 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] Zyxel
- To: <hylafax-users@hylafax.org>
- Subject: Re: [hylafax-users] Zyxel
- From: "Paul van Brouwershaven" <paul@vanbrouwershaven.com>
- Date: Fri, 4 Oct 2002 10:53:22 +0200
Additional information:
The full document was not received because:
Missing EOL after 5 seconds (section 3.2/T.4)
> -----Original Message-----
> From: hylafax-users-bounce@hylafax.org
> [mailto:hylafax-users-bounce@hylafax.org] On Behalf Of Paul
> van Brouwershaven
> Sent: Thursday, October 03, 2002 10:41 PM
> To: hylafax-users@hylafax.org
> Subject: [hylafax-users] Zyxel
>
>
> Hi,
>
> When I try to send a fax to hylafax, the server discconect after
> receiving the first page ?
>
> Can someone help me with this problem ?
>
> Modem = Zyxel Omni 56K
> Class = 2.0
>
> ================================================================
> HYLAFAX TRANSFER LOG
> ================================================================
>
> Oct 03 22:17:50.92: [23359]: SESSION BEGIN 00000082 31164262983
> Oct 03 22:17:50.92: [23359]: HylaFAX (tm) Version 4.1.3
> Oct 03 22:17:50.92: [23359]: <-- [4:ATA\r]
> Oct 03 22:18:00.66: [23359]: --> [4:+FCO]
> Oct 03 22:18:00.66: [23359]: ANSWER: FAX CONNECTION DEVICE
> '/dev/ttyS0'
> Oct 03 22:18:00.66: [23359]: RECV FAX: begin
> Oct 03 22:18:00.94: [23359]: --> [27:+FTI:" 0164258126"]
> Oct 03 22:18:00.94: [23359]: REMOTE TSI "0164258126"
> Oct 03 22:18:00.94: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3]
> Oct 03 22:18:00.94: [23359]: REMOTE wants 4800 bit/s
> Oct 03 22:18:00.94: [23359]: REMOTE wants page width 1728
> pixels in 215
> mm
> Oct 03 22:18:00.94: [23359]: REMOTE wants unlimited page length
> Oct 03 22:18:00.94: [23359]: REMOTE wants 3.85 line/mm
> Oct 03 22:18:00.94: [23359]: REMOTE wants 2-D MR
> Oct 03 22:18:00.94: [23359]: --> [2:OK]
> Oct 03 22:18:00.94: [23359]: <-- [7:AT+FDR\r]
> Oct 03 22:18:06.07: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3]
> Oct 03 22:18:06.07: [23359]: REMOTE wants 4800 bit/s
> Oct 03 22:18:06.07: [23359]: REMOTE wants page width 1728
> pixels in 215
> mm
> Oct 03 22:18:06.07: [23359]: REMOTE wants unlimited page length
> Oct 03 22:18:06.07: [23359]: REMOTE wants 3.85 line/mm
> Oct 03 22:18:06.07: [23359]: REMOTE wants 2-D MR
> Oct 03 22:18:06.07: [23359]: --> [7:CONNECT]
> Oct 03 22:18:06.07: [23359]: RECV: begin page
> Oct 03 22:18:06.07: [23359]: RECV: send trigger 022
> Oct 03 22:18:06.07: [23359]: <-- data [1]
> Oct 03 22:19:00.74: [23359]: RECV: 32736 bytes of data, 829
> total lines
> Oct 03 22:19:10.58: [23359]: RECV: 5962 bytes of data, 1082
> total lines
> Oct 03 22:19:11.99: [23359]: --> [16:+FPS:1,441,0,0,0]
> Oct 03 22:19:11.99: [23359]: --> [6:+FET:0]
> Oct 03 22:19:11.99: [23359]: RECV recv MPS (more pages, same document)
> Oct 03 22:19:11.99: [23359]: --> [2:OK]
> Oct 03 22:19:12.02: [23359]: RECV send MCF (message confirmation)
> Oct 03 22:19:12.02: [23359]: RECV FAX (00000082): from
> 0164258126, page
> 1 in 1:12, INF, 3.85 line/mm, 2-D MR, 4800 bit/s
> Oct 03 22:19:12.02: [23359]: <-- [7:AT+FDR\r]
> Oct 03 22:19:16.80: [23359]: --> [7:CONNECT]
> Oct 03 22:19:16.80: [23359]: RECV: begin page
> Oct 03 22:19:16.80: [23359]: RECV: send trigger 022
> Oct 03 22:19:16.80: [23359]: <-- data [1]
> Oct 03 22:20:11.53: [23359]: RECV: 32727 bytes of data, 860
> total lines
> Oct 03 22:20:19.59: [23359]: RECV: 4878 bytes of data, 1077
> total lines
> Oct 03 22:21:38.42: [23359]: CLOSE /dev/ttyS0
>
> ================================================================
> MOMDEM CONFIG
> ================================================================
> #
> # Generic Class 2.0 modem configuration.
> #
> # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
> #
> CountryCode: 31
> AreaCode: 164
> FAXNumber: "+31 xxx xxxxx"
> LongDistancePrefix: 0
> InternationalPrefix: 00
> DialStringRules: etc/dialrules
> ServerTracing: 1
> SessionTracing: 11
> RecvFileMode: 0600
> LogFileMode: 0600
> DeviceMode: 0600
> RingsBeforeAnswer: 1
> SpeakerVolume: off
> GettyArgs: "-h %l dx_%s"
> LocalIdentifier: MY NAME
> LogFacility: hylafax
> TagLineFont: etc/lutRS18.pcf
> TagLineFormat: "From %%l|%c|Page %%P of %%T"
> MaxRecvPages: 50
> #
> #
> # Modem-related stuff: should reflect modem command interface
> # and hardware connection/cabling (e.g. flow control).
> #
> ModemType: Class2.0 # use this to supply a hint
> #ModemRate: 19200 # max rate for DCE-DTE
> communication
> #ModemFlowControl: xonxoff # XON/XOFF flow
> control assumed
> #ModemSetupDTRCmd: AT&D2 # setup so DTR drop
> resets modem
> #ModemSetupDCDCmd: AT&C1 # setup so DCD
> reflects carrier
> (or not)
> #
> # We can append the "@" symbol to the dial string so that
> # the modem will wait 5 seconds before attempting to connect
> # and return result codes that distinguish between no carrier
> # and no answer. This makes it possible to avoid problems with
> # repeatedly dialing a number that doesn't have a fax machine
> # (kudos to Stuart Lynne for this trick.)
> #
> # NB: If you need to prefix phone numbers to get through a PBX,
> # put it in the ModemDialCmd; e.g. "DT9%s@".
> #
> #ModemDialCmd: ATDT%s # T for tone dialing
> #
> # Other possible configuration stuff. The default strings are
> # shown below. Only those that are different from the defaults
> # need to be included in the configuration file.
> #
> #ModemResetCmds: "" # stuff to do
> when modem
> is reset
> #ModemAnswerCmd: ATA # use this to answer
> phone
> #ModemNoFlowCmd: AT&K # disable flow control
> cmd
> #ModemHardFlowCmd: AT&K3 # hardware flow control cmd
> #ModemSoftFlowCmd: AT&K4 # software flow control cmd
> #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
> #
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
> # Note that we both turn the speaker on/off and set volume.
> #
> #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
> #ModemEchoOffCmd: ATE0 # disable command echo
> #ModemVerboseResultsCmd: ATV1 # enable
> verbose command
> results
> #ModemResultCodesCmd: ATQ0 # enable result codes
> #ModemOnHookCmd: ATH0 # place phone on hook
> (hangup)
> #ModemSoftResetCmd: ATZ # do soft reset of modem
> #ModemSoftResetCmdDelay: 3000 # pause after soft reset
> #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
> #ModemCommaPauseTimeCmd: ATS8=2 # comma pause
> time is 2
> seconds
> #ModemRecvFillOrder: LSB2MSB # bit order of received
> facsimile
> #ModemSendFillOrder: LSB2MSB # bit order modem expects for
> transmit
> #
> # Configuration parameters for Class 2.0 modems.
> #
> Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
> Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D
> (direct)
> Class2CQCmd: "" # commands to enable copy
> quality proc.
> Class2AbortCmd: AT+FKS # abort session command
> Class2CQQueryCmd: AT+FCQ=? # query for copy quality
> capabilities
> Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
> Class2TBCCmd: AT+FPP=0 # setup stream mode
> Class2CRCmd: AT+FCR=1 # enable capability to receive
> Class2PHCTOCmd: AT+FCT=30 # set phase C timeout
> parameter
> Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
> Class2LIDCmd: AT+FLI # set local identifier command
> Class2DCCCmd: AT+FCC # set modem
> capabilities command
> Class2DISCmd: AT+FIS # set session
> parameters command
> Class2DDISCmd: "" # disable pre-dial DIS command
> hack
> Class2CIGCmd: AT+FPI # set polling
> identifier command
> Class2NRCmd: AT+FNR=1,1,1,1 # setup status
> reporting command
> Class2PIECmd: AT+FIE=0 # disable interrupt-enable
> command
> Class2PTSCmd: AT+FPS # set post-page status command
> Class2PTSQueryCmd: AT+FPS? # set post-page status query
> command
> Class2SPLCmd: AT+FSP # set polling
> indicator command
> Class2NFLOCmd: AT+FLO=0 # set no flow control command
> Class2SFLOCmd: AT+FLO=1 # set software flow control
> command
> Class2HFLOCmd: AT+FLO=2 # set hardware flow control
> command
>
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
> _______________________
> To subscribe/unsubscribe, click
> http://lists.hylafax.org/cgi-bin/lsg2.cgi
> On UNIX: mail -s
> unsubscribe hylafax-users-request@hylafax.org < /dev/null
> *To learn about commercial HylaFAX(tm) support, mail
> sales@hylafax.org.*
>
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
*To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
- References:
- [hylafax-users] Zyxel
- From: Paul van Brouwershaven
- [hylafax-users] Zyxel
- Prev by Date: Re: [hylafax-users] Can Hylafax convert recorded fax sessions[wav] to image fomat of the original document ?
- Next by Date: Re: [hylafax-users] Can Hylafax convert recorded fax sessions[wav]to image fomat of the original document ?
- Previous by thread: [hylafax-users] Zyxel
- Next by thread: [hylafax-users] Can Hylafax convert recorded fax sessions[wav] to image fomat of the original document ?
- Index(es):
Project hosted by iFAX Solutions