 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] Zyxel
- To: <hylafax-users@hylafax.org>
- Subject: [hylafax-users] Zyxel
- From: "Paul van Brouwershaven" <paul@vanbrouwershaven.com>
- Date: Thu, 3 Oct 2002 22:40:30 +0200
Hi, When I try to send a fax to hylafax, the server discconect after receiving the first page ? Can someone help me with this problem ? Modem = Zyxel Omni 56K Class = 2.0 ================================================================ HYLAFAX TRANSFER LOG ================================================================ Oct 03 22:17:50.92: [23359]: SESSION BEGIN 00000082 31164262983 Oct 03 22:17:50.92: [23359]: HylaFAX (tm) Version 4.1.3 Oct 03 22:17:50.92: [23359]: <-- [4:ATA\r] Oct 03 22:18:00.66: [23359]: --> [4:+FCO] Oct 03 22:18:00.66: [23359]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyS0' Oct 03 22:18:00.66: [23359]: RECV FAX: begin Oct 03 22:18:00.94: [23359]: --> [27:+FTI:" 0164258126"] Oct 03 22:18:00.94: [23359]: REMOTE TSI "0164258126" Oct 03 22:18:00.94: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3] Oct 03 22:18:00.94: [23359]: REMOTE wants 4800 bit/s Oct 03 22:18:00.94: [23359]: REMOTE wants page width 1728 pixels in 215 mm Oct 03 22:18:00.94: [23359]: REMOTE wants unlimited page length Oct 03 22:18:00.94: [23359]: REMOTE wants 3.85 line/mm Oct 03 22:18:00.94: [23359]: REMOTE wants 2-D MR Oct 03 22:18:00.94: [23359]: --> [2:OK] Oct 03 22:18:00.94: [23359]: <-- [7:AT+FDR\r] Oct 03 22:18:06.07: [23359]: --> [20:+FCS:0,1,0,2,1,0,0,3] Oct 03 22:18:06.07: [23359]: REMOTE wants 4800 bit/s Oct 03 22:18:06.07: [23359]: REMOTE wants page width 1728 pixels in 215 mm Oct 03 22:18:06.07: [23359]: REMOTE wants unlimited page length Oct 03 22:18:06.07: [23359]: REMOTE wants 3.85 line/mm Oct 03 22:18:06.07: [23359]: REMOTE wants 2-D MR Oct 03 22:18:06.07: [23359]: --> [7:CONNECT] Oct 03 22:18:06.07: [23359]: RECV: begin page Oct 03 22:18:06.07: [23359]: RECV: send trigger 022 Oct 03 22:18:06.07: [23359]: <-- data [1] Oct 03 22:19:00.74: [23359]: RECV: 32736 bytes of data, 829 total lines Oct 03 22:19:10.58: [23359]: RECV: 5962 bytes of data, 1082 total lines Oct 03 22:19:11.99: [23359]: --> [16:+FPS:1,441,0,0,0] Oct 03 22:19:11.99: [23359]: --> [6:+FET:0] Oct 03 22:19:11.99: [23359]: RECV recv MPS (more pages, same document) Oct 03 22:19:11.99: [23359]: --> [2:OK] Oct 03 22:19:12.02: [23359]: RECV send MCF (message confirmation) Oct 03 22:19:12.02: [23359]: RECV FAX (00000082): from 0164258126, page 1 in 1:12, INF, 3.85 line/mm, 2-D MR, 4800 bit/s Oct 03 22:19:12.02: [23359]: <-- [7:AT+FDR\r] Oct 03 22:19:16.80: [23359]: --> [7:CONNECT] Oct 03 22:19:16.80: [23359]: RECV: begin page Oct 03 22:19:16.80: [23359]: RECV: send trigger 022 Oct 03 22:19:16.80: [23359]: <-- data [1] Oct 03 22:20:11.53: [23359]: RECV: 32727 bytes of data, 860 total lines Oct 03 22:20:19.59: [23359]: RECV: 4878 bytes of data, 1077 total lines Oct 03 22:21:38.42: [23359]: CLOSE /dev/ttyS0 ================================================================ MOMDEM CONFIG ================================================================ # # Generic Class 2.0 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 31 AreaCode: 164 FAXNumber: "+31 xxx xxxxx" LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules ServerTracing: 1 SessionTracing: 11 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 1 SpeakerVolume: off GettyArgs: "-h %l dx_%s" LocalIdentifier: MY NAME LogFacility: hylafax TagLineFont: etc/lutRS18.pcf TagLineFormat: "From %%l|%c|Page %%P of %%T" MaxRecvPages: 50 # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class2.0 # use this to supply a hint #ModemRate: 19200 # max rate for DCE-DTE communication #ModemFlowControl: xonxoff # XON/XOFF flow control assumed #ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem #ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not) # # We can append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s # T for tone dialing # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # #ModemResetCmds: "" # stuff to do when modem is reset #ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemSoftResetCmdDelay: 3000 # pause after soft reset #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # # Configuration parameters for Class 2.0 modems. # Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0 Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct) Class2CQCmd: "" # commands to enable copy quality proc. Class2AbortCmd: AT+FKS # abort session command Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities Class2TBCCmd: AT+FPP=0 # setup stream mode Class2CRCmd: AT+FCR=1 # enable capability to receive Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing Class2LIDCmd: AT+FLI # set local identifier command Class2DCCCmd: AT+FCC # set modem capabilities command Class2DISCmd: AT+FIS # set session parameters command Class2DDISCmd: "" # disable pre-dial DIS command hack Class2CIGCmd: AT+FPI # set polling identifier command Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command Class2PIECmd: AT+FIE=0 # disable interrupt-enable command Class2PTSCmd: AT+FPS # set post-page status command Class2PTSQueryCmd: AT+FPS? # set post-page status query command Class2SPLCmd: AT+FSP # set polling indicator command Class2NFLOCmd: AT+FLO=0 # set no flow control command Class2SFLOCmd: AT+FLO=1 # set software flow control command Class2HFLOCmd: AT+FLO=2 # set hardware flow control command ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*
- Follow-Ups:
- Re: [hylafax-users] Zyxel
- From: Paul van Brouwershaven
- Re: [hylafax-users] Zyxel
- Prev by Date: [hylafax-users] Zyxel
- Next by Date: [hylafax-users] Can Hylafax convert recorded fax sessions[wav] to image fomat of the original document ?
- Previous by thread: [hylafax-users] Zyxel
- Next by thread: Re: [hylafax-users] Zyxel
- Index(es):
Project hosted by iFAX Solutions