Re: [hylafax-users] problem faxing after version update...!?!

[Holger Raschke <holger.raschke@presse-data.de>]

>>Does this directory exist actually? In your config.faxCAPI you refer to 
>>/var/spool/fax!
>>Where is the config.faxCAPI located?
>>
>>I addition, the spooldir seems to be set to /var/spool/hylafax.
> 
> 
> In config.faxCAPI is located in /var/spool/fax/etc/ and the spool
> directory is set to /var/spool/fax, but as you see above the c2faxrecv
> seems to have the spool dir set to /var/spool/hylafax ?!

Since hylafax version 4.1.3 the spooldir moved to /var/spool/hylafax.
Did you upgrade your SuSE installation which resulted in both path 
beeing there?
Check the hylafax version information in both trees.

> 
>>># default   /var/spool/fax
>>>#
>>>SpoolDir:               /var/spool/fax
>>
>>config.faxCAPI is searched in /var/spool/hylafax/etc!
>>Why do you have different SpoolDir's?
> 
> 
> I don't know why c2faxrecv searches for /var/spool/hylafax whereas in
> config.faxCAPI its /var/spool/fax !?!

Did you try to move config.faxCAPI to the new spooldir?
Don't forget to change the paths in there.

>  
> 
>>> 
>>># default   /var/spool/hylafax/bin/faxrcvd
>>># 
>>>FaxRcvdCmd:             /var/spool/fax/bin/faxrcvd
>>> 
>>># default   /var/spool/hylafax/bin/pollrcvd
>>>#
>>>PollRcvdCmd:             /var/spool/fax/bin/pollrcvd
>>> 
>>># default   ""
>>># 
>>>FaxReceiveUser:         uucp
>>> 
>>># default   ""
>>>#
>>>LogFile:                # /tmp/capifax.log
>>> 
>>># default   0 
>>>#
>>>LogTraceLevel:          0
>>> 
>>># default   0600
>>>#
>>>LogFileMode:            0600
>>> 
>>> 
>>>{
>>> 
>>>    # default   faxCAPI
>>>    #
>>>    HylafaxDeviceName:          faxCAPI
>>> 
>>> 
>>>    # default   0600
>>>    #
>>>    RecvFileMode:               0600
>>> 
>>> 
>>>    # default   ""
>>>    #
>>>    FAXNumber:                  +49.40.77201010
>>> 
>>> 
>>>    # default   ""
>>>    #
>>>    LocalIdentifier:            "ARCUS Dichtelemente GmbH"
>>> 
>>> 
>>>    # default   2
>>>    #
>>>    MaxConcurrentRecvs:         2
>>> 
>>> 
>>>    # default   ""
>>>    #
>>>    OutgoingMSN:                +49.40.7729100
>>
>>Just use an MSN here, e.g. 7729100.
> 
> 
> OK I'll changed it or is it ok to leave it blank?

This depends on your phone installation. Blank is OK if outgoing calls 
are not rejected without presenting a valid MSN.

> 
> 
>>> 
>>> 
>>>    # default   0
>>>    #
>>>    SuppressMSN:                0
>>> 
>>> 
>>>    # default   ""
>>>    #
>>>    NumberPrefix:
>>> 
>>> 
>>>    # default   0
>>>    #
>>>    UseISDNFaxService:          0
>>> 
>>> 
>>>    # default   0
>>>    #
>>>    RingingDuration:            0
>>> 
>>> 
>>>    # ----------- incoming params -----------
>>>    {
>>> 
>>>        # default   1
>>>        #
>>>        Controller:             1
>>> 
>>> 
>>>        # default   0
>>>        #
>>>        AcceptSpeech:           1
>>> 
>>> 
>>>        # default   0
>>>        #
>>>        UseDDI:                 0
>>> 
>>> 
>>>        # default   ""
>>>        #
>>>        DDIOffset:
>>> 
>>> 
>>>        # default   0
>>>        #
>>>        DDILength:              0
>>> 
>>> 
>>>        # default   ""
>>>        #
>>>        IncomingDDIs:
>>> 
>>> 
>>>        # default   ""
>>>        #
>>>        IncomingMSNs:
>>> 
>>> 
>>>        # default   1
>>>        #
>>>        AcceptGlobalCall:   1
>>>    }
>>>}
>>>
>>>But I don't understand why c2faxrecv give a wrong spool directory? And
>>>don't know where to change it? If I run faxsetup again it doesn#t show
>>>the configuration again.
>>
>>First test it with the -C and -q option to point c2faxrecv to a 
>>different path:
>>
>>c2faxrecv -C /var/spool/fax/etc/config.faxCAPI -q /var/spool/fax
> 
> 
> This return a Error: program not dumpable after PR_SET_DUMPABLE :-(
> 
> 
>>If this works, reinstall capi4hylafax with the "-p" option mentioned above.
> 
> 
> Also tried to reinstall capi4linux with -p /var/spool/fax, but the above
> error pesists. :-((

Should be capi4hylafax!

> 
> How can solve this? is it a problem with the hylafax came with SuSe 8.2?

I use SuSe 8.0 and the release shipped with this version works fine.
I didn't try 8.2 yet.

To my mind your errors deal with c4l/c4h. May be you uninstall the 
SuSE-releases and install the versions provided by AVM.

I suggest checking c4l with capitools (capiconn...) to check if basic 
CAPI functions work (incoming and outgoing connections). If this is OK 
proceed with c4h.

--
Holger


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*