 HylaFAX The world's
most advanced open source fax server
|
[Date Prev][Date Next][Thread Prev][Thread Next] [Date Index] [Thread Index]
Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- To: hylafax-users@hylafax.org
- Subject: Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Paul van der Vlis <paul@vandervlis.nl>
- Date: Thu, 18 Apr 2002 18:10:06 +0200
Lee Howard wrote: > On 2002.04.18 03:21 Paul van der Vlis wrote: > >> I did run "faxaddmodem" on the Zyxel to let it use class 1, but after >> that it does not answer the phone anymore (modem is ringing, faxgetty >> does not answer). When I take a look at the configuration file, it's a >> "generic class 1 modem configuration file". > > > Set ServerTracing to 0xFFF and send the relevant parts of the system log > showing faxgetty. > > Send also the "configuration file" and the output of probemodem <device>. > > Lee. Hello! This is the log (the isdn-messages other then from "faxgetty" are coming from another ISDN adapter). Thanks for your support! with regards, Paul van der Vlis. ------ Apr 18 17:22:46 server -- MARK -- Apr 18 17:31:03 server FaxGetty[28077]: CAUGHT SIGNAL 15 Apr 18 17:31:03 server FaxGetty[28077]: CLOSE /dev/ttyS0 Apr 18 17:31:03 server FaxGetty[29002]: OPEN /dev/ttyS0 Apr 18 17:31:03 server FaxGetty[29002]: Purge stale UUCP lock /var/lock/LCK..ttyS0 Apr 18 17:31:03 server FaxGetty[29002]: MODEM set DTR OFF Apr 18 17:31:03 server FaxGetty[29002]: DELAY 75 ms Apr 18 17:31:03 server FaxGetty[29002]: MODEM set DTR ON Apr 18 17:31:03 server FaxGetty[29002]: DELAY 2600 ms Apr 18 17:31:06 server FaxGetty[29002]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF Apr 18 17:31:06 server FaxGetty[29002]: MODEM flush i/o Apr 18 17:31:06 server FaxGetty[29002]: <-- [4:ATZ\r] Apr 18 17:31:36 server FaxGetty[29002]: MODEM TIMEOUT: reading line from modem Apr 18 17:31:36 server FaxGetty[29002]: MODEM <Timeout> Apr 18 17:31:36 server FaxGetty[29002]: MODEM set DTR OFF Apr 18 17:31:36 server FaxGetty[29002]: DELAY 75 ms Apr 18 17:31:36 server FaxGetty[29002]: MODEM set DTR ON Apr 18 17:31:36 server FaxGetty[29002]: DELAY 2600 ms Apr 18 17:31:39 server FaxGetty[29002]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF Apr 18 17:31:39 server FaxGetty[29002]: MODEM flush i/o Apr 18 17:31:39 server FaxGetty[29002]: <-- [4:ATZ\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [4:PUA��] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [5:ATE0\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [4:ATE0] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [5:ATV1\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [5:ATQ0\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [7:ATS0=0\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [7:ATS8=2\r] Apr 18 17:31:39 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:39 server FaxGetty[29002]: <-- [8:ATS7=60\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: <-- [12:AT+FCLASS=?\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [15:0,1,2,2.0,6,8,Z] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports "Data" Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports "Class 1" Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports "Class 2" Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports "Class 2.0" Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports "Voice" Apr 18 17:31:40 server FaxGetty[29002]: <-- [12:AT+FCLASS=1\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: <-- [5:ATI3\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [35:ZyXEL ISDN MODEM LINK STATUS REPORT] Apr 18 17:31:40 server FaxGetty[29002]: --> [24:Connect DTE Speed : ] Apr 18 17:31:40 server FaxGetty[29002]: --> [24:Error Control Level : ] Apr 18 17:31:40 server FaxGetty[29002]: --> [24:Protocol Link Speed : ] Apr 18 17:31:40 server FaxGetty[29002]: --> [24:Cause : ] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:Cause Value : 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:Bytes Received : 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:Bytes Sent : 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:HDLC FCS Error : 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:HDLC Receive Overrun : 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [25:HDLC Transmit Underrun: 0] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: MODEM: Mfr ZyXEL ISDN MODEM LINK STATUS REPORT Connect DTE Speed : Error Control Apr 18 17:31:40 server FaxGetty[29002]: <-- [5:ATI0\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [5:28642] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: MODEM: Model 28642 Apr 18 17:31:40 server FaxGetty[29002]: <-- [9:AT+FTM=?\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 3.85 line/mm Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 7.7 line/mm Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 2400 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 4800 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 7200 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 9600 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 12000 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 14400 bit/s Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports page width 1728 pixels in 215 mm Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports page width 2048 pixels in 255 mm Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports page width 2432 pixels in 303 mm Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports A4 page length (297 mm) Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports B4 page length (364 mm) Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports unlimited page length Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 1-D MR Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 2-D MR Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 0 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 5 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 10 ms, 5 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 10 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 20 ms, 10 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 20 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 40 ms, 20 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: MODEM Supports 40 ms/scanline Apr 18 17:31:40 server FaxGetty[29002]: <-- [9:AT+FRM=?\r] Apr 18 17:31:40 server FaxGetty[29002]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Apr 18 17:31:40 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:40 server FaxGetty[29002]: <-- [12:AT+FCLASS=1\r] Apr 18 17:31:41 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:41 server FaxGetty[29002]: MODEM ZYXEL ISDN MODEM LINK STATUS REPORT CONNECT DTE SPEED : ERROR CONTROL LEVELApr 18 17:31:41 server FaxGetty[29002]: <-- [7:ATL0M1\r] Apr 18 17:31:41 server FaxGetty[29002]: --> [2:OK] Apr 18 17:31:41 server FaxGetty[29002]: STATE CHANGE: BASE -> RUNNING Apr 18 17:31:41 server FaxGetty[29002]: MODEM input buffering disabled Apr 18 17:32:48 server kernel: isdn_net: Incoming call without OAD, assuming '0' Apr 18 17:32:48 server kernel: isdn_net: call from 0,1,0 -> 503110867 Apr 18 17:32:48 server kernel: isdn_net: Service-Indicator not 7, ignored Apr 18 17:32:48 server kernel: isdn_tty: Incoming call without OAD, assuming '0' Apr 18 17:32:48 server kernel: isdn_tty: call from 0 -> 503110867 ignored Apr 18 17:32:48 server isdnlog: Apr 18 17:32:48 * Call to tei 127 from ? on +31 50/3110867, Groningen RING (3.1 kHz audio) Apr 18 17:32:48 server FaxGetty[29002]: STATE CHANGE: RUNNING -> LISTENING Apr 18 17:32:48 server FaxGetty[29002]: MODEM input buffering enabled Apr 18 17:32:48 server FaxGetty[29002]: --> [4:RING] Apr 18 17:32:48 server FaxGetty[29002]: MODEM ring left 0 RING Apr 18 17:32:54 server FaxGetty[29002]: --> [12:TO:503110867] Apr 18 17:32:54 server FaxGetty[29002]: MODEM CID TO:503110867 / TO:503110867 Apr 18 17:32:54 server FaxGetty[29002]: --> [4:RING] Apr 18 17:32:54 server FaxGetty[29002]: MODEM ring left 0 RING Apr 18 17:32:54 server FaxGetty[29002]: ANSWER: CID NUMBER "TO:503110867" NAME "TO:503110867" Apr 18 17:33:00 server FaxGetty[29002]: --> [4:RING] Apr 18 17:33:00 server FaxGetty[29002]: MODEM ring left 0 RING Apr 18 17:33:05 server FaxGetty[29002]: --> [4:RING] Apr 18 17:33:05 server FaxGetty[29002]: MODEM ring left 0 RING Apr 18 17:33:05 server isdnlog: Apr 18 17:33:05 Call to tei 97 from ? on +31 50/3110867, Groningen CONNECT (3.1 kHz audio) Apr 18 17:33:05 server isdnlog: Apr 18 17:33:05 tei 80 calling ? with ? Time:Thu Apr 18 17:33:01 2002 Apr 18 17:33:05 server isdnlog: Apr 18 17:33:05 tei 80 calling ? with ? COLP *INVALID* -- ignored! Apr 18 17:33:05 server isdnlog: Apr 18 17:33:05 tei 80 calling ? with ? CONNECT Apr 18 17:33:07 server FaxGetty[29002]: --> [10:NO CARRIER] Apr 18 17:33:07 server FaxGetty[29002]: <-- [5:ATH0\r] Apr 18 17:33:07 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:07 server FaxGetty[29002]: MODEM set DTR OFF Apr 18 17:33:07 server FaxGetty[29002]: MODEM set DTR OFF Apr 18 17:33:07 server FaxGetty[29002]: DELAY 75 ms Apr 18 17:33:07 server FaxGetty[29002]: MODEM set DTR ON Apr 18 17:33:07 server FaxGetty[29002]: DELAY 2600 ms Apr 18 17:33:09 server isdnlog: Apr 18 17:33:09 tei 80 calling ? with ? Normal call clearing (User) Apr 18 17:33:09 server isdnlog: Apr 18 17:33:09 Call to tei 97 from ? on +31 50/3110867, Groningen Normal call clearing (UseApr 18 17:33:09 server isdnlog: Apr 18 17:33:09 Call to tei 97 from ? on +31 50/3110867, Groningen HANGUP ( 0:00:04) Apr 18 17:33:09 server FaxGetty[29002]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF Apr 18 17:33:09 server FaxGetty[29002]: MODEM flush i/o Apr 18 17:33:09 server FaxGetty[29002]: <-- [4:ATZ\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [5:ATE0\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [4:ATE0] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [5:ATV1\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [5:ATQ0\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [7:ATS0=0\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [7:ATS8=2\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [8:ATS7=60\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: <-- [12:AT+FCLASS=?\r] Apr 18 17:33:10 server FaxGetty[29002]: --> [15:0,1,2,2.0,6,8,Z] Apr 18 17:33:10 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports "Data" Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports "Class 1" Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports "Class 2" Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports "Class 2.0" Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports Apr 18 17:33:10 server FaxGetty[29002]: MODEM Supports "Voice" Apr 18 17:33:10 server FaxGetty[29002]: <-- [12:AT+FCLASS=1\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: <-- [5:ATI3\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [35:ZyXEL ISDN MODEM LINK STATUS REPORT] Apr 18 17:33:11 server FaxGetty[29002]: --> [24:Connect DTE Speed : ] Apr 18 17:33:11 server FaxGetty[29002]: --> [24:Error Control Level : ] Apr 18 17:33:11 server FaxGetty[29002]: --> [24:Protocol Link Speed : ] Apr 18 17:33:11 server FaxGetty[29002]: --> [50:Cause : Non-selected user clearing] Apr 18 17:33:11 server FaxGetty[29002]: --> [26:Cause Value : 26] Apr 18 17:33:11 server FaxGetty[29002]: --> [25:Bytes Received : 0] Apr 18 17:33:11 server FaxGetty[29002]: --> [25:Bytes Sent : 0] Apr 18 17:33:11 server FaxGetty[29002]: --> [25:HDLC FCS Error : 0] Apr 18 17:33:11 server FaxGetty[29002]: --> [25:HDLC Receive Overrun : 0] Apr 18 17:33:11 server FaxGetty[29002]: --> [25:HDLC Transmit Underrun: 0] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: MODEM: Mfr ZyXEL ISDN MODEM LINK STATUS REPORT Connect DTE Speed : Error Control Apr 18 17:33:11 server FaxGetty[29002]: <-- [5:ATI0\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [5:28642] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: MODEM: Model 28642 Apr 18 17:33:11 server FaxGetty[29002]: <-- [9:AT+FTM=?\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 3.85 line/mm Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 7.7 line/mm Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 2400 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 4800 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 7200 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 9600 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 12000 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 14400 bit/s Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports page width 1728 pixels in 215 mm Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports page width 2048 pixels in 255 mm Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports page width 2432 pixels in 303 mm Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports A4 page length (297 mm) Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports B4 page length (364 mm) Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports unlimited page length Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 1-D MR Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 2-D MR Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 0 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 5 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 10 ms, 5 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 10 ms, 5 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 10 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 20 ms, 10 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 20 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 40 ms, 20 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: MODEM Supports 40 ms/scanline Apr 18 17:33:11 server FaxGetty[29002]: <-- [9:AT+FRM=?\r] Apr 18 17:33:11 server isdnlog: Apr 18 17:33:11 tei 80 calling ? with ? Normal call clearing (User) Apr 18 17:33:11 server isdnlog: Apr 18 17:33:11 tei 80 calling ? with ? HANGUP ( 0:00:06) Apr 18 17:33:11 server FaxGetty[29002]: --> [41:3,24,48,72,73,74,96,97,98,121,122,145,146] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: <-- [12:AT+FCLASS=1\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: MODEM ZYXEL ISDN MODEM LINK STATUS REPORT CONNECT DTE SPEED : ERROR CONTROL LEVELApr 18 17:33:11 server FaxGetty[29002]: <-- [7:ATL0M1\r] Apr 18 17:33:11 server FaxGetty[29002]: --> [2:OK] Apr 18 17:33:11 server FaxGetty[29002]: STATE CHANGE: LISTENING -> RUNNING Apr 18 17:33:11 server FaxGetty[29002]: MODEM input buffering disabled Apr 18 17:36:24 server isdnlog: Apr 18 17:36:24 * Call to tei 127 from ? on +31 50/3110867, Groningen RING (3.1 kHz audio) ----------- And this is the configuration file: ------------ # $Id: class1,v 1.4 2001/05/21 04:31:28 darren Exp $ # # HylaFAX Facsimile Software # # Copyright (c) 1990-1996 Sam Leffler # Copyright (c) 1991-1996 Silicon Graphics, Inc. # HylaFAX is a trademark of Silicon Graphics, Inc. # # Permission to use, copy, modify, distribute, and sell this software and # its documentation for any purpose is hereby granted without fee, provided # that (i) the above copyright notices and this permission notice appear in # all copies of the software and related documentation, and (ii) the names of # Sam Leffler and Silicon Graphics may not be used in any advertising or # publicity relating to the software without the specific, prior written # permission of Sam Leffler and Silicon Graphics. # # THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, # EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY # WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. # # IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR # ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, # OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, # WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF # LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE # OF THIS SOFTWARE. # # # Generic Class 1 modem configuration. # # EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP # CountryCode: 31 AreaCode: 50 FAXNumber: 3110867 LongDistancePrefix: 0 InternationalPrefix: 00 DialStringRules: etc/dialrules.europe ServerTracing: 0xFFF SessionTracing: 1 RecvFileMode: 0600 LogFileMode: 0600 DeviceMode: 0600 RingsBeforeAnswer: 0 SpeakerVolume: quiet GettyArgs: "" # # # Modem-related stuff: should reflect modem command interface # and hardware connection/cabling (e.g. flow control). # ModemType: Class1 # use this to supply a hint #ModemRate: 19200 # rate for DCE-DTE communication #ModemFlowControl: xonxoff # XON/XOFF flow control assumed # #ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem #ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier #GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data # # We normally append the "@" symbol to the dial string so that # the modem will wait 5 seconds before attempting to connect # and return result codes that distinguish between no carrier # and no answer. This makes it possible to avoid problems with # repeatedly dialing a number that doesn't have a fax machine # (kudos to Stuart Lynne for this trick.) # # NB: If you need to prefix phone numbers to get through a PBX, # put it in the ModemDialCmd; e.g. "DT9%s@". # #ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence # # Other possible configuration stuff. The default strings are # shown below. Only those that are different from the defaults # need to be included in the configuration file. # #ModemResetCmds: "" # stuff to do when modem is reset #ModemAnswerCmd: ATA # use this to answer phone #ModemNoFlowCmd: AT&K # disable flow control cmd #ModemHardFlowCmd: AT&K3 # hardware flow control cmd #ModemSoftFlowCmd: AT&K4 # software flow control cmd #ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer # # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH. # Note that we both turn the speaker on/off and set volume. # #ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1" #ModemEchoOffCmd: ATE0 # disable command echo #ModemVerboseResultsCmd: ATV1 # enable verbose command results #ModemResultCodesCmd: ATQ0 # enable result codes #ModemOnHookCmd: ATH0 # place phone on hook (hangup) #ModemSoftResetCmd: ATZ # do soft reset of modem #ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit # Class1Cmd: AT+FCLASS=1 # command to enter class 1 Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response Class1SendPPMDelay: 75 # 75ms delay before sending PPM Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF Class1SwitchingDelay: 150 # 150ms delay in switching transmission direction Class1TrainingRecovery: 1500 # 1.5sec delay after training failure Class1RecvAbortOK: 200 # wait 200ms for abort response Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration --------- ____________________ HylaFAX(tm) Users Mailing List _______________________ To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi On UNIX: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null
- Follow-Ups:
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Lee Howard
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- References:
- [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Paul van der Vlis
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Lee Howard
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Paul van der Vlis
- Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- From: Lee Howard
- [hylafax-users] No response to MPS or EOP repeated 3 tries
- Prev by Date: [hylafax-users] Unspecified Transmit Phase D error
- Next by Date: Re: [hylafax-users] Unspecified Transmit Phase D error
- Previous by thread: Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- Next by thread: Re: [hylafax-users] No response to MPS or EOP repeated 3 tries
- Index(es):
Project hosted by iFAX Solutions