[hylafax-users] Class2DDISCmd

[Joachim Zobel <nc-zobeljo@netcologne.de>]

Hi.

I have now found the time to check on a problem my hylafax server (linux) 
has with several faxes.

It looks like my hylafax sends an FDIS after dialing. I wonder why this 
happens, because i have configured
Class2DDISCmd:          AT+FDIS
which as I have understood it should prevent this. Hylafax has identified 
my no name modem (according to its config.tty) as
Yocom 1414E     firmware E.C.  Version : 7.1

My hylafax version is (according to faxsetup) HylaFAX (tm) v4.0pl2.

Any ideas appreciated.
Thanx,
Joachim

May 02 20:14:24.88: [ 2869]: SESSION BEGIN 00000036 49221683351
May 02 20:14:24.88: [ 2869]: SEND FAX: JOB 15 DEST 0221683351 COMMID 00000036
May 02 20:14:24.88: [ 2869]: MODEM set DTR OFF
May 02 20:14:24.88: [ 2869]: DELAY 2600 ms
May 02 20:14:27.48: [ 2869]: MODEM set DTR ON
May 02 20:14:27.48: [ 2869]: MODEM set baud rate: 19200 baud, input flow 
XON/XOFF, output flow XON/XOFF
May 02 20:14:27.48: [ 2869]: MODEM flush i/o
May 02 20:14:27.48: [ 2869]: <-- [15:ATE0V1Q0S0=0H0\r]
May 02 20:14:28.08: [ 2869]: --> [2:OK]
May 02 20:14:28.08: [ 2869]: <-- [30:ATS8=2S7=60&S1\G0\Q4\X1&D2&C1\r]
May 02 20:14:28.33: [ 2869]: --> [2:OK]
May 02 20:14:28.33: [ 2869]: <-- [12:AT+FCLASS=2\r]
May 02 20:14:28.57: [ 2869]: --> [2:OK]
May 02 20:14:28.57: [ 2869]: <-- [10:AT+FTBC=0\r]
May 02 20:14:28.81: [ 2869]: --> [5:ERROR]
May 02 20:14:28.81: [ 2869]: MODEM Command error
May 02 20:14:28.81: [ 2869]: <-- [10:AT+FBOR=0\r]
May 02 20:14:29.04: [ 2869]: --> [2:OK]
May 02 20:14:29.04: [ 2869]: <-- [13:AT+FPHCTO=30\r]
May 02 20:14:29.28: [ 2869]: --> [5:ERROR]
May 02 20:14:29.28: [ 2869]: MODEM Command error
May 02 20:14:29.28: [ 2869]: <-- [10:AT+FBUG=1\r]
May 02 20:14:29.51: [ 2869]: --> [2:OK]
May 02 20:14:29.51: [ 2869]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
May 02 20:14:29.75: [ 2869]: --> [2:OK]
May 02 20:14:29.75: [ 2869]: <-- [7:ATL1M1\r]
May 02 20:14:29.98: [ 2869]: --> [2:OK]
May 02 20:14:29.98: [ 2869]: STATE CHANGE: RUNNING -> SENDING
May 02 20:14:29.98: [ 2869]: MODEM input buffering enabled
May 02 20:14:29.98: [ 2869]: <-- [12:AT+FCLASS=2\r]
May 02 20:14:30.31: [ 2869]: --> [2:OK]
May 02 20:14:30.31: [ 2869]: <-- [10:AT+FTBC=0\r]
May 02 20:14:30.65: [ 2869]: --> [5:ERROR]
May 02 20:14:30.65: [ 2869]: MODEM Command error
May 02 20:14:30.65: [ 2869]: <-- [10:AT+FBOR=0\r]
May 02 20:14:30.98: [ 2869]: --> [2:OK]
May 02 20:14:30.98: [ 2869]: <-- [13:AT+FPHCTO=30\r]
May 02 20:14:31.32: [ 2869]: --> [5:ERROR]
May 02 20:14:31.32: [ 2869]: MODEM Command error
May 02 20:14:31.32: [ 2869]: <-- [10:AT+FBUG=1\r]
May 02 20:14:31.65: [ 2869]: --> [2:OK]
May 02 20:14:31.65: [ 2869]: <-- [24:AT+FDCC=1,5,2,2,2,0,0,0\r]
May 02 20:14:31.99: [ 2869]: --> [2:OK]
May 02 20:14:31.99: [ 2869]: <-- [23:AT+FLID="NothingSetup"\r]
May 02 20:14:32.33: [ 2869]: --> [2:OK]
May 02 20:14:32.33: [ 2869]: <-- [24:AT+FDIS=0,5,0,2,0,0,0,0\r]
May 02 20:14:32.67: [ 2869]: --> [2:OK]
May 02 20:14:32.67: [ 2869]: DIAL 0221683351
May 02 20:14:32.67: [ 2869]: <-- [15:ATDT0221683351\r]
May 02 20:14:47.74: [ 2869]: --> [3:CED]
May 02 20:14:52.33: [ 2869]: --> [6:+FHR: ]
May 02 20:14:52.68: [ 2869]: --> [6:+FHR: ]
May 02 20:14:52.68: [ 2869]: --> [5:+FCON]
May 02 20:14:52.68: [ 2869]: --> [29:+FCSI: "                    "]
May 02 20:14:52.68: [ 2869]: REMOTE CSI ""
May 02 20:14:52.68: [ 2869]: --> [22:+FDIS: 1,3,0,2,0,0,0,4]
May 02 20:14:52.68: [ 2869]: --> [2:OK]
May 02 20:14:52.68: [ 2869]: REMOTE best rate 9600 bit/s
May 02 20:14:52.68: [ 2869]: REMOTE max page width 1728 pixels in 215 mm
May 02 20:14:52.68: [ 2869]: REMOTE max unlimited page length
May 02 20:14:52.68: [ 2869]: REMOTE best vres 7.7 line/mm
May 02 20:14:52.68: [ 2869]: REMOTE best format 1-D MR
May 02 20:14:52.68: [ 2869]: REMOTE best 20 ms, 10 ms/scanline
May 02 20:14:52.68: [ 2869]: USE 9600 bit/s
May 02 20:14:52.68: [ 2869]: USE 20 ms, 10 ms/scanline
May 02 20:14:52.68: [ 2869]: SEND file "docq/doc17.ps;00"
May 02 20:14:52.68: [ 2869]: USE page width 1728 pixels in 215 mm
May 02 20:14:52.68: [ 2869]: USE unlimited page length
May 02 20:14:52.68: [ 2869]: USE 3.85 line/mm
May 02 20:14:52.68: [ 2869]: USE 1-D MR
May 02 20:14:52.68: [ 2869]: <-- [24:AT+FDIS=0,3,0,2,0,0,0,4\r]
May 02 20:14:54.04: [ 2869]: --> [15:+FHT: FF 13 FB ]
May 02 20:14:54.04: [ 2869]: --> [9:+FHNG: 40]
May 02 20:14:54.04: [ 2869]: REMOTE HANGUP: Unspecified Transmit Phase C 
error (code 40)
May 02 20:14:54.04: [ 2869]: --> [2:OK]
May 02 20:14:54.04: [ 2869]: MODEM set XON/XOFF/NOW: input ignored, output 
generated
May 02 20:14:54.04: [ 2869]: <-- [7:AT+FDT\r]
May 02 20:14:54.47: [ 2869]: --> [10:NO CARRIER]
May 02 20:14:54.47: [ 2869]: MODEM No carrier
May 02 20:14:54.47: [ 2869]: MODEM set XON/XOFF/NOW: input interpreted, 
output generated
May 02 20:14:54.47: [ 2869]: <-- [5:ATH0\r]
May 02 20:14:55.17: [ 2869]: --> [2:OK]
May 02 20:14:55.17: [ 2869]: MODEM set DTR OFF
May 02 20:14:55.17: [ 2869]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
May 02 20:14:55.17: [ 2869]: SESSION END
--
"... ein Geschlecht erfinderischer Zwerge, die fuer alles gemietet werden
koennen."                            - Bertolt Brecht - Leben des Galilei


____________________ HylaFAX(tm) Users Mailing List _______________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
 On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null