HylaFAX The world's most advanced open source fax server
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]

[hylafax-users] Hylafax4.1.3+DIGI Acceleport RAS8 => receiving 0 lines ?!

Hi,

I installed Hylafax 4.1.3 on Redhat 7.3 with a Digi
Acceleport RAS8 card. Receiving from some (older?)
faxmachines works fine, but from others I receive 0
lines without reporting any errors (see session
logs+config) ? I already tried to change flow control
and even class1, wihout success.

Any help or working config is really appreciated !

Thanks,

Klussie 

BAD SESSION
===========
Aug 07 17:42:45.72: [ 1128]: SESSION BEGIN 00000018
3237221982
Aug 07 17:42:45.72: [ 1128]: HylaFAX (tm) Version
4.1.3
Aug 07 17:42:45.72: [ 1128]: <-- [4:ATA\r]
Aug 07 17:42:52.38: [ 1128]: --> [4:+FCO]
Aug 07 17:42:52.38: [ 1128]: ANSWER: FAX CONNECTION 
DEVICE '/dev/ttyG000'
Aug 07 17:42:52.38: [ 1128]: RECV FAX: begin
Aug 07 17:42:54.29: [ 1128]: --> [27:+FTI:"        XXX
XX XX XX"]
Aug 07 17:42:54.29: [ 1128]: REMOTE TSI "XXX XX XX XX"
Aug 07 17:42:54.29: [ 1128]: -->
[20:+FCS:0,5,0,2,3,1,0,0]
Aug 07 17:42:54.29: [ 1128]: REMOTE wants 14400 bit/s
Aug 07 17:42:54.29: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:42:54.29: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:42:54.29: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:42:54.29: [ 1128]: REMOTE wants 2-D MMR
Aug 07 17:42:54.29: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:42:54.29: [ 1128]: --> [2:OK]
Aug 07 17:42:54.29: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:42:59.53: [ 1128]: -->
[20:+FCS:0,5,0,2,3,1,0,0]
Aug 07 17:42:59.53: [ 1128]: REMOTE wants 14400 bit/s
Aug 07 17:42:59.53: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:42:59.53: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:42:59.53: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:42:59.53: [ 1128]: REMOTE wants 2-D MMR
Aug 07 17:42:59.53: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:42:59.53: [ 1128]: --> [7:CONNECT]
Aug 07 17:42:59.53: [ 1128]: RECV: begin page
Aug 07 17:42:59.57: [ 1128]: RECV: send trigger 022
Aug 07 17:42:59.57: [ 1128]: <-- data [1]
Aug 07 17:43:07.24: [ 1128]: RECV: 0 total lines, 0
bad lines, 0 consecutive bad lines
Aug 07 17:43:07.26: [ 1128]: -->
[17:+FPS:1,1144,0,0,0]
Aug 07 17:43:07.26: [ 1128]: --> [6:+FET:0]
Aug 07 17:43:07.26: [ 1128]: RECV recv MPS (more
pages, same document)
Aug 07 17:43:07.26: [ 1128]: --> [2:OK]
Aug 07 17:43:07.26: [ 1128]: RECV send MCF (message
confirmation)
Aug 07 17:43:07.26: [ 1128]: RECV FAX (00000018): from
XXX XX XX XX, page 1 in 0:13, INF, 3.85 line/mm, 2-D
MMR, 14400 bit/s
Aug 07 17:43:07.26: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:43:09.38: [ 1128]: -->
[20:+FCS:0,5,0,2,3,1,0,0]
Aug 07 17:43:09.38: [ 1128]: REMOTE wants 14400 bit/s
Aug 07 17:43:09.38: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:43:09.38: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:43:09.38: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:43:09.38: [ 1128]: REMOTE wants 2-D MMR
Aug 07 17:43:09.38: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:43:09.38: [ 1128]: --> [7:CONNECT]
Aug 07 17:43:09.38: [ 1128]: RECV: begin page
Aug 07 17:43:09.40: [ 1128]: RECV: send trigger 022
Aug 07 17:43:09.40: [ 1128]: <-- data [1]
Aug 07 17:43:15.63: [ 1128]: RECV: 0 total lines, 0
bad lines, 0 consecutive bad lines
Aug 07 17:43:15.65: [ 1128]: -->
[17:+FPS:1,1145,0,0,0]
Aug 07 17:43:15.65: [ 1128]: --> [6:+FET:2]
Aug 07 17:43:15.65: [ 1128]: RECV recv EOP (no more
pages or documents)
Aug 07 17:43:15.65: [ 1128]: --> [2:OK]
Aug 07 17:43:15.65: [ 1128]: RECV send MCF (message
confirmation)
Aug 07 17:43:15.65: [ 1128]: RECV FAX (00000018): from
XXX XX XX XX, page 2 in 0:08, INF, 3.85 line/mm, 2-D
MMR, 14400 bit/s
Aug 07 17:43:15.65: [ 1128]: RECV FAX (00000018):
recvq/fax00009.tif from XXX XX XX XX, route to
<unspecified>, 2 pages in 0:23
Aug 07 17:43:15.66: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:43:18.83: [ 1128]: --> [7:+FHS:00]
Aug 07 17:43:18.83: [ 1128]: REMOTE HANGUP: Normal and
proper end of connection (code 0)
Aug 07 17:43:18.83: [ 1128]: RECV FAX: bin/faxrcvd
"recvq/fax00009.tif" "ttyG000" "00000018" "" "" ""
Aug 07 17:43:19.70: [ 1128]: RECV FAX: end
Aug 07 17:43:19.70: [ 1128]: SESSION END

GOOD SESSION
============
Aug 07 17:38:19.25: [ 1128]: SESSION BEGIN 00000017
3237221982
Aug 07 17:38:19.25: [ 1128]: HylaFAX (tm) Version
4.1.3
Aug 07 17:38:19.25: [ 1128]: <-- [4:ATA\r]
Aug 07 17:38:25.85: [ 1128]: --> [4:+FCO]
Aug 07 17:38:25.85: [ 1128]: ANSWER: FAX CONNECTION 
DEVICE '/dev/ttyG000'
Aug 07 17:38:25.85: [ 1128]: RECV FAX: begin
Aug 07 17:38:27.76: [ 1128]: --> [27:+FTI:"        XX
XX XXXXXX"]
Aug 07 17:38:27.76: [ 1128]: REMOTE TSI "XX XX XXXXXX"
Aug 07 17:38:27.76: [ 1128]: -->
[20:+FCS:0,3,0,2,1,1,0,0]
Aug 07 17:38:27.76: [ 1128]: REMOTE wants 9600 bit/s
Aug 07 17:38:27.76: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:38:27.76: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:38:27.76: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:38:27.76: [ 1128]: REMOTE wants 2-D MR
Aug 07 17:38:27.76: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:38:27.76: [ 1128]: --> [2:OK]
Aug 07 17:38:27.76: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:38:31.48: [ 1128]: -->
[20:+FCS:0,3,0,2,1,1,0,0]
Aug 07 17:38:31.48: [ 1128]: REMOTE wants 9600 bit/s
Aug 07 17:38:31.48: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:38:31.48: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:38:31.48: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:38:31.48: [ 1128]: REMOTE wants 2-D MR
Aug 07 17:38:31.48: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:38:31.48: [ 1128]: --> [7:CONNECT]
Aug 07 17:38:31.48: [ 1128]: RECV: begin page
Aug 07 17:38:31.50: [ 1128]: RECV: send trigger 022
Aug 07 17:38:31.50: [ 1128]: <-- data [1]
Aug 07 17:38:56.91: [ 1128]: RECV: 25940 bytes of
data, 1121 total lines
Aug 07 17:38:56.93: [ 1128]: -->
[17:+FPS:1,1121,0,0,0]
Aug 07 17:38:56.93: [ 1128]: --> [6:+FET:0]
Aug 07 17:38:56.93: [ 1128]: RECV recv MPS (more
pages, same document)
Aug 07 17:38:56.93: [ 1128]: --> [2:OK]
Aug 07 17:38:56.93: [ 1128]: RECV send MCF (message
confirmation)
Aug 07 17:38:56.93: [ 1128]: RECV FAX (00000017): from
XX XX XXXXXX, page 1 in 0:29, INF, 3.85 line/mm, 2-D
MR, 9600 bit/s
Aug 07 17:38:56.93: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:38:59.11: [ 1128]: -->
[20:+FCS:0,3,0,2,1,1,0,0]
Aug 07 17:38:59.11: [ 1128]: REMOTE wants 9600 bit/s
Aug 07 17:38:59.11: [ 1128]: REMOTE wants page width
1728 pixels in 215 mm
Aug 07 17:38:59.11: [ 1128]: REMOTE wants unlimited
page length 
Aug 07 17:38:59.11: [ 1128]: REMOTE wants 3.85 line/mm
Aug 07 17:38:59.11: [ 1128]: REMOTE wants 2-D MR
Aug 07 17:38:59.11: [ 1128]: REMOTE wants T.30 Annex
A, ECM
Aug 07 17:38:59.11: [ 1128]: --> [7:CONNECT]
Aug 07 17:38:59.11: [ 1128]: RECV: begin page
Aug 07 17:38:59.13: [ 1128]: RECV: send trigger 022
Aug 07 17:38:59.13: [ 1128]: <-- data [1]
Aug 07 17:39:26.11: [ 1128]: RECV: 27501 bytes of
data, 1125 total lines
Aug 07 17:39:26.13: [ 1128]: -->
[17:+FPS:1,1125,0,0,0]
Aug 07 17:39:26.13: [ 1128]: --> [6:+FET:2]
Aug 07 17:39:26.13: [ 1128]: RECV recv EOP (no more
pages or documents)
Aug 07 17:39:26.13: [ 1128]: --> [2:OK]
Aug 07 17:39:26.13: [ 1128]: RECV send MCF (message
confirmation)
Aug 07 17:39:26.13: [ 1128]: RECV FAX (00000017): from
XX XX XXXXXX, page 2 in 0:30, INF, 3.85 line/mm, 2-D
MR, 9600 bit/s
Aug 07 17:39:26.13: [ 1128]: RECV FAX (00000017):
recvq/fax00008.tif from XX XX XXXXXX, route to
<unspecified>, 2 pages in 1:01
Aug 07 17:39:26.15: [ 1128]: <-- [7:AT+FDR\r]
Aug 07 17:39:29.27: [ 1128]: --> [7:+FHS:00]
Aug 07 17:39:29.27: [ 1128]: REMOTE HANGUP: Normal and
proper end of connection (code 0)
Aug 07 17:39:29.27: [ 1128]: RECV FAX: bin/faxrcvd
"recvq/fax00008.tif" "ttyG000" "00000017" "" "" ""
Aug 07 17:39:31.68: [ 1128]: RECV FAX: end
Aug 07 17:39:31.68: [ 1128]: SESSION END

config file
===========
#
# Generic Class 2.0 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		XX
AreaCode:		X
FAXNumber:		+XX.X.XXX.XX.XX
LongDistancePrefix:	0
InternationalPrefix:	00
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		""
LocalIdentifier:	XXXXXXXXX
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%P of %%T"
MaxRecvPages:		25
#
#
# Modem-related stuff: should reflect modem command
interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2.0	# use this to supply a hint
#ModemRate:		19200		# max rate for DCE-DTE
communication
#ModemFlowControl:	RTSCTS		# XON/XOFF flow control
assumed
#ModemSetupDTRCmd:	AT&D2		# setup so DTR drop resets
modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects
carrier (or not)
#
# We can append the "@" symbol to the dial string so
that
# the modem will wait 5 seconds before attempting to
connect
# and return result codes that distinguish between no
carrier
# and no answer.  This makes it possible to avoid
problems with
# repeatedly dialing a number that doesn't have a fax
machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get
through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s		# T for tone dialing
#
# Other possible configuration stuff.  The default
strings are
# shown below.  Only those that are different from the
defaults
# need to be included in the configuration file.
#
#ModemResetCmds:		""		# stuff to do when modem is
reset
#ModemAnswerCmd:		ATA		# use this to answer phone
#ModemNoFlowCmd:		AT&K		# disable flow control cmd
#ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
#ModemSoftFlowCmd:	AT&K4		# software flow control cmd
#ModemNoAutoAnswerCmd:	ATS0=0		# disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW
MEDIUM HIGH.
# Note that we both turn the speaker on/off and set
volume.
#
#ModemSetVolumeCmd:	"ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd:	ATE0		# disable command echo
#ModemVerboseResultsCmd:	ATV1		# enable verbose
command results
#ModemResultCodesCmd:	ATQ0		# enable result codes
#ModemOnHookCmd:		ATH0		# place phone on hook (hangup)
#ModemSoftResetCmd:	ATZ		# do soft reset of modem
#ModemSoftResetCmdDelay:	3000	# pause after soft reset
#ModemWaitTimeCmd:	ATS7=60		# wait 60 seconds for
carrier
#ModemCommaPauseTimeCmd:	ATS8=2		# comma pause time is
2 seconds
#ModemRecvFillOrder:	LSB2MSB		# bit order of received
facsimile
#ModemSendFillOrder:	LSB2MSB		# bit order modem
expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:		AT+FCLASS=2.0	# command to enter class 2.0
Class2BORCmd:		AT+FBO=0	# bit order for phase B/C/D
(direct)
Class2CQCmd:		""		# commands to enable copy quality
proc.
Class2AbortCmd:		AT+FKS		# abort session command
Class2CQQueryCmd:	AT+FCQ=?	# query for copy quality
capabilities
Class2DCCQueryCmd:	AT+FCC=?	# query for modem
capabilities
Class2TBCCmd:		AT+FPP=0	# setup stream mode
Class2CRCmd:		AT+FCR=1	# enable capability to receive
Class2PHCTOCmd:		AT+FCT=30	# set phase C timeout
parameter
Class2BUGCmd:		AT+FBU=1	# enable HDLC frame tracing
Class2LIDCmd:		AT+FLI		# set local identifier command
Class2DCCCmd:		AT+FCC		# set modem capabilities
command
Class2DISCmd:		AT+FIS		# set session parameters
command
Class2DDISCmd:		""		# disable pre-dial DIS command
hack
Class2CIGCmd:		AT+FPI		# set polling identifier
command
Class2NRCmd:		AT+FNR=1,1,1,1	# setup status reporting
command
Class2PIECmd:		AT+FIE=0	# disable interrupt-enable
command
Class2PTSCmd:		AT+FPS		# set post-page status command
Class2PTSQueryCmd:	AT+FPS?		# set post-page status
query command
Class2SPLCmd:		AT+FSP		# set polling indicator command
Class2NFLOCmd:		AT+FLO=0	# set no flow control command
Class2SFLOCmd:		AT+FLO=1	# set software flow control
command
Class2HFLOCmd:		AT+FLO=2	# set hardware flow control
command




__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com

____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
  *To learn about commercial HylaFAX(tm) support, mail sales@hylafax.org.*

Project hosted by iFAX Solutions