (see minicom transcript 
below). I can tell the paging central the pager ID number as 2325553 
(same as attempted in the automatic protocol), or I can tell it as 
0000000002325553 (the ID it complains with when my side enters the short 
version).

Both PINs work in manual mode, and (if I fudge pagermap to add or not 
add the zeros) both PINs fail in automatic mode.


This is for the Rogers (formerly Cantel, formerly AT&T) paging central 
number in Toronto, Ontario, Canada, in case anyone else has had success 
in this neighbourhood.

If anyone can help diagnose this, it will be GREATLY appreciated.

Regards.

Martin





Oct 05 01:13:46.39: [ 9213]: SESSION BEGIN 00000566 14164889494
Oct 05 01:13:46.39: [ 9213]: HylaFAX (tm) Version 4.1.7
Oct 05 01:13:46.39: [ 9213]: SEND PAGE: JOB 460 DEST 416-488-9494 COMMID 00000566
Oct 05 01:13:46.39: [ 9213]: MODEM set DTR OFF
Oct 05 01:13:46.39: [ 9213]: DELAY 75 ms
Oct 05 01:13:46.46: [ 9213]: MODEM set DTR ON
Oct 05 01:13:46.46: [ 9213]: DELAY 2600 ms
Oct 05 01:13:50.07: [ 9213]: MODEM set baud rate: 9600 baud, input flow XON/XOFF, output flow XON/XOFF
Oct 05 01:13:50.07: [ 9213]: DELAY 10 ms
Oct 05 01:13:50.08: [ 9213]: MODEM flush i/o
Oct 05 01:13:50.08: [ 9213]: <-- [4:ATZ\r]
Oct 05 01:13:50.10: [ 9213]: --> [2:OK]
Oct 05 01:13:50.10: [ 9213]: DELAY 3000 ms
Oct 05 01:13:53.10: [ 9213]: <-- [5:ATE0\r]
Oct 05 01:13:53.11: [ 9213]: --> [4:ATE0]
Oct 05 01:13:53.12: [ 9213]: --> [2:OK]
Oct 05 01:13:53.12: [ 9213]: <-- [5:ATV1\r]
Oct 05 01:13:53.14: [ 9213]: --> [2:OK]
Oct 05 01:13:53.14: [ 9213]: <-- [7:ATQ0X4\r]
Oct 05 01:13:53.16: [ 9213]: --> [2:OK]
Oct 05 01:13:53.16: [ 9213]: <-- [7:ATS0=0\r]
Oct 05 01:13:53.18: [ 9213]: --> [2:OK]
Oct 05 01:13:53.18: [ 9213]: <-- [7:ATS8=2\r]
Oct 05 01:13:53.20: [ 9213]: --> [2:OK]
Oct 05 01:13:53.20: [ 9213]: <-- [8:ATS7=60\r]
Oct 05 01:13:53.22: [ 9213]: --> [2:OK]
Oct 05 01:13:53.22: [ 9213]: <-- [12:AT&H2&I2&R1\r]
Oct 05 01:13:53.24: [ 9213]: --> [2:OK]
Oct 05 01:13:53.24: [ 9213]: <-- [11:ATS13=1&D2\r]
Oct 05 01:13:53.26: [ 9213]: --> [2:OK]
Oct 05 01:13:53.26: [ 9213]: <-- [6:AT&C1\r]
Oct 05 01:13:53.28: [ 9213]: --> [2:OK]
Oct 05 01:13:53.28: [ 9213]: <-- [7:ATL3M1\r]
Oct 05 01:13:53.30: [ 9213]: --> [2:OK]
Oct 05 01:13:53.30: [ 9213]: MODEM set parity: 7 bits, even parity
Oct 05 01:13:53.30: [ 9213]: STATE CHANGE: RUNNING -> SENDING
Oct 05 01:13:53.30: [ 9213]: MODEM input buffering enabled
Oct 05 01:13:53.30: [ 9213]: <-- [12:AT+FCLASS=0\r]
Oct 05 01:13:53.43: [ 9213]: --> [2:OK]
Oct 05 01:13:53.43: [ 9213]: DIAL 4164889494
Oct 05 01:13:53.43: [ 9213]: <-- [17:ATX3DT4164889494\r]
Oct 05 01:14:06.38: [ 9213]: --> [17:CONNECT 2400/NONE]
Oct 05 01:14:06.38: [ 9213]: EXPECT ID (paging central identification)
Oct 05 01:14:06.38: [ 9213]: <-- <1:\015>
Oct 05 01:14:06.86: [ 9213]: --> <4:\000ID=>
Oct 05 01:14:06.86: [ 9213]: RECVunknown paging central response:
Oct 05 01:14:06.86: [ 9213]: <-- <1:\015>
Oct 05 01:14:07.18: [ 9213]: --> <3:ID=>
Oct 05 01:14:07.18: [ 9213]: RECV ID ("ID=")
Oct 05 01:14:07.18: [ 9213]: SEND device identification/login request
Oct 05 01:14:07.18: [ 9213]: <-- <5:\033PG1\015>
Oct 05 01:14:08.25: [ 9213]: --> <1:\006>
Oct 05 01:14:08.25: [ 9213]: RECV ACK (login successful)
Oct 05 01:14:08.75: [ 9213]: --> <3:\033[p>
Oct 05 01:14:08.75: [ 9213]: RECV go-ahead (prologue done)
Oct 05 01:14:08.75: [ 9213]: SEND message block
Oct 05 01:14:08.75: [ 9213]: <-- <15:\0022325553\015\015\003188\015>
Oct 05 01:14:09.38: [ 9213]: --> <38: >
Oct 05 01:14:09.38: [ 9213]: RECV: Cannot deliver ID's: 0000000002325553
Oct 05 01:14:09.38: [ 9213]: --> <1:\036>
Oct 05 01:14:09.38: [ 9213]: RECV RS (message block rejected; skip to next)
Oct 05 01:14:09.38: [ 9213]: <-- [5:ATH0\r]
Oct 05 01:14:09.83: [ 9213]: --> [19:Too Slow - Good Bye]
Oct 05 01:14:11.65: [ 9213]: --> [84:qRFZ+WywTA6;J4K=l$A*A<o#wq~tvn#d/@8pLODoh      1 N     -J*04EMlz)QF=? bB]
Oct 05 01:14:11.65: [ 9213]: --> [10:NO CARRIER]
Oct 05 01:14:11.65: [ 9213]: MODEM No carrier
Oct 05 01:14:11.65: [ 9213]: STATE CHANGE: SENDING -> MODEMWAIT
Oct 05 01:14:11.65: [ 9213]: MODEM input buffering enabled
Oct 05 01:14:11.65: [ 9213]: MODEM set DTR OFF
Oct 05 01:14:11.65: [ 9213]: SESSION END





Here is the manual mode IXO/TAP as done with minicom (2400, 7e1):

OK
atdt4164889494
CONNECT 2400/NONE
ID=                  <--I press enter to get the ID= prompt
                    <--I press M enter to start manual mode
Enter pager ID(s):
2325553              <--I type pager number
Enter Numeric Message:
1234567890123456789  <--I type the message
More Pages?
  Good Bye          <--I press N enter
1kA. D.9p("+z@`.[^; y|k.7.-.
NO CARRIER



____________________ HylaFAX(tm) Users Mailing List _______________________
 To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@xxxxxxxxxxx < /dev/null
 *To learn about commercial HylaFAX(tm) support, mail sales@xxxxxxxxxxxx*