Re: [hylafax-users] Some users don't get all scan lines

[Michael Evans <michael@togawasmith.com>]

Lee Howard wrote:

> On 2003.08.25 17:44 Michael Evans wrote:
>
>> Is it time to yank the Zoom 2920 modem and get a Multitech, or is 
>> there something else I can try?
>
>
> Post the new session log.  The one from before was at unreliable 
> bitrates, which was why Class1TMConnectDelay was required.
>
> Lee.

Lee,

When I try to send a fax to the HP, I get 2 or 3 session logs because 
Hylafax tries 3 times and gets the RTN error, then tries again. In the 
last attempt, Hylafax didn't get the RTN error on the 4th attempt 
(second log), but the fax still did not come out correctly at the HP 
(most of it was missing). These two logs are attached. I have the 
Session Tracing set to 0x4f  in case the extra information is helpful.

Michael
Aug 26 15:21:32.63: [ 1094]: SESSION BEGIN 00000081 16267961336
Aug 26 15:21:32.63: [ 1094]: HylaFAX (tm) Version 4.1
Aug 26 15:21:32.63: [ 1094]: SEND FAX: JOB 50 DEST 7961336 COMMID 00000081
Aug 26 15:21:32.63: [ 1094]: DEVICE '/dev/ttyS4'
Aug 26 15:21:32.63: [ 1094]: MODEM set DTR OFF
Aug 26 15:21:32.63: [ 1094]: DELAY 75 ms
Aug 26 15:21:32.71: [ 1094]: MODEM set DTR ON
Aug 26 15:21:32.71: [ 1094]: DELAY 2600 ms
Aug 26 15:21:35.31: [ 1094]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output
 flow XON/XOFF
Aug 26 15:21:35.31: [ 1094]: MODEM flush i/o
Aug 26 15:21:35.31: [ 1094]: <-- [4:ATZ\r]
Aug 26 15:21:35.47: [ 1094]: --> [3:ATZ]
Aug 26 15:21:35.47: [ 1094]: --> [2:OK]
Aug 26 15:21:35.47: [ 1094]: <-- [5:ATE0\r]
Aug 26 15:21:35.48: [ 1094]: --> [4:ATE0]
Aug 26 15:21:35.48: [ 1094]: --> [2:OK]
Aug 26 15:21:35.48: [ 1094]: <-- [5:ATV1\r]
Aug 26 15:21:35.49: [ 1094]: --> [2:OK]
Aug 26 15:21:35.49: [ 1094]: <-- [5:ATQ0\r]
Aug 26 15:21:35.50: [ 1094]: --> [2:OK]
Aug 26 15:21:35.50: [ 1094]: <-- [7:ATS0=0\r]
Aug 26 15:21:35.51: [ 1094]: --> [2:OK]
Aug 26 15:21:35.51: [ 1094]: <-- [7:ATS8=2\r]
Aug 26 15:21:35.52: [ 1094]: --> [2:OK]
Aug 26 15:21:35.52: [ 1094]: <-- [8:ATS7=60\r]
Aug 26 15:21:35.53: [ 1094]: --> [2:OK]
Aug 26 15:21:35.53: [ 1094]: <-- [9:AT+FLO=1\r]
Aug 26 15:21:35.54: [ 1094]: --> [2:OK]
Aug 26 15:21:35.54: [ 1094]: <-- [6:AT&D3\r]
Aug 26 15:21:35.55: [ 1094]: --> [2:OK]
Aug 26 15:21:35.55: [ 1094]: <-- [6:AT&C1\r]
Aug 26 15:21:35.56: [ 1094]: --> [2:OK]
Aug 26 15:21:35.56: [ 1094]: <-- [12:AT+FCLASS=1\r]
Aug 26 15:21:35.57: [ 1094]: --> [2:OK]
Aug 26 15:21:35.57: [ 1094]: <-- [5:ATM0\r]
Aug 26 15:21:35.58: [ 1094]: --> [2:OK]
Aug 26 15:21:35.58: [ 1094]: MODEM input buffering enabled
Aug 26 15:21:35.58: [ 1094]: <-- [12:AT+FCLASS=1\r]
Aug 26 15:21:35.69: [ 1094]: --> [2:OK]
Aug 26 15:21:35.69: [ 1094]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 26 15:21:35.69: [ 1094]: DIAL 7961336
Aug 26 15:21:35.69: [ 1094]: <-- [12:ATDT7961336\r]
Aug 26 15:22:11.04: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:11.04: [ 1094]: MODEM input buffering disabled
Aug 26 15:22:12.42: [ 1094]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Aug 26 15:22:12.42: [ 1094]: --> [2:OK]
Aug 26 15:22:12.42: [ 1094]: REMOTE NSF "AD 00 36 A0 00 00 00 00 38"
Aug 26 15:22:12.42: [ 1094]: NSF remote fax equipment: HP
Aug 26 15:22:12.42: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:12.43: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:13.12: [ 1094]: --> HDLC<25:FF C0 02 6C CC CC 8C 04 6C 9C EC 04 6C 4C 6C 04
04 04 04 04 04 04 04 AD A7>
Aug 26 15:22:13.12: [ 1094]: --> [2:OK]
Aug 26 15:22:13.12: [ 1094]: REMOTE CSI "626 796 1336"
Aug 26 15:22:13.12: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:13.13: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:13.56: [ 1094]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 19 00 3A A4>
Aug 26 15:22:13.56: [ 1094]: --> [2:OK]
Aug 26 15:22:13.56: [ 1094]: REMOTE best rate 14400 bit/s
Aug 26 15:22:13.56: [ 1094]: REMOTE max page width 1728 pixels in 215 mm
Aug 26 15:22:13.56: [ 1094]: REMOTE max unlimited page length
Aug 26 15:22:13.56: [ 1094]: REMOTE best vres 7.7 line/mm
Aug 26 15:22:13.56: [ 1094]: REMOTE best format 2-D MMR
Aug 26 15:22:13.56: [ 1094]: REMOTE supports T.30 Annex A, ECM
Aug 26 15:22:13.56: [ 1094]: REMOTE best 0 ms/scanline
Aug 26 15:22:13.56: [ 1094]: USE 14400 bit/s
Aug 26 15:22:13.56: [ 1094]: USE 0 ms/scanline
Aug 26 15:22:13.56: [ 1094]: SEND file "docq/doc50.ps;71"
Aug 26 15:22:13.56: [ 1094]: USE page width 1728 pixels in 215 mm
Aug 26 15:22:13.56: [ 1094]: USE unlimited page length
Aug 26 15:22:13.56: [ 1094]: USE 7.7 line/mm
Aug 26 15:22:13.56: [ 1094]: USE 2-D MR
Aug 26 15:22:13.56: [ 1094]: SEND training at v.17 14400 bit/s
Aug 26 15:22:13.56: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:22:14.42: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:14.42: [ 1094]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:22:14.42: [ 1094]: <-- data [23]
Aug 26 15:22:14.42: [ 1094]: <-- data [2]
Aug 26 15:22:14.43: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:14.43: [ 1094]: <-- HDLC<6:FF C8 C1 00 47 1E>
Aug 26 15:22:14.43: [ 1094]: <-- data [6]
Aug 26 15:22:14.43: [ 1094]: <-- data [2]
Aug 26 15:22:15.52: [ 1094]: --> [2:OK]
Aug 26 15:22:15.52: [ 1094]: DELAY 75 ms
Aug 26 15:22:15.60: [ 1094]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:22:15.60: [ 1094]: <-- [11:AT+FTM=145\r]
Aug 26 15:22:15.61: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:15.61: [ 1094]: <-- data [1024]
Aug 26 15:22:15.61: [ 1094]: <-- data [1024]
Aug 26 15:22:15.61: [ 1094]: <-- data [652]
Aug 26 15:22:15.61: [ 1094]: <-- data [2]
Aug 26 15:22:18.74: [ 1094]: --> [2:OK]
Aug 26 15:22:18.74: [ 1094]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:22:18.74: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:18.86: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:20.13: [ 1094]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:22:20.13: [ 1094]: --> [2:OK]
Aug 26 15:22:20.13: [ 1094]: DELAY 1500 ms
Aug 26 15:22:21.63: [ 1094]: SEND training at v.17 12000 bit/s
Aug 26 15:22:21.63: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:22:22.49: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:22.49: [ 1094]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:22:22.49: [ 1094]: <-- data [23]
Aug 26 15:22:22.49: [ 1094]: <-- data [2]
Aug 26 15:22:22.50: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:22.50: [ 1094]: <-- HDLC<6:FF C8 C1 00 57 1E>
Aug 26 15:22:22.50: [ 1094]: <-- data [6]
Aug 26 15:22:22.50: [ 1094]: <-- data [2]
Aug 26 15:22:23.59: [ 1094]: --> [2:OK]
Aug 26 15:22:23.59: [ 1094]: DELAY 75 ms
Aug 26 15:22:23.67: [ 1094]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:22:23.67: [ 1094]: <-- [11:AT+FTM=121\r]
Aug 26 15:22:23.68: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:23.68: [ 1094]: <-- data [1024]
Aug 26 15:22:23.68: [ 1094]: <-- data [1024]
Aug 26 15:22:23.68: [ 1094]: <-- data [202]
Aug 26 15:22:23.68: [ 1094]: <-- data [2]
Aug 26 15:22:26.82: [ 1094]: --> [2:OK]
Aug 26 15:22:26.82: [ 1094]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:22:26.82: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:27.09: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:28.21: [ 1094]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:22:28.21: [ 1094]: --> [2:OK]
Aug 26 15:22:28.21: [ 1094]: DELAY 1500 ms
Aug 26 15:22:29.71: [ 1094]: SEND training at v.17 9600 bit/s
Aug 26 15:22:29.71: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:22:30.57: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:30.57: [ 1094]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:22:30.57: [ 1094]: <-- data [23]
Aug 26 15:22:30.57: [ 1094]: <-- data [2]
Aug 26 15:22:30.58: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:30.58: [ 1094]: <-- HDLC<6:FF C8 C1 00 67 1E>
Aug 26 15:22:30.58: [ 1094]: <-- data [6]
Aug 26 15:22:30.58: [ 1094]: <-- data [2]
Aug 26 15:22:31.67: [ 1094]: --> [2:OK]
Aug 26 15:22:31.67: [ 1094]: DELAY 75 ms
Aug 26 15:22:31.75: [ 1094]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:22:31.75: [ 1094]: <-- [10:AT+FTM=97\r]
Aug 26 15:22:31.76: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:31.76: [ 1094]: <-- data [1024]
Aug 26 15:22:31.76: [ 1094]: <-- data [776]
Aug 26 15:22:31.76: [ 1094]: <-- data [2]
Aug 26 15:22:34.90: [ 1094]: --> [2:OK]
Aug 26 15:22:34.90: [ 1094]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:22:34.90: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:35.02: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:36.29: [ 1094]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:22:36.29: [ 1094]: --> [2:OK]
Aug 26 15:22:36.29: [ 1094]: DELAY 1500 ms
Aug 26 15:22:37.79: [ 1094]: SEND training at v.17 7200 bit/s
Aug 26 15:22:37.79: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:22:38.65: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:38.65: [ 1094]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:22:38.65: [ 1094]: <-- data [23]
Aug 26 15:22:38.65: [ 1094]: <-- data [2]
Aug 26 15:22:38.66: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:38.66: [ 1094]: <-- HDLC<6:FF C8 C1 00 77 1E>
Aug 26 15:22:38.66: [ 1094]: <-- data [6]
Aug 26 15:22:38.66: [ 1094]: <-- data [2]
Aug 26 15:22:39.75: [ 1094]: --> [2:OK]
Aug 26 15:22:39.75: [ 1094]: DELAY 75 ms
Aug 26 15:22:39.83: [ 1094]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:22:39.83: [ 1094]: <-- [10:AT+FTM=73\r]
Aug 26 15:22:39.84: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:39.84: [ 1094]: <-- data [1024]
Aug 26 15:22:39.84: [ 1094]: <-- data [326]
Aug 26 15:22:39.84: [ 1094]: <-- data [2]
Aug 26 15:22:42.99: [ 1094]: --> [2:OK]
Aug 26 15:22:42.99: [ 1094]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:22:42.99: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:22:43.11: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:44.38: [ 1094]: --> HDLC<5:FF C8 21 57 BE>
Aug 26 15:22:44.38: [ 1094]: --> [2:OK]
Aug 26 15:22:44.38: [ 1094]: TRAINING succeeded
Aug 26 15:22:44.38: [ 1094]: DELAY 75 ms
Aug 26 15:22:44.46: [ 1094]: <-- [10:AT+FTM=74\r]
Aug 26 15:22:44.47: [ 1094]: --> [7:CONNECT]
Aug 26 15:22:44.47: [ 1094]: SEND begin page
Aug 26 15:22:44.47: [ 1094]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:22:44.47: [ 1094]: <-- data [1029]
Aug 26 15:22:44.47: [ 1094]: <-- data [1025]
Aug 26 15:22:44.47: [ 1094]: <-- data [1037]
Aug 26 15:22:44.47: [ 1094]: <-- data [1030]
Aug 26 15:22:44.47: [ 1094]: <-- data [1029]
Aug 26 15:22:44.93: [ 1094]: <-- data [1035]
Aug 26 15:22:44.93: [ 1094]: <-- data [1031]
Aug 26 15:22:45.57: [ 1094]: <-- data [1032]
Aug 26 15:22:46.69: [ 1094]: <-- data [1037]
Aug 26 15:22:47.77: [ 1094]: <-- data [1041]
Aug 26 15:22:49.05: [ 1094]: <-- data [1034]
Aug 26 15:22:50.17: [ 1094]: <-- data [1039]
Aug 26 15:22:51.27: [ 1094]: <-- data [1031]
Aug 26 15:22:52.47: [ 1094]: <-- data [1027]
Aug 26 15:22:53.59: [ 1094]: <-- data [1028]
Aug 26 15:22:54.69: [ 1094]: <-- data [1030]
Aug 26 15:22:55.79: [ 1094]: <-- data [1031]
Aug 26 15:22:56.89: [ 1094]: <-- data [270]
Aug 26 15:22:57.21: [ 1094]: SENT 17677 bytes of data
Aug 26 15:22:57.21: [ 1094]: SEND 2D RTC
Aug 26 15:22:57.21: [ 1094]: <-- data [30]
Aug 26 15:22:57.21: [ 1094]: <-- data [2]
Aug 26 15:22:57.21: [ 1094]: SEND end page
Aug 26 15:23:04.54: [ 1094]: --> [2:OK]
Aug 26 15:23:04.54: [ 1094]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:23:04.54: [ 1094]: DELAY 200 ms
Aug 26 15:23:04.74: [ 1094]: SEND send EOP (no more pages or documents)
Aug 26 15:23:04.74: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:23:05.60: [ 1094]: --> [7:CONNECT]
Aug 26 15:23:05.60: [ 1094]: <-- HDLC<3:FF C8 F4>
Aug 26 15:23:05.60: [ 1094]: <-- data [3]
Aug 26 15:23:05.60: [ 1094]: <-- data [2]
Aug 26 15:23:05.92: [ 1094]: --> [2:OK]
Aug 26 15:23:05.92: [ 1094]: <-- [9:AT+FRH=3\r]
Aug 26 15:23:06.02: [ 1094]: --> [7:CONNECT]
Aug 26 15:23:07.28: [ 1094]: --> HDLC<5:FF C8 31 45 8F>
Aug 26 15:23:07.28: [ 1094]: --> [2:OK]
Aug 26 15:23:07.28: [ 1094]: SEND recv MCF (message confirmation)
Aug 26 15:23:07.28: [ 1094]: SEND FAX (00000081): FROM michael@togawasmith.com TO 7961336
 (page 1 of 1 sent in 0:54)
Aug 26 15:23:07.28: [ 1094]: SEND FAX (00000081): FROM michael@togawasmith.com TO 7961336
 (docq/doc50.ps;71 sent in 0:54)
Aug 26 15:23:07.28: [ 1094]: <-- [9:AT+FTH=3\r]
Aug 26 15:23:08.15: [ 1094]: --> [7:CONNECT]
Aug 26 15:23:08.15: [ 1094]: <-- HDLC<3:FF C8 DF>
Aug 26 15:23:08.15: [ 1094]: <-- data [3]
Aug 26 15:23:08.15: [ 1094]: <-- data [2]
Aug 26 15:23:08.47: [ 1094]: --> [2:OK]
Aug 26 15:23:08.47: [ 1094]: MODEM input buffering enabled
Aug 26 15:23:08.47: [ 1094]: <-- [5:ATH0\r]
Aug 26 15:23:09.54: [ 1094]: --> [2:OK]
Aug 26 15:23:09.54: [ 1094]: MODEM set DTR OFF
Aug 26 15:23:09.54: [ 1094]: SESSION END
Aug 26 15:17:04.01: [ 1092]: SESSION BEGIN 00000080 16267961336
Aug 26 15:17:04.01: [ 1092]: HylaFAX (tm) Version 4.1
Aug 26 15:17:04.01: [ 1092]: SEND FAX: JOB 50 DEST 7961336 COMMID 00000080
Aug 26 15:17:04.01: [ 1092]: DEVICE '/dev/ttyS4'
Aug 26 15:17:04.01: [ 1092]: MODEM set DTR OFF
Aug 26 15:17:04.01: [ 1092]: DELAY 75 ms
Aug 26 15:17:04.09: [ 1092]: MODEM set DTR ON
Aug 26 15:17:04.09: [ 1092]: DELAY 2600 ms
Aug 26 15:17:06.69: [ 1092]: MODEM set baud rate: 19200 baud, input flow XON/XOF
F, output flow XON/XOFF
Aug 26 15:17:06.69: [ 1092]: MODEM flush i/o
Aug 26 15:17:06.69: [ 1092]: <-- [4:ATZ\r]
Aug 26 15:17:06.85: [ 1092]: --> [3:ATZ]
Aug 26 15:17:06.85: [ 1092]: --> [2:OK]
Aug 26 15:17:06.85: [ 1092]: <-- [5:ATE0\r]
Aug 26 15:17:06.86: [ 1092]: --> [4:ATE0]
Aug 26 15:17:06.86: [ 1092]: --> [2:OK]
Aug 26 15:17:06.86: [ 1092]: <-- [5:ATV1\r]
Aug 26 15:17:06.87: [ 1092]: --> [2:OK]
Aug 26 15:17:06.87: [ 1092]: <-- [5:ATQ0\r]
Aug 26 15:17:06.88: [ 1092]: --> [2:OK]
Aug 26 15:17:06.88: [ 1092]: <-- [7:ATS0=0\r]
Aug 26 15:17:06.89: [ 1092]: --> [2:OK]
Aug 26 15:17:06.89: [ 1092]: <-- [7:ATS8=2\r]
Aug 26 15:17:06.90: [ 1092]: --> [2:OK]
Aug 26 15:17:06.90: [ 1092]: <-- [8:ATS7=60\r]
Aug 26 15:17:06.91: [ 1092]: --> [2:OK]
Aug 26 15:17:06.91: [ 1092]: <-- [9:AT+FLO=1\r]
Aug 26 15:17:06.92: [ 1092]: --> [2:OK]
Aug 26 15:17:06.92: [ 1092]: <-- [6:AT&D3\r]
Aug 26 15:17:06.93: [ 1092]: --> [2:OK]
Aug 26 15:17:06.93: [ 1092]: <-- [6:AT&C1\r]
Aug 26 15:17:06.94: [ 1092]: --> [2:OK]
Aug 26 15:17:06.94: [ 1092]: <-- [12:AT+FCLASS=1\r]
Aug 26 15:17:06.95: [ 1092]: --> [2:OK]
Aug 26 15:17:06.95: [ 1092]: <-- [5:ATM0\r]
Aug 26 15:17:06.96: [ 1092]: --> [2:OK]
Aug 26 15:17:06.96: [ 1092]: MODEM input buffering enabled
Aug 26 15:17:06.96: [ 1092]: <-- [12:AT+FCLASS=1\r]
Aug 26 15:17:07.07: [ 1092]: --> [2:OK]
Aug 26 15:17:07.07: [ 1092]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Aug 26 15:17:07.07: [ 1092]: DIAL 7961336
Aug 26 15:17:07.07: [ 1092]: <-- [12:ATDT7961336\r]
Aug 26 15:17:42.28: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:42.28: [ 1092]: MODEM input buffering disabled
Aug 26 15:17:43.66: [ 1092]: --> HDLC<13:FF C0 04 B5 00 6C 05 00 00 00 00 1C 75>
Aug 26 15:17:43.66: [ 1092]: --> [2:OK]
Aug 26 15:17:43.66: [ 1092]: REMOTE NSF "AD 00 36 A0 00 00 00 00 38"
Aug 26 15:17:43.66: [ 1092]: NSF remote fax equipment: HP
Aug 26 15:17:43.66: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:17:43.67: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:44.36: [ 1092]: --> HDLC<25:FF C0 02 6C CC CC 8C 04 6C 9C EC 04 6C 4C 6C 04
04 04 04 04 04 04 04 AD A7>
Aug 26 15:17:44.36: [ 1092]: --> [2:OK]
Aug 26 15:17:44.36: [ 1092]: REMOTE CSI "626 796 1336"
Aug 26 15:17:44.36: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:17:44.37: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:44.80: [ 1092]: --> HDLC<15:FF C8 01 00 77 1F 23 01 49 01 01 19 00 3A A4>
Aug 26 15:17:44.80: [ 1092]: --> [2:OK]
Aug 26 15:17:44.80: [ 1092]: REMOTE best rate 14400 bit/s
Aug 26 15:17:44.80: [ 1092]: REMOTE max page width 1728 pixels in 215 mm
Aug 26 15:17:44.80: [ 1092]: REMOTE max unlimited page length
Aug 26 15:17:44.80: [ 1092]: REMOTE best vres 7.7 line/mm
Aug 26 15:17:44.80: [ 1092]: REMOTE best format 2-D MMR
Aug 26 15:17:44.80: [ 1092]: REMOTE supports T.30 Annex A, ECM
Aug 26 15:17:44.80: [ 1092]: REMOTE best 0 ms/scanline
Aug 26 15:17:44.80: [ 1092]: USE 14400 bit/s
Aug 26 15:17:44.80: [ 1092]: USE 0 ms/scanline
Aug 26 15:17:44.80: [ 1092]: SEND file "docq/doc50.ps;71"
Aug 26 15:17:44.80: [ 1092]: USE page width 1728 pixels in 215 mm
Aug 26 15:17:44.80: [ 1092]: USE unlimited page length
Aug 26 15:17:44.80: [ 1092]: USE 7.7 line/mm
Aug 26 15:17:44.80: [ 1092]: USE 2-D MR
Aug 26 15:17:44.80: [ 1092]: SEND training at v.17 14400 bit/s
Aug 26 15:17:44.80: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:17:45.66: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:45.66: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:17:45.66: [ 1092]: <-- data [23]
Aug 26 15:17:45.66: [ 1092]: <-- data [2]
Aug 26 15:17:45.67: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:45.67: [ 1092]: <-- HDLC<6:FF C8 C1 00 47 1E>
Aug 26 15:17:45.67: [ 1092]: <-- data [6]
Aug 26 15:17:45.67: [ 1092]: <-- data [2]
Aug 26 15:17:46.76: [ 1092]: --> [2:OK]
Aug 26 15:17:46.76: [ 1092]: DELAY 75 ms
Aug 26 15:17:46.84: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:17:46.84: [ 1092]: <-- [11:AT+FTM=145\r]
Aug 26 15:17:46.85: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:46.85: [ 1092]: <-- data [1024]
Aug 26 15:17:46.85: [ 1092]: <-- data [1024]
Aug 26 15:17:46.85: [ 1092]: <-- data [652]
Aug 26 15:17:46.85: [ 1092]: <-- data [2]
Aug 26 15:17:49.98: [ 1092]: --> [2:OK]
Aug 26 15:17:49.98: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:17:49.98: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:17:50.10: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:51.37: [ 1092]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:17:51.37: [ 1092]: --> [2:OK]
Aug 26 15:17:51.37: [ 1092]: DELAY 1500 ms
Aug 26 15:17:52.87: [ 1092]: SEND training at v.17 12000 bit/s
Aug 26 15:17:52.87: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:17:53.73: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:53.73: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:17:53.73: [ 1092]: <-- data [23]
Aug 26 15:17:53.73: [ 1092]: <-- data [2]
Aug 26 15:17:53.74: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:53.74: [ 1092]: <-- HDLC<6:FF C8 C1 00 57 1E>
Aug 26 15:17:53.74: [ 1092]: <-- data [6]
Aug 26 15:17:53.74: [ 1092]: <-- data [2]
Aug 26 15:17:54.83: [ 1092]: --> [2:OK]
Aug 26 15:17:54.83: [ 1092]: DELAY 75 ms
Aug 26 15:17:54.91: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:17:54.91: [ 1092]: <-- [11:AT+FTM=121\r]
Aug 26 15:17:54.92: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:54.92: [ 1092]: <-- data [1024]
Aug 26 15:17:54.92: [ 1092]: <-- data [1024]
Aug 26 15:17:54.92: [ 1092]: <-- data [202]
Aug 26 15:17:54.92: [ 1092]: <-- data [2]
Aug 26 15:17:58.06: [ 1092]: --> [2:OK]
Aug 26 15:17:58.06: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:17:58.06: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:17:58.18: [ 1092]: --> [7:CONNECT]
Aug 26 15:17:59.44: [ 1092]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:17:59.44: [ 1092]: --> [2:OK]
Aug 26 15:17:59.44: [ 1092]: DELAY 1500 ms
Aug 26 15:18:00.94: [ 1092]: SEND training at v.17 9600 bit/s
Aug 26 15:18:00.94: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:18:01.80: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:01.80: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:18:01.80: [ 1092]: <-- data [23]
Aug 26 15:18:01.80: [ 1092]: <-- data [2]
Aug 26 15:18:01.81: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:01.81: [ 1092]: <-- HDLC<6:FF C8 C1 00 67 1E>
Aug 26 15:18:01.81: [ 1092]: <-- data [6]
Aug 26 15:18:01.81: [ 1092]: <-- data [2]
Aug 26 15:18:02.90: [ 1092]: --> [2:OK]
Aug 26 15:18:02.90: [ 1092]: DELAY 75 ms
Aug 26 15:18:02.98: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:18:02.98: [ 1092]: <-- [10:AT+FTM=97\r]
Aug 26 15:18:02.99: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:02.99: [ 1092]: <-- data [1024]
Aug 26 15:18:02.99: [ 1092]: <-- data [776]
Aug 26 15:18:02.99: [ 1092]: <-- data [2]
Aug 26 15:18:06.13: [ 1092]: --> [2:OK]
Aug 26 15:18:06.13: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:18:06.13: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:18:06.25: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:07.52: [ 1092]: --> HDLC<5:FF C8 22 67 DD>
Aug 26 15:18:07.52: [ 1092]: --> [2:OK]
Aug 26 15:18:07.52: [ 1092]: DELAY 1500 ms
Aug 26 15:18:09.02: [ 1092]: SEND training at v.17 7200 bit/s
Aug 26 15:18:09.02: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:18:09.88: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:09.88: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:18:09.88: [ 1092]: <-- data [23]
Aug 26 15:18:09.88: [ 1092]: <-- data [2]
Aug 26 15:18:09.89: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:09.89: [ 1092]: <-- HDLC<6:FF C8 C1 00 77 1E>
Aug 26 15:18:09.89: [ 1092]: <-- data [6]
Aug 26 15:18:09.89: [ 1092]: <-- data [2]
Aug 26 15:18:10.98: [ 1092]: --> [2:OK]
Aug 26 15:18:10.98: [ 1092]: DELAY 75 ms
Aug 26 15:18:11.06: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:18:11.06: [ 1092]: <-- [10:AT+FTM=73\r]
Aug 26 15:18:11.07: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:11.07: [ 1092]: <-- data [1024]
Aug 26 15:18:11.07: [ 1092]: <-- data [326]
Aug 26 15:18:11.07: [ 1092]: <-- data [2]
Aug 26 15:18:14.22: [ 1092]: --> [2:OK]
Aug 26 15:18:14.22: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:18:14.22: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:18:14.34: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:15.61: [ 1092]: --> HDLC<5:FF C8 21 57 BE>
Aug 26 15:18:15.61: [ 1092]: --> [2:OK]
Aug 26 15:18:15.61: [ 1092]: TRAINING succeeded
Aug 26 15:18:15.61: [ 1092]: DELAY 75 ms
Aug 26 15:18:15.69: [ 1092]: <-- [10:AT+FTM=74\r]
Aug 26 15:18:15.70: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:15.70: [ 1092]: SEND begin page
Aug 26 15:18:15.70: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:18:15.70: [ 1092]: <-- data [1025]
Aug 26 15:18:15.70: [ 1092]: <-- data [1025]
Aug 26 15:18:15.70: [ 1092]: <-- data [1037]
Aug 26 15:18:15.70: [ 1092]: <-- data [1030]
Aug 26 15:18:15.70: [ 1092]: <-- data [1029]
Aug 26 15:18:16.16: [ 1092]: <-- data [1035]
Aug 26 15:18:16.16: [ 1092]: <-- data [1031]
Aug 26 15:18:16.80: [ 1092]: <-- data [1032]
Aug 26 15:18:17.92: [ 1092]: <-- data [1037]
Aug 26 15:18:18.86: [ 1092]: <-- data [1041]
Aug 26 15:18:20.21: [ 1092]: <-- data [1034]
Aug 26 15:18:21.33: [ 1092]: <-- data [1039]
Aug 26 15:18:22.43: [ 1092]: <-- data [1031]
Aug 26 15:18:23.71: [ 1092]: <-- data [1027]
Aug 26 15:18:24.81: [ 1092]: <-- data [1028]
Aug 26 15:18:25.92: [ 1092]: <-- data [1030]
Aug 26 15:18:26.86: [ 1092]: <-- data [1031]
Aug 26 15:18:28.14: [ 1092]: <-- data [273]
Aug 26 15:18:28.44: [ 1092]: SENT 17680 bytes of data
Aug 26 15:18:28.44: [ 1092]: SEND 2D RTC
Aug 26 15:18:28.44: [ 1092]: <-- data [30]
Aug 26 15:18:28.44: [ 1092]: <-- data [2]
Aug 26 15:18:28.44: [ 1092]: SEND end page
Aug 26 15:18:35.78: [ 1092]: --> [2:OK]
Aug 26 15:18:35.78: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:18:35.78: [ 1092]: DELAY 200 ms
Aug 26 15:18:35.98: [ 1092]: SEND send EOP (no more pages or documents)
Aug 26 15:18:35.98: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:18:36.84: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:36.84: [ 1092]: <-- HDLC<3:FF C8 F4>
Aug 26 15:18:36.84: [ 1092]: <-- data [3]
Aug 26 15:18:36.84: [ 1092]: <-- data [2]
Aug 26 15:18:37.16: [ 1092]: --> [2:OK]
Aug 26 15:18:37.16: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:18:37.26: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:38.52: [ 1092]: --> HDLC<5:FF C8 32 75 EC>
Aug 26 15:18:38.52: [ 1092]: --> [2:OK]
Aug 26 15:18:38.52: [ 1092]: SEND recv RTN (retrain negative)
Aug 26 15:18:38.52: [ 1092]: SEND training at v.27ter 4800 bit/s
Aug 26 15:18:38.52: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:18:39.38: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:39.38: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:18:39.38: [ 1092]: <-- data [23]
Aug 26 15:18:39.38: [ 1092]: <-- data [2]
Aug 26 15:18:39.39: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:39.39: [ 1092]: <-- HDLC<6:FF C8 C1 00 53 1E>
Aug 26 15:18:39.39: [ 1092]: <-- data [6]
Aug 26 15:18:39.39: [ 1092]: <-- data [2]
Aug 26 15:18:40.48: [ 1092]: --> [2:OK]
Aug 26 15:18:40.48: [ 1092]: DELAY 75 ms
Aug 26 15:18:40.56: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:18:40.56: [ 1092]: <-- [10:AT+FTM=48\r]
Aug 26 15:18:40.84: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:40.84: [ 1092]: <-- data [900]
Aug 26 15:18:40.84: [ 1092]: <-- data [2]
Aug 26 15:18:43.34: [ 1092]: --> [2:OK]
Aug 26 15:18:43.34: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:18:43.34: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:18:43.47: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:44.74: [ 1092]: --> HDLC<5:FF C8 21 57 BE>
Aug 26 15:18:44.74: [ 1092]: --> [2:OK]
Aug 26 15:18:44.74: [ 1092]: TRAINING succeeded
Aug 26 15:18:44.74: [ 1092]: DELAY 75 ms
Aug 26 15:18:44.82: [ 1092]: <-- [10:AT+FTM=48\r]
Aug 26 15:18:44.83: [ 1092]: --> [7:CONNECT]
Aug 26 15:18:44.83: [ 1092]: SEND begin page
Aug 26 15:18:44.83: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:18:44.83: [ 1092]: <-- data [1025]
Aug 26 15:18:44.83: [ 1092]: <-- data [1025]
Aug 26 15:18:44.83: [ 1092]: <-- data [1037]
Aug 26 15:18:44.83: [ 1092]: <-- data [1030]
Aug 26 15:18:44.83: [ 1092]: <-- data [1029]
Aug 26 15:18:45.91: [ 1092]: <-- data [1035]
Aug 26 15:18:45.91: [ 1092]: <-- data [1031]
Aug 26 15:18:46.87: [ 1092]: <-- data [1032]
Aug 26 15:18:48.55: [ 1092]: <-- data [1037]
Aug 26 15:18:50.18: [ 1092]: <-- data [1041]
Aug 26 15:18:51.94: [ 1092]: <-- data [1034]
Aug 26 15:18:53.62: [ 1092]: <-- data [1039]
Aug 26 15:18:55.51: [ 1092]: <-- data [1031]
Aug 26 15:18:57.19: [ 1092]: <-- data [1027]Aug 26 15:18:58.84: [ 1092]: <-- data [1028]
Aug 26 15:19:00.28: [ 1092]: <-- data [1030]
Aug 26 15:19:02.15: [ 1092]: <-- data [1031]
Aug 26 15:19:03.83: [ 1092]: <-- data [273]
Aug 26 15:19:04.28: [ 1092]: SENT 17680 bytes of data
Aug 26 15:19:04.28: [ 1092]: SEND 2D RTC
Aug 26 15:19:04.28: [ 1092]: <-- data [30]
Aug 26 15:19:04.28: [ 1092]: <-- data [2]
Aug 26 15:19:04.28: [ 1092]: SEND end page
Aug 26 15:19:15.34: [ 1092]: --> [2:OK]
Aug 26 15:19:15.34: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:19:15.34: [ 1092]: DELAY 200 ms
Aug 26 15:19:15.54: [ 1092]: SEND send EOP (no more pages or documents)
Aug 26 15:19:15.54: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:19:16.40: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:16.40: [ 1092]: <-- HDLC<3:FF C8 F4>
Aug 26 15:19:16.40: [ 1092]: <-- data [3]
Aug 26 15:19:16.40: [ 1092]: <-- data [2]
Aug 26 15:19:16.72: [ 1092]: --> [2:OK]
Aug 26 15:19:16.72: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:19:16.82: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:18.09: [ 1092]: --> HDLC<5:FF C8 32 75 EC>
Aug 26 15:19:18.09: [ 1092]: --> [2:OK]
Aug 26 15:19:18.09: [ 1092]: SEND recv RTN (retrain negative)
Aug 26 15:19:18.09: [ 1092]: SEND training at v.27ter fallback mode 2400 bit/s
Aug 26 15:19:18.09: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:19:18.95: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:18.95: [ 1092]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 16 2E 96 B6 CA 04 64
04 86 EE 86 E6 F6 2A>
Aug 26 15:19:18.95: [ 1092]: <-- data [23]
Aug 26 15:19:18.95: [ 1092]: <-- data [2]
Aug 26 15:19:18.96: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:18.96: [ 1092]: <-- HDLC<6:FF C8 C1 00 43 1E>
Aug 26 15:19:18.96: [ 1092]: <-- data [6]
Aug 26 15:19:18.96: [ 1092]: <-- data [2]
Aug 26 15:19:20.05: [ 1092]: --> [2:OK]
Aug 26 15:19:20.05: [ 1092]: DELAY 75 ms
Aug 26 15:19:20.13: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:19:20.13: [ 1092]: <-- [10:AT+FTM=24\r]
Aug 26 15:19:20.14: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:20.14: [ 1092]: <-- data [450]
Aug 26 15:19:20.14: [ 1092]: <-- data [2]
Aug 26 15:19:22.94: [ 1092]: --> [2:OK]
Aug 26 15:19:22.94: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:19:22.94: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:19:23.09: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:24.35: [ 1092]: --> HDLC<5:FF C8 21 57 BE>
Aug 26 15:19:24.35: [ 1092]: --> [2:OK]
Aug 26 15:19:24.35: [ 1092]: TRAINING succeeded
Aug 26 15:19:24.35: [ 1092]: DELAY 75 ms
Aug 26 15:19:24.43: [ 1092]: <-- [10:AT+FTM=24\r]
Aug 26 15:19:24.44: [ 1092]: --> [7:CONNECT]
Aug 26 15:19:24.44: [ 1092]: SEND begin page
Aug 26 15:19:24.44: [ 1092]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Aug 26 15:19:24.44: [ 1092]: <-- data [1025]
Aug 26 15:19:24.44: [ 1092]: <-- data [1025]
Aug 26 15:19:24.44: [ 1092]: <-- data [1037]
Aug 26 15:19:24.44: [ 1092]: <-- data [1030]
Aug 26 15:19:24.44: [ 1092]: <-- data [1029]
Aug 26 15:19:25.91: [ 1092]: <-- data [1035]
Aug 26 15:19:25.91: [ 1092]: <-- data [1031]
Aug 26 15:19:27.83: [ 1092]: <-- data [1032]
Aug 26 15:19:31.24: [ 1092]: <-- data [1037]
Aug 26 15:19:34.55: [ 1092]: <-- data [1041]
Aug 26 15:19:38.12: [ 1092]: <-- data [1034]
Aug 26 15:19:41.53: [ 1092]: <-- data [1039]
Aug 26 15:19:44.36: [ 1092]: <-- data [1031]
Aug 26 15:19:48.20: [ 1092]: <-- data [1027]
Aug 26 15:19:51.50: [ 1092]: <-- data [1028]
Aug 26 15:19:54.86: [ 1092]: <-- data [1030]
Aug 26 15:19:58.65: [ 1092]: <-- data [1031]
Aug 26 15:20:02.00: [ 1092]: <-- data [273]
Aug 26 15:20:02.91: [ 1092]: SENT 17680 bytes of data
Aug 26 15:20:02.91: [ 1092]: SEND 2D RTC
Aug 26 15:20:02.91: [ 1092]: <-- data [30]
Aug 26 15:20:02.91: [ 1092]: <-- data [2]
Aug 26 15:20:02.91: [ 1092]: SEND end page
Aug 26 15:20:24.76: [ 1092]: --> [2:OK]
Aug 26 15:20:24.76: [ 1092]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Aug 26 15:20:24.76: [ 1092]: DELAY 200 ms
Aug 26 15:20:24.96: [ 1092]: SEND send EOP (no more pages or documents)
Aug 26 15:20:24.96: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:20:25.82: [ 1092]: --> [7:CONNECT]
Aug 26 15:20:25.82: [ 1092]: <-- HDLC<3:FF C8 F4>
Aug 26 15:20:25.82: [ 1092]: <-- data [3]
Aug 26 15:20:25.82: [ 1092]: <-- data [2]
Aug 26 15:20:26.14: [ 1092]: --> [2:OK]
Aug 26 15:20:26.14: [ 1092]: <-- [9:AT+FRH=3\r]
Aug 26 15:20:26.25: [ 1092]: --> [7:CONNECT]
Aug 26 15:20:27.51: [ 1092]: --> HDLC<5:FF C8 32 75 EC>
Aug 26 15:20:27.51: [ 1092]: --> [2:OK]
Aug 26 15:20:27.51: [ 1092]: SEND recv RTN (retrain negative)
Aug 26 15:20:27.51: [ 1092]: <-- [9:AT+FTH=3\r]
Aug 26 15:20:28.37: [ 1092]: --> [7:CONNECT]
Aug 26 15:20:28.37: [ 1092]: <-- HDLC<3:FF C8 DF>
Aug 26 15:20:28.37: [ 1092]: <-- data [3]
Aug 26 15:20:28.37: [ 1092]: <-- data [2]
Aug 26 15:20:28.69: [ 1092]: --> [2:OK]
Aug 26 15:20:28.69: [ 1092]: MODEM input buffering enabled
Aug 26 15:20:28.69: [ 1092]: <-- [5:ATH0\r]
Aug 26 15:20:29.76: [ 1092]: --> [2:OK]
Aug 26 15:20:29.76: [ 1092]: MODEM set DTR OFF
Aug 26 15:20:29.76: [ 1092]: SESSION END