Re: [hylafax-users] Fax receive EOP or MPN problem

[John Sved <JohnSved@compuserve.com>]

Title:

Giulio Orsero wrote:
>  
> On Thu, 17 Jul 2003 18:47:53 +0200, John Sved <JohnSved@compuserve.com>
> wrote:
>
>
> > Class1TCFMinRun:    1000        # min run is 2/3rds of TCF duration
> >
> > ClassSwitchingCmd:    <delay:7>
> >   
> This worked  :-) 
> > Jul 17 19:23:46.27: [ 2003]: MODEM set XON/XOFF/FLUSH: input ignored, output
> > generated
> > Jul 17 19:23:46.27: [ 2003]: <-- [4:yes\r]
> > Jul 17 19:24:16.27: [ 2003]: MODEM TIMEOUT: reading line from modem
> > Jul 17 19:24:16.27: [ 2003]: MODEM <Timeout>
> >   
>
> That "yes" is clearly wrong, right now I cannot test the correct syntax,
> please try adding  " and ":
>
> Class1SwitchingCmd:     "<delay:7>"
>
> you should see something like
>
> DELAY 70 in place of "yes\r"

Delay 75ms


FYI  the config.ttyS0   is now :

# $Id: rc288dpi-1,v 1.4 2002/04/07 20:29:26 darren Exp $
#
# HylaFAX Facsimile Software


#
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800        firmware rev ???
#    Microcom DeskPorte 28.8S    firmware rev V1.100K-V34_DS
#    PPI PM288FXMT        firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
#
CountryCode:        49
AreaCode:        yyyy
FAXNumber:        "+49 xxxx xxxxx"
LongDistancePrefix:    0
InternationalPrefix:    00
DialStringRules:    etc/dialrules
ServerTracing:        527
SessionTracing:        527
RecvFileMode:        0600
LogFileMode:        0600
DeviceMode:        0600
RingsBeforeAnswer:    1
SpeakerVolume:        high
GettyArgs:        "-h %l dx_%s"
LocalIdentifier:    "zzzzzzzzzzz"
TagLineFont:        etc/lutRS18.pcf
TagLineFormat:        "From %%l|%c|Page %%P of %%T"
MaxRecvPages:        25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:        Class1        # use this to supply a hint
ModemRate:        19200        # rate for DCE-DTE communication
#ModemFlowControl:    rtscts        # default  rtscts
ModemFlowControl:    xonxoff        #
#ModemResetCmds:    AT&V1
#ModemRecvFillOrder:    LSB2MSB
#ModemSendFillOrder:    LSB2MSB
#
#ModemNoFlowCmd:    AT&K0        # setup no flow control
#ModemHardFlowCmd:    AT&K3        # setup hardware flow control
ModemSoftFlowCmd:    AT&K4        # setup software flow control
ModemSetupDTRCmd:    AT&D2        # setup so DTR drop resets modem
ModemSetupDCDCmd:    AT&C1        # setup so DCD reflects carrier (or
not)

#
ModemMfrQueryCmd:    !Rockwell
ModemModelQueryCmd:    !RC288DPi
ModemRevQueryCmd:    ATI3        # product information
#
ModemDialCmd:        ATDT0%s        # T for tone dialing


Class1Cmd:        AT+FCLASS=1    # command to enter class 1
Class1PPMWaitCmd:    AT+FTS=7    # command to stop and wait before PPM
Class1TCFWaitCmd:    AT+FTS=7    # command to stop and wait before TCF
Class1EOPWaitCmd:    AT+FTS=9    # command to stop and wait before EOP
Class1MsgRecvHackCmd:    ""        # command to avoid +FCERROR before image
Class1TCFResponseDelay:    75        # 75ms delay between recv TCF &
response
Class1SendMsgDelay:    75        # 75ms delay after training
Class1SwitchingCmd:    "<delay:7>"    # silence between HDLC recv and
trans
Class1TrainingRecovery:    1500        # 1.5sec delay after training failure
Class1RecvAbortOK:    200        # wait 200ms for abort response
Class1FrameOverhead:    4        # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer:    40000        # 35+5secs waiting for ident frames
Class1TCFMaxNonZero:    10        # max 10% of data may be non-zero
Class1TCFMinRun:    1000        # min run is 2/3rds of TCF duration




Thanks,

Lee and Giulio


Now my next problem is that SuSEFax is not allowing me to view the incoming
faxes in the received queue.  Viewer "operation not permitted"........ but
that will be another post if I cannot sort it out.