 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
[hylafax-users] problem after upgrade to 4.1.2
- To: hylafax-users@hylafax.org
- Subject: [hylafax-users] problem after upgrade to 4.1.2
- From: Purwanto <purwanto@makro.co.id>
- Date: Tue, 2 Jul 2002 07:49:18 +0700 (JAVT)
Hi all..
I just upgrade hylafax to ver 4.1.2, after that i could not sent any fax
from windows or from local server.
Modem like do handsake, ant then stop, i use AT&T dataport express modem.
here a log file :
---- Transcript of session follows ----
Jul 01 16:37:30.52: [16767]: SESSION BEGIN 00000085 62217306
Jul 01 16:37:30.52: [16767]: HylaFAX (tm) Version 4.1.2
Jul 01 16:37:30.52: [16767]: SEND FAX: JOB 29 DEST 7306 COMMID 00000085
DEVICE '/dev/ttyS1'
Jul 01 16:37:30.52: [16767]: MODEM set DTR OFF
Jul 01 16:37:30.52: [16767]: DELAY 75 ms
Jul 01 16:37:30.60: [16767]: MODEM set DTR ON
Jul 01 16:37:30.60: [16767]: DELAY 2600 ms
Jul 01 16:37:33.20: [16767]: MODEM set baud rate: 19200 baud, input
flow RTS/CTS, output flow RTS/CTS
Jul 01 16:37:33.20: [16767]: MODEM flush i/o
Jul 01 16:37:33.20: [16767]: <-- [4:ATZ\r]
Jul 01 16:37:34.02: [16767]: --> [2:OK]
Jul 01 16:37:34.02: [16767]: DELAY 3000 ms
Jul 01 16:37:37.02: [16767]: <-- [5:ATE0\r]
Jul 01 16:37:37.14: [16767]: --> [4:ATE0]
Jul 01 16:37:37.14: [16767]: --> [2:OK]
Jul 01 16:37:37.14: [16767]: <-- [5:ATV1\r]
Jul 01 16:37:37.26: [16767]: --> [2:OK]
Jul 01 16:37:37.26: [16767]: <-- [5:ATQ0\r]
Jul 01 16:37:37.38: [16767]: --> [2:OK]
Jul 01 16:37:37.38: [16767]: <-- [7:ATS0=0\r]
Jul 01 16:37:37.50: [16767]: --> [2:OK]
Jul 01 16:37:37.50: [16767]: <-- [7:ATS8=2\r]
Jul 01 16:37:37.62: [16767]: --> [2:OK]
Jul 01 16:37:37.62: [16767]: <-- [8:ATS7=60\r]
Jul 01 16:37:37.74: [16767]: --> [2:OK]
Jul 01 16:37:37.74: [16767]: <-- [12:AT&R0\D1\Q3\r]
Jul 01 16:37:37.86: [16767]: --> [2:OK]
Jul 01 16:37:37.86: [16767]: <-- [6:AT&D2\r]
Jul 01 16:37:37.98: [16767]: --> [2:OK]
Jul 01 16:37:37.98: [16767]: <-- [6:AT&C1\r]
Jul 01 16:37:38.10: [16767]: --> [2:OK]
Jul 01 16:37:38.10: [16767]: <-- [12:AT+FCLASS=1\r]
Jul 01 16:37:38.22: [16767]: --> [2:OK]
Jul 01 16:37:38.22: [16767]: <-- [9:AT+FAA=0\r]
Jul 01 16:37:38.34: [16767]: --> [2:OK]
Jul 01 16:37:38.34: [16767]: <-- [7:ATL0M1\r]
Jul 01 16:37:38.46: [16767]: --> [2:OK]
Jul 01 16:37:38.46: [16767]: MODEM input buffering enabled
Jul 01 16:37:38.46: [16767]: <-- [12:AT+FCLASS=1\r]
Jul 01 16:37:38.68: [16767]: --> [2:OK]
Jul 01 16:37:38.68: [16767]: DIAL 7306
Jul 01 16:37:38.68: [16767]: <-- [9:ATDT7306\r]
Jul 01 16:37:55.72: [16767]: --> [7:CONNECT]
Jul 01 16:37:55.72: [16767]: MODEM input buffering disabled
Jul 01 16:37:58.44: [16767]: --> HDLC<39:FF C0 04 00 00 8C 00 72 1D 00 21
B0 BB 00 00 BB BB 00 00 BB BB BB BB BB 40 E0 80 80 68 44 08 B7 44 09 00 00
08 20 34>
Jul 01 16:37:58.44: [16767]: --> [2:OK]
Jul 01 16:37:58.44: [16767]: REMOTE NSF "00 00 31 00 4E B8 00 84 0D DD 00
00 DD DD 00 00 DD DD DD DD DD 02 07 01 01 16 22 10 ED 22 90 00 00 10 04 2C
00"
Jul 01 16:37:58.44: [16767]: NSF remote fax equipment: Sharp/Olivetti
Jul 01 16:37:58.44: [16767]: <-- [9:AT+FRH=3\r]
Jul 01 16:37:58.45: [16767]: --> [7:CONNECT]
Jul 01 16:37:58.47: [16767]: --> HDLC<25:FF C0 02 4C 1C 0C 2C 8C 6C 2C 04
8C 4C 0C 04 04 04 04 04 04 04 04 04 AC 28>
Jul 01 16:37:58.47: [16767]: --> [2:OK]
Jul 01 16:37:58.47: [16767]: REMOTE CSI "021 4614082"
Jul 01 16:37:58.47: [16767]: <-- [9:AT+FRH=3\r]
Jul 01 16:37:58.48: [16767]: --> [7:CONNECT]
Jul 01 16:37:58.49: [16767]: --> HDLC<9:FF C8 01 00 72 1D 00 71 24>
Jul 01 16:37:58.49: [16767]: --> [2:OK]
Jul 01 16:37:58.49: [16767]: REMOTE best rate 9600 bit/s
Jul 01 16:37:58.49: [16767]: REMOTE max page width 1728 pixels in 215 mm
Jul 01 16:37:58.49: [16767]: REMOTE max unlimited page length
Jul 01 16:37:58.49: [16767]: REMOTE best vres 7.7 line/mm
Jul 01 16:37:58.49: [16767]: REMOTE best format 1-D MR
Jul 01 16:37:58.49: [16767]: REMOTE best 20 ms, 10 ms/scanline
Jul 01 16:37:58.49: [16767]: USE 9600 bit/s
Jul 01 16:37:58.49: [16767]: USE 20 ms, 10 ms/scanline
Jul 01 16:37:58.49: [16767]: SEND file "docq/doc28.ps;01"
Jul 01 16:37:58.49: [16767]: USE page width 1728 pixels in 215 mm
Jul 01 16:37:58.49: [16767]: USE unlimited page length
Jul 01 16:37:58.49: [16767]: USE 7.7 line/mm
Jul 01 16:37:58.49: [16767]: USE 1-D MR
Jul 01 16:37:58.49: [16767]: SEND training at v.29 9600 bit/s
Jul 01 16:37:58.49: [16767]: <-- [9:AT+FTH=3\r]
Jul 01 16:37:58.51: [16767]: --> [7:CONNECT]
Jul 01 16:37:58.51: [16767]: <-- HDLC<23:FF C0 C2 AC EC 0C 2C 0C 2C 1C 8C
4C 4C 6C D4 04 04 04 04 04 04 04 04>
Jul 01 16:38:00.21: [16767]: --> [7:CONNECT]
Jul 01 16:38:00.21: [16767]: <-- HDLC<6:FF C8 C1 00 62 10>
Jul 01 16:38:00.53: [16767]: --> [2:OK]
Jul 01 16:38:00.53: [16767]: <-- [9:AT+FTS=7\r]
Jul 01 16:38:00.61: [16767]: --> [2:OK]
Jul 01 16:38:00.61: [16767]: <-- [10:AT+FTM=96\r]
Jul 01 16:38:00.74: [16767]: -->
[41:3,24,48,72,73,74,96,97,98,121,122,145,146]
Jul 01 16:38:00.74: [16767]: --> [5:ERROR]
Jul 01 16:38:00.74: [16767]: MODEM Command error
Jul 01 16:38:00.74: [16767]: Problem sending TCF data
Jul 01 16:38:00.74: [16767]: <-- [9:AT+FRH=3\r]
Jul 01 16:38:00.86: [16767]: --> [5:ERROR]
Jul 01 16:38:00.86: [16767]: MODEM Command error
Jul 01 16:38:00.86: [16767]: DELAY 1500 ms
Jul 01 16:38:02.36: [16767]: SEND training at v.29 7200 bit/s
Jul 01 16:38:02.36: [16767]: <-- [9:AT+FTH=3\r]
Jul 01 16:38:02.48: [16767]: --> [5:ERROR]
Jul 01 16:38:02.48: [16767]: Error sending T.30 prologue frames
Jul 01 16:38:02.48: [16767]: SEND training at v.27ter 4800 bit/s
Jul 01 16:38:02.48: [16767]: <-- [9:AT+FTH=3\r]
Jul 01 16:38:02.60: [16767]: --> [5:ERROR]
Jul 01 16:38:02.60: [16767]: Error sending T.30 prologue frames
Jul 01 16:38:02.60: [16767]: SEND training at v.27ter fallback mode 2400
bit/s
Jul 01 16:38:02.60: [16767]: <-- [9:AT+FTH=3\r]
Jul 01 16:38:02.72: [16767]: --> [5:ERROR]
Jul 01 16:38:02.72: [16767]: Error sending T.30 prologue frames
Jul 01 16:38:02.72: [16767]: TRAINING failed
Jul 01 16:38:02.72: [16767]: <-- [9:AT+FTH=3\r]
Jul 01 16:38:02.84: [16767]: --> [5:ERROR]
Jul 01 16:38:02.84: [16767]: MODEM input buffering enabled
Jul 01 16:38:02.84: [16767]: <-- [5:ATH0\r]
Jul 01 16:38:03.76: [16767]: --> [2:OK]
Jul 01 16:38:03.76: [16767]: MODEM set DTR OFF
Jul 01 16:38:03.76: [16767]: SESSION END
regards
Purwanto
____________________ HylaFAX(tm) Users Mailing List _______________________
To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- Follow-Ups:
- Re: [hylafax-users] problem after upgrade to 4.1.2
- From: Lee Howard
- Re: [hylafax-users] problem after upgrade to 4.1.2
- Prev by Date: Re: [hylafax-users] modem is wedged?
- Next by Date: Re: [hylafax-users] Small typeface faxing from filepro
- Previous by thread: Re: [hylafax-users] modem is wedged?
- Next by thread: Re: [hylafax-users] problem after upgrade to 4.1.2
- Index(es):
Project hosted by iFAX Solutions