[hylafax-users] Phase B error (code 70)

["Giorgio Biondi" <gbiondi@tech2.it>]

Hi folks,

for more information, I sent you, a log extract on /var/log/message and
/var/spool/hylafax/log, after set
a tracesession to 0xFFF.
Today send a help-message to Zyxel support, but I have few hope...
You can suggest some hints for this?


/var/spool/hylafax/log
May 15 08:29:52.99: [ 6221]: SESSION BEGIN 00026390 390102703320
May 15 08:29:52.99: [ 6221]: HylaFAX (tm) Version 4.1.5
May 15 08:29:52.99: [ 6221]: <-- [4:ATA\r]
May 15 08:29:52.99: [ 6221]: --> [13:FM:273 TO:360]
May 15 08:29:53.14: [ 6221]: --> [11:FAX 2 PIANO]
May 15 08:29:53.14: [ 6221]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyD001'
May 15 08:29:53.14: [ 6221]: STATE CHANGE: ANSWERING -> RECEIVING
May 15 08:29:53.14: [ 6221]: MODEM input buffering enabled
May 15 08:29:53.14: [ 6221]: RECV FAX: begin
May 15 08:29:58.45: [ 6221]: --> [10:NO CARRIER]
May 15 08:29:58.45: [ 6221]: REMOTE HANGUP: Unspecified Receive Phase B
error (code 70)
May 15 08:29:58.45: [ 6221]: RECV FAX: Unspecified Receive Phase B error
May 15 08:29:58.45: [ 6221]: RECV FAX: end
May 15 08:29:58.45: [ 6221]: SESSION END

/var/log/message
May 15 08:29:52 faxserver FaxGetty[6221]: MODEM input buffering enabled
May 15 08:29:52 faxserver FaxGetty[6221]: --> [4:RING]
May 15 08:29:52 faxserver FaxGetty[6221]: MODEM input buffering enabled
May 15 08:29:53 faxserver FaxGetty[6221]: ANSWER: FAX CONNECTION  DEVICE
'/dev/ttyD001'
May 15 08:29:58 faxserver FaxGetty[6221]: <-- [5:ATH0\r]
May 15 08:29:58 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:29:58 faxserver FaxGetty[6221]: MODEM set DTR OFF
May 15 08:29:58 faxserver FaxGetty[6221]: MODEM set DTR OFF
May 15 08:29:58 faxserver FaxGetty[6221]: DELAY 75 ms
May 15 08:29:58 faxserver FaxGetty[6221]: MODEM set DTR ON
May 15 08:29:58 faxserver FaxGetty[6221]: DELAY 2600 ms
May 15 08:30:01 faxserver FaxGetty[6221]: MODEM set baud rate: 38400 baud,
input flow RTS/CTS, output flow RTS/CTS
May 15 08:30:01 faxserver FaxGetty[6221]: DELAY 10 ms
May 15 08:30:01 faxserver FaxGetty[6221]: MODEM flush i/o
May 15 08:30:01 faxserver FaxGetty[6221]: <-- [4:ATZ\r]
May 15 08:30:01 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:01 faxserver FaxGetty[6221]: DELAY 3000 ms
May 15 08:30:04 faxserver FaxGetty[6221]: <--
[51:AT&o1x3b40&B1&N0&S0S18=4S38.3=1&L1s119.1=0s118.6=1\r]
May 15 08:30:04 faxserver FaxGetty[6221]: -->
[50:AT&o1x3b40&B1&N0&S0S18=4S38.3=1&L1s119.1=0s118.6=1]
May 15 08:30:04 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:04 faxserver FaxGetty[6221]: <-- [5:ATE0\r]
May 15 08:30:04 faxserver FaxGetty[6221]: --> [4:ATE0]
May 15 08:30:04 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:04 faxserver FaxGetty[6221]: <-- [5:ATV1\r]
May 15 08:30:04 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:04 faxserver FaxGetty[6221]: <-- [5:ATQ0\r]
May 15 08:30:04 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:04 faxserver FaxGetty[6221]: <-- [7:ATS0=0\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [7:ATS8=2\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [8:ATS7=60\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [6:AT&H3\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [6:AT&D2\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [6:AT&C1\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [12:AT+FCLASS=?\r]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [15:0,1,2,2.0,6,8,Z]
May 15 08:30:05 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports "Data"
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports "Class 1"
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports "Class 2"
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports "Class 2.0"
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports
May 15 08:30:05 faxserver FaxGetty[6221]: MODEM Supports "Voice"
May 15 08:30:05 faxserver FaxGetty[6221]: <-- [14:AT+FCLASS=2.0\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [8:AT+FMI?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [5:ZyXEL]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM: Mfr ZyXEL
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [8:AT+FMM?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [18:E2864  V 3.00a    ]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [8:AT+FMR?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [18:E2864  V 3.00a    ]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM: Model E2864
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM: Revision V 3.00a
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [9:AT+FCC=?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: -->
[43:(0,1),(0-5),(0-2),(0-2),(0,1),(0),(0),(0-7)]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 3.85 line/mm
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 7.7 line/mm
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 2400 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 4800 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 7200 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 9600 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 12000 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 14400 bit/s
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports page width 1728
pixels in 215 mm
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports page width 2048
pixels in 255 mm
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports page width 2432
pixels in 303 mm
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports A4 page length (297
mm)
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports B4 page length (364
mm)
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports unlimited page
length
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 1-D MR
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 2-D MR
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 0 ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 5 ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 10 ms, 5
ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 10 ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 20 ms, 10
ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 20 ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 40 ms, 20
ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 40 ms/scanline
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [9:AT+FCQ=?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [11:(0-2),(0-2)]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:06 faxserver FaxGetty[6221]: MODEM Supports 1D+2D copy quality
checking (but not enabled)
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [9:AT+FAP=?\r]
May 15 08:30:06 faxserver FaxGetty[6221]: --> [5:ERROR]
May 15 08:30:06 faxserver FaxGetty[6221]: <-- [9:AT+FSP=?\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [3:0,1]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [14:AT+FCLASS=2.0\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [9:AT+FLO=2\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [9:AT+FPP=0\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [9:AT+FBO=0\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [10:AT+FCT=30\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [15:AT+FNR=1,1,1,1\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [9:AT+FIE=0\r]
May 15 08:30:07 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:07 faxserver FaxGetty[6221]: <-- [9:AT+FBU=1\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: MODEM ZYXEL E2864/V 3.00a
May 15 08:30:08 faxserver FaxGetty[6221]: <-- [5:ATM0\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: <-- [9:AT+FCR=1\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: <-- [16:AT+FLI="Aprile"\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: <-- [9:AT+FAA=1\r]
May 15 08:30:08 faxserver FaxGetty[6221]: --> [2:OK]
May 15 08:30:08 faxserver FaxGetty[6221]: MODEM input buffering disabled

-----Messaggio originale-----
Da: hylafax-users-bounce@hylafax.org
[mailto:hylafax-users-bounce@hylafax.org]Per conto di Lee Howard
Inviato: mercoledì 14 maggio 2003 16.35
A: gbiondi@tech2.it
Cc: hylafax-users@hylafax.org
Oggetto: Re: [hylafax-users] Phase B error (code 70)


On 2003.05.13 21:32 Giorgio Biondi wrote:
> Hi,
>
> anybody have some idea for solve this problem? The modem is
> Zyxel 2864I with 3.00a firmware (latest). I have try to load
> some firmware from zyxel-ftp-site but no result. This problem
> occours only with latest-generation of fax-machine Lanier...
>
> [root@faxserver log]# cat c00026086
> May 14 00:40:20.72: [19933]: SESSION BEGIN 00026086 390101232359
> May 14 00:40:20.72: [19933]: HylaFAX (tm) Version 4.1.5
> May 14 00:40:20.72: [19933]: <-- [4:ATA\r]
> May 14 00:40:20.72: [19933]: --> [18:FM:22504436 TO:359]
> May 14 00:41:06.39: [19933]: --> [7:+FHS:70]


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*