HylaFAX The world's most advanced open source fax server

[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: [hylafax-users] Some users don't get all scan lines



On 2003.08.30 16:59 Michael Evans wrote:

> I started with newly extracted sources from the 4.1.7 tarball.

Unfortunately, you may need to use CVS and not 4.1.7... I can't say for 
certain.

> I first applied the patch to support Class1TMConnectDelay (428); then 
> I applied the patch for Class1ValidateV21Frames (442); and finally, 
> the last patch on the bugzilla page for ECM support (461). When this 
> last was applied, the patch command said there were 3 HUNKs that 
> failed.

Due to the fact that the patch applies against CVS and not 4.1.7.

> One was in a modem config file I'm not using, but 2 were in 
> /faxd/Class1Recv.c++, so I fixed this file manually. (Were other 
> patches on the bugzilla page for bug 232 supposed to be applied as 
> well?)

No, you only use the last patch.

> Obviously I'm going to delete this build and go back to 4.1.7, but at 
> this point I'm thinking seriously about some hardware other than the 
> currently installed Zoom 2920.

I've used a Zoom 2920 with no problems, as well as Zoom's USB version 
of that modem line, also without problems.

> Aug 30 15:17:28.30: [28881]: SEND training at v.17 14400 bit/s
> Aug 30 15:17:28.30: [28881]: <-- [9:AT+FTH=3\r]
> Aug 30 15:17:29.16: [28881]: --> [7:CONNECT]
> Aug 30 15:17:29.16: [28881]: <-- data [23]
> Aug 30 15:17:29.16: [28881]: <-- data [2]
> Aug 30 15:17:29.17: [28881]: --> [7:CONNECT]
> Aug 30 15:17:29.17: [28881]: <-- data [6]
> Aug 30 15:17:29.17: [28881]: <-- data [2]
> Aug 30 15:17:30.26: [28881]: --> [2:OK]
> Aug 30 15:17:30.26: [28881]: <-- [9:AT+FTS=7\r]
> Aug 30 15:17:30.32: [28881]: --> [2:OK]
> Aug 30 15:17:30.32: [28881]: <-- [11:AT+FTM=145\r]
> Aug 30 15:17:30.33: [28881]: --> [7:CONNECT]
> Aug 30 15:17:30.33: [28881]: DELAY 400 ms
> Aug 30 15:17:30.73: [28881]: <-- data [1024]
> Aug 30 15:17:30.73: [28881]: <-- data [1024]
> Aug 30 15:17:30.73: [28881]: <-- data [652]
> Aug 30 15:17:30.73: [28881]: <-- data [2]
> Aug 30 15:17:33.46: [28881]: --> [2:OK]
> Aug 30 15:17:33.46: [28881]: <-- [9:AT+FRH=3\r]
> Aug 30 15:17:33.81: [28881]: --> [7:CONNECT]
> Aug 30 15:17:34.98: [28881]: --> [2:OK]
> Aug 30 15:17:34.98: [28881]: TRAINING succeeded

Notice that this time we got a successful training at 14400.  So there 
is some improvement.

As for the "no response to PPS sent 3 times" error that you're getting, 
I'd prefer to wait until after you try CVS before trying to figure out 
that problem... since something in CVS may make a difference here.  (I 
can't say *what* off-hand, though.)

Lee.

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*




Project hosted by iFAX Solutions