Re: [hylafax-users] Waiting for the modem to become ready

["Anthony Diak" <anthonyd@rhsonline.net>]

A quick google search returned this url:
http://rpmfind.net/linux/RPM/redhat/8.0/i386/uucp-1.06.1-45.i386.php

-Anthony Diak
> Hi
> I am missing cu on my linux distribution , any idea where I can download
> source or rpm .Thanks
> ----- Original Message -----
> From: "Anthony Diak" <anthonyd@rhsonline.net>
> To: "Gianluca Trifiletti" <g.trifiletti@Kairosinv.com>
> Cc: <hylafax-users@hylafax.org>
> Sent: Thursday, May 22, 2003 1:57 PM
> Subject: Re: [hylafax-users] Waiting for the modem to become ready
>
>
>> Did you try the part in the setup manual that says to check your modem?
>>
>> "Once you have a modem to use with HylaFAXT first make sure that the
>> modem
>> works for data use. One can not say this enough. If you can not use a
>> communication program such as cu, tip, or kermit, with your modem, do
>> not
>> try to configure it for use with HylaFAXT. This means in particular that
>> you should verify that you have a working cable between your host and
>> modem and that this cable is suitable for use. That is, that the cable
>> has
>> the relevant signals for doing hardware flow control if that is
>> necessary
>> and that it passes the DCD and DTR signals appropriately.
>> Verify that the modem you are using is a fax modem. This can be done by
>> communicating directly with the modem using a communication program such
>> as cu; for example:
>>
>> hyla% cu -l ttyf2
>> Connected
>> at+fclass=?
>> 0,1,2
>> OK
>> ~[hyla].
>> Disconnected
>>
>> The at+fclass=? command asks the modem to report which classes it is
>> capable of supporting. Class 0 is for data use. Class 1, Class 2, and
>> Class 2.0 are for facsimile use. Other classes may be reported, for
>> example, for modems that provide digitized voice support. HylaFAXT can
>> be
>> used with any modem that supports Class 1, Class 2, or Class 2.0. "
>>
>> Also, while you are in cu, you can try dialing out by issuing the
>> following commands:
>>
>> at
>> OK
>> atdt9999999999    (where 9999999999 is the phone number you want to
>> dial)
>>
>> See if the modem works correctly on the phone line, maybe thats the
> problem.
>>
>> -Anthony Diak
>>
>> > Hi ,
>> >
>> >
>> >
>> > I have the same problem, RedHat 8.0, Hylafax 4.1.5 US Robotics
>> faxmodem
>> > 56K
>> > external, this modem is configurable as class 1 or 2.0, in the first
> case
>> > trying to send a fax I get the error "Waiting for the modem to become
>> > ready"
>> > at the prompt ....faxstat Waiting for the modem to become ready.....;
>> in
>> > the
>> > second case, error "No dial tone" at the prompt faxstat "Hylafax
>> running
>> > Modem idle".
>> >
>> > 1st I though was a line problem but the phone works fine on that line;
>> I
>> > don't know what else to do, I put two line in config.ttyS0:
>> ModemDialCmd
>> > ATX3,
>> >
>> > ModemDialCmd:  ATDP0, %s, I tried to send fax from the Windows client
>> by
>> > "sambafax" and by WHFC and from Linux box with send fax -n -d
>> > xxxxxxxxxxxxxxxx  /etc/faxtest.ps.,  the document in both cases went
>> to
>> > docq, stayed there for a while and then moved to sendq even if it had
> not
>> > been sent,  I got an email reporting the above errors; when I tried to
>> > send
>> > fax, I can see the modem led blinking .
>> >
>> > Please help me it is about two weeks I am working at Hylafax without
>> > significant results.
>> >
>> > I attach the error log of Hylafax and the configuration file for the
> modem
>> > ttyS0.
>> >
>> >
>> >
>> >
>> >
>> > This is the log:
>> >
>> >
>> >
>> >
>> >
>> > May 22 16:32:52.49: [ 2025]: SESSION BEGIN 00000039 00447986058729
>> > May 22 16:32:52.49: [ 2025]: HylaFAX (tm) Version 4.1.5
>> > May 22 16:32:52.49: [ 2025]: SEND FAX: JOB 2 DEST xxxxxxxxxxx COMMID
>> > 00000039 DEVICE '/dev/ttyS0'
>> > May 22 16:32:52.49: [ 2025]: DELAY 75 ms
>> > May 22 16:32:52.57: [ 2025]: DELAY 2600 ms
>> > May 22 16:32:55.17: [ 2025]: DELAY 10 ms
>> > May 22 16:32:55.18: [ 2025]: <-- [4:ATZ\r]
>> > May 22 16:32:55.31: [ 2025]: --> [2:OK]
>> > May 22 16:32:55.31: [ 2025]: DELAY 3000 ms
>> > May 22 16:32:58.31: [ 2025]: <-- [5:ATE0\r]
>> > May 22 16:32:58.45: [ 2025]: --> [4:ATE0]
>> > May 22 16:32:58.45: [ 2025]: --> [2:OK]
>> > May 22 16:32:58.45: [ 2025]: <-- [5:ATV1\r]
>> > May 22 16:32:58.58: [ 2025]: --> [2:OK]
>> > May 22 16:32:58.58: [ 2025]: <-- [7:ATQ0X4\r]
>> > May 22 16:32:58.71: [ 2025]: --> [2:OK]
>> > May 22 16:32:58.71: [ 2025]: <-- [7:ATS0=0\r]
>> > May 22 16:32:58.85: [ 2025]: --> [2:OK]
>> > May 22 16:32:58.85: [ 2025]: <-- [7:ATS8=2\r]
>> > May 22 16:32:58.98: [ 2025]: --> [2:OK]
>> > May 22 16:32:58.98: [ 2025]: <-- [8:ATS7=60\r]
>> > May 22 16:32:59.12: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.12: [ 2025]: <-- [12:AT&H2&I2&R1\r]
>> > May 22 16:32:59.26: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.26: [ 2025]: <-- [11:ATS13=1&D2\r]
>> > May 22 16:32:59.39: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.39: [ 2025]: <-- [6:AT&C1\r]
>> > May 22 16:32:59.53: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.53: [ 2025]: <-- [12:AT+FCLASS=1\r]
>> > May 22 16:32:59.66: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.66: [ 2025]: <-- [12:AT+FCLASS=0\r]
>> > May 22 16:32:59.80: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.80: [ 2025]: <-- [5:ATM0\r]
>> > May 22 16:32:59.93: [ 2025]: --> [2:OK]
>> > May 22 16:32:59.94: [ 2025]: <-- [12:AT+FCLASS=1\r]
>> > May 22 16:33:00.17: [ 2025]: --> [2:OK]
>> > May 22 16:33:00.17: [ 2025]: DIAL 07986058729
>> > May 22 16:33:00.17: [ 2025]: <-- [16:ATDTxxxxxxxxxxxx\r]
>> > May 22 16:33:05.30: [ 2025]: --> [12:NO DIAL TONE]
>> > May 22 16:33:05.30: [ 2025]: SEND FAILED: JOB 2 DEST xxxxxxxxxxx ERR
>> No
>> > local dialtone
>> > May 22 16:33:05.30: [ 2025]: <-- [5:ATH0\r]
>> > May 22 16:33:05.53: [ 2025]: --> [2:OK]
>> > May 22 16:33:05.53: [ 2025]: SESSION END
>> >
>> >
>> >
>> >
>> >
>> > And this is the modem configuration:
>> >
>> >
>> >
>> > # $Id: usr-xon,v 1.9 2002/09/13 16:55:15 darren Exp $
>> > #
>> > # HylaFAX Facsimile Software
>> > #
>> > # Copyright (c) 1990-1996 Sam Leffler
>> > # Copyright (c) 1991-1996 Silicon Graphics, Inc.
>> > # HylaFAX is a trademark of Silicon Graphics, Inc.
>> > #
>> > # Permission to use, copy, modify, distribute, and sell this software
> and
>> > # its documentation for any purpose is hereby granted without fee,
>> > provided
>> > # that (i) the above copyright notices and this permission notice
>> appear
>> > in
>> > # all copies of the software and related documentation, and (ii) the
> names
>> > of
>> > # Sam Leffler and Silicon Graphics may not be used in any advertising
>> or
>> > # publicity relating to the software without the specific, prior
>> written
>> > # permission of Sam Leffler and Silicon Graphics.
>> > #
>> > # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
>> > # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
>> > # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
>> > #
>> > # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
>> > # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY
> KIND,
>> > # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
>> PROFITS,
>> > # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY
>> THEORY
>> > OF
>> > # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
>> PERFORMANCE
>> > # OF THIS SOFTWARE.
>> > #
>> >
>> > #
>> > # Configuration for using the Class 1 command interface with
>> > # a USR Courier or Sportster modem and XON/XOFF flow control.
>> > #
>> > #
>> > CountryCode:            0044
>> > AreaCode:         020
>> > FAXNumber:        0044.020.xxxxxxxxxxx
>> > LongDistancePrefix:     0
>> > InternationalPrefix:    0039
>> > DialStringRules:  etc/dialrules
>> > ServerTracing:          1
>> > SessionTracing:         11
>> > RecvFileMode:           0600
>> > LogFileMode:            0600
>> > DeviceMode:       0600
>> > RingsBeforeAnswer:      2
>> > SpeakerVolume:          off
>> > GettyArgs:        "-h ttyS0 19200"
>> > LocalIdentifier:  xxxxxxxxxxxxxxxxx
>> > TagLineFont:            etc/lutRS18.pcf
>> > TagLineFormat:          "From %%l|%c|Page %%P of %%T"
>> > NoCarrierRetrys:  3
>> > MaxRecvPages:           30
>> > #
>> > #
>> > # Modem-related stuff: should reflect modem command interface
>> > # and hardware connection/cabling (e.g. flow control).
>> > #
>> > ModemType:        Class1            # use class 1 interface
>> > ModemRate:        19200       # rate for DCE-DTE communication
>> > ModemFlowControl: xonxoff           # software flow control
>> > #
>> > ModemResetCmd:          ATX3
>> > ModemSetupDTRCmd: ATS13=1&D2  # setup so DTR drop resets modem
>> > ModemSetupDCDCmd: AT&C1       # setup so DCD reflects carrier (or not)
>> > ModemNoFlowCmd:         AT&H0&I0&R1 # setup modem for no flow control
>> > ModemHardFlowCmd: AT&H1&I0&R2 # setup modem for hardware flow control
>> > ModemSoftFlowCmd: AT&H2&I2&R1 # setup modem for software flow control
>> > ModemResultCodesCmd:    ATQ0X3            # enable result codes
>> > ModemDialCmd:           ATDP0, %s       # enable tone dialing
>> > #
>> > ModemMfrQueryCmd: !USR
>> > ModemModelQueryCmd:     ATI3
>> > ModemRevQueryCmd: ATI7        # XXX returns a multi-line result
>> > #
>> > # When AT+FCLASS=1 is issued the modem automatically switches
>> > # to software flow control; these parameters let the fax software
>> > # reset flow control as needed after entering Class 1.
>> > #
>> > Class1NFLOCmd:          AT&H0&I0&R1 # setup modem for no flow control
>> > Class1HFLOCmd:          AT&H1&I0&R2 # setup modem for hardware flow
>> > control
>> > Class1SFLOCmd:          ""          # modem does this automatically
>> > #
>> > # This should resolve "DIS/DTC received 3 times" errors:
>> > #
>> > Class1ResponseWaitCmd:  AT+FRS=1    # wait after sending TCF for
> response
>> > #
>> > # The remainder of this configuration is included so that the
>> > # modem "idles" in Class 0 while not sending or receiving facsimile.
>> > #
>> > ModemSetupAACmd:  AT+FCLASS=0 # leave modem idling in class 0
>> > ModemAnswerCmd:         AT+FCLASS=1A      # answer in Class 1
>> > #
>> > # Disables the reporting of bad frames by the modem.  This
>> > # overcomes a firmware problem in the x2 and V90 Sportsters.
>> > # It is not necessary for the Courier modem.
>> > #
>> > Class2NRCmd:    AT+FNR=1,1,1,0
>> >
>> >
>> >
>> >
>> > Thank you very much in advance and sorry for my English.
>> >
>> >
>> >
>> > Luca
>> >
>> >
>> >
>> >
>> >
>> >
>>
>>
>> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
>>   To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
>>  On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org <
> /dev/null
>>   *To learn about commercial HylaFAX(tm) support, mail
>> sales@hylafax.org.*
>>
>>
>
>


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*