[hylafax-users] Hylafax & Acceleport RAS 8

["Alex S. Pereira" <aspereira@ig.com.br>]

Hi,

I have a server with Red Hat 7.2 and Hylafax 4.1.1, I am testing a
multimodem card from DIGI called AccelePort RAS 8, I guess that is a good
card, the percentual of failure that was 40% with USRobotics modem, now is
4,8% with this multimodem card, I am just having one problem, some incoming
faxes miss some horizontal lines, the transmission is OK but the printed
faxes miss some horizontal lines, in some case the first page is OK and the
others is wrong, my config is :

 

#

# Generic Class 2.0 modem configuration.

#

# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP

#

CountryCode: 55

AreaCode: 11

FAXNumber: 5509-0382

LongDistancePrefix: 21

InternationalPrefix: 21

DialStringRules: etc/dialrules

ServerTracing: 127

SessionTracing: 127

RecvFileMode: 0644

LogFileMode: 0644

DeviceMode: 0600

RingsBeforeAnswer: 1

SpeakerVolume: off

GettyArgs: "-h %l dx_%s"

LocalIdentifier: Continental

TagLineFont: etc/lutRS18.pcf

TagLineFormat: "From %%l|%c|Page %%P of %%T"

PercentGoodLines: 5

MaxConsecutiveBadLines: 10

MaxRecvPages: 100

FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd02

#

#

# Modem-related stuff: should reflect modem command interface

# and hardware connection/cabling (e.g. flow control).

#

ModemType: Class2.0 # use this to supply a hint

#ModemRate: 19200 # max rate for DCE-DTE communication

#ModemFlowControl: xonxoff # XON/XOFF flow control assumed

#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem

#ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)

#

# We normally append the "@" symbol to the dial string so that

# the modem will wait 5 seconds before attempting to connect

# and return result codes that distinguish between no carrier

# and no answer. This makes it possible to avoid problems with

# repeatedly dialing a number that doesn't have a fax machine

# (kudos to Stuart Lynne for this trick.)

#

# NB: If you need to prefix phone numbers to get through a PBX,

# put it in the ModemDialCmd; e.g. "DT9%s@".

#

#ModemDialCmd: ATDT%s@ # T for tone dialing, @ for silence

#

# Other possible configuration stuff. The default strings are

# shown below. Only those that are different from the defaults

# need to be included in the configuration file.

#

#ModemResetCmds: "" # stuff to do when modem is reset

#ModemAnswerCmd: ATA # use this to answer phone

#ModemNoFlowCmd: AT&K # disable flow control cmd

#ModemHardFlowCmd: AT&K3 # hardware flow control cmd

#ModemSoftFlowCmd: AT&K4 # software flow control cmd

#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer

#

# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.

# Note that we both turn the speaker on/off and set volume.

#

#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"

#ModemEchoOffCmd: ATE0 # disable command echo

#ModemVerboseResultsCmd: ATV1 # enable verbose command results

#ModemResultCodesCmd: ATQ0 # enable result codes

#ModemOnHookCmd: ATH0 # place phone on hook (hangup)

#ModemSoftResetCmd: ATZ # do soft reset of modem

#ModemSoftResetCmdDelay: 3000 # pause after soft reset

#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier

#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds

#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile

#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit

#

# Configuration parameters for Class 2.0 modems.

#

Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0

Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)

Class2CQCmd: "" # commands to enable copy quality proc.

Class2AbortCmd: AT+FKS # abort session command

Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities

Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities

Class2TBCCmd: AT+FPP=0 # setup stream mode

Class2CRCmd: AT+FCR=1 # enable capability to receive

Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter

Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing

Class2LIDCmd: AT+FLI # set local identifier command

Class2DCCCmd: AT+FCC # set modem capabilities command

Class2DISCmd: AT+FIS # set session parameters command

Class2DDISCmd: "" # disable pre-dial DIS command hack

Class2CIGCmd: AT+FPI # set polling identifier command

Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command

Class2PIECmd: AT+FIE=0 # disable interrupt-enable command

Class2PTSCmd: AT+FPS # set post-page status command

Class2SPLCmd: AT+FSP # set polling indicator command

Class2NFLOCmd: AT+FLO=0 # set no flow control command

Class2SFLOCmd: AT+FLO=1 # set software flow control command

Class2HFLOCmd: AT+FLO=2 # set hardware flow control command

 

This is the transmission log :

 

Mar 28 13:26:53.19: [19480]: SESSION BEGIN 00000388 551155090377

Mar 28 13:26:53.19: [19480]: HylaFAX (tm) Version 4.1.1

Mar 28 13:26:53.19: [19480]: <-- [4:ATA\r]

Mar 28 13:26:59.05: [19480]: --> [74:+FHT: FF 03 40 20 20 20 20 20 20 20 20 20 6C 61 74 6E 65 6E 69 74 6E 6F 43]

Mar 28 13:26:59.33: [19480]: --> [26:+FHT: FF 13 80 00 EE FA 46]

Mar 28 13:27:04.31: [19480]: --> [74:+FHT: FF 03 40 20 20 20 20 20 20 20 20 20 6C 61 74 6E 65 6E 69 74 6E 6F 43]

Mar 28 13:27:04.59: [19480]: --> [26:+FHT: FF 13 80 00 EE FA 46]

Mar 28 13:27:05.45: [19480]: --> [4:+FCO]

Mar 28 13:27:05.45: [19480]: ANSWER: FAX CONNECTION DEVICE '/dev/ttyG0_00'

Mar 28 13:27:05.45: [19480]: MODEM input buffering enabled

Mar 28 13:27:05.45: [19480]: RECV FAX: begin

Mar 28 13:27:07.04: [19480]: --> [74:+FHR: FF 03 43 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20]

Mar 28 13:27:07.39: [19480]: --> [26:+FHR: FF 13 83 00 86 88 00]

Mar 28 13:27:07.39: [19480]: --> [27:+FTI:" "]

Mar 28 13:27:07.39: [19480]: REMOTE TSI ""

Mar 28 13:27:07.39: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:27:07.39: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:27:07.39: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:27:07.39: [19480]: REMOTE wants unlimited page length

Mar 28 13:27:07.39: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:27:07.39: [19480]: REMOTE wants 2-D MR

Mar 28 13:27:07.39: [19480]: --> [2:OK]

Mar 28 13:27:07.39: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:27:10.75: [19480]: --> [14:+FHT: FF 13 84]

Mar 28 13:27:11.89: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:27:11.89: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:27:11.89: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:27:11.89: [19480]: REMOTE wants unlimited page length

Mar 28 13:27:11.89: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:27:11.89: [19480]: REMOTE wants 2-D MR

Mar 28 13:27:11.89: [19480]: --> [7:CONNECT]

Mar 28 13:27:11.89: [19480]: RECV: begin page

Mar 28 13:27:11.89: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:27:11.92: [19480]: RECV: send trigger 022

Mar 28 13:27:11.92: [19480]: <-- data [1]

Mar 28 13:27:48.87: [19480]: RECV: 25233 bytes of data, 929 total lines

Mar 28 13:27:48.87: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:27:50.15: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:27:50.15: [19480]: --> [16:+FPS:1,929,1,0,0]

Mar 28 13:27:50.15: [19480]: --> [6:+FET:0]

Mar 28 13:27:50.15: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:27:50.15: [19480]: --> [2:OK]

Mar 28 13:27:50.15: [19480]: RECV send MCF (message confirmation)

Mar 28 13:27:50.15: [19480]: RECV FAX (00000388): from , page 1 in 0:43, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:27:50.15: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:27:51.66: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:27:52.77: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:27:52.77: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:27:52.77: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:27:52.77: [19480]: REMOTE wants unlimited page length

Mar 28 13:27:52.77: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:27:52.77: [19480]: REMOTE wants 2-D MR

Mar 28 13:27:52.77: [19480]: --> [7:CONNECT]

Mar 28 13:27:52.77: [19480]: RECV: begin page

Mar 28 13:27:52.77: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:27:52.79: [19480]: RECV: send trigger 022

Mar 28 13:27:52.79: [19480]: <-- data [1]

Mar 28 13:28:33.38: [19480]: RECV: 25468 bytes of data, 1159 total lines

Mar 28 13:28:33.38: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:28:34.69: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:28:34.69: [19480]: --> [17:+FPS:1,1160,1,0,0]

Mar 28 13:28:34.69: [19480]: --> [6:+FET:0]

Mar 28 13:28:34.69: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:28:34.69: [19480]: --> [2:OK]

Mar 28 13:28:34.69: [19480]: RECV send MCF (message confirmation)

Mar 28 13:28:34.69: [19480]: RECV FAX (00000388): from , page 2 in 0:44, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:28:34.69: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:28:36.19: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:28:37.32: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:28:37.32: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:28:37.32: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:28:37.32: [19480]: REMOTE wants unlimited page length

Mar 28 13:28:37.32: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:28:37.32: [19480]: REMOTE wants 2-D MR

Mar 28 13:28:37.32: [19480]: --> [7:CONNECT]

Mar 28 13:28:37.32: [19480]: RECV: begin page

Mar 28 13:28:37.32: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:28:37.34: [19480]: RECV: send trigger 022

Mar 28 13:28:37.34: [19480]: <-- data [1]

Mar 28 13:29:09.23: [19480]: RECV: 16503 bytes of data, 1143 total lines

Mar 28 13:29:09.23: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:29:10.54: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:29:10.54: [19480]: --> [17:+FPS:1,1144,1,0,0]

Mar 28 13:29:10.54: [19480]: --> [6:+FET:0]

Mar 28 13:29:10.54: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:29:10.54: [19480]: --> [2:OK]

Mar 28 13:29:10.54: [19480]: RECV send MCF (message confirmation)

Mar 28 13:29:10.54: [19480]: RECV FAX (00000388): from , page 3 in 0:36, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:29:10.54: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:29:12.05: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:29:13.18: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:29:13.18: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:29:13.18: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:29:13.18: [19480]: REMOTE wants unlimited page length

Mar 28 13:29:13.18: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:29:13.18: [19480]: REMOTE wants 2-D MR

Mar 28 13:29:13.18: [19480]: --> [7:CONNECT]

Mar 28 13:29:13.18: [19480]: RECV: begin page

Mar 28 13:29:13.18: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:29:13.20: [19480]: RECV: send trigger 022

Mar 28 13:29:13.20: [19480]: <-- data [1]

Mar 28 13:29:45.56: [19480]: RECV: 17262 bytes of data, 1201 total lines

Mar 28 13:29:45.56: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:29:46.87: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:29:46.87: [19480]: --> [17:+FPS:1,1201,1,0,0]

Mar 28 13:29:46.87: [19480]: --> [6:+FET:0]

Mar 28 13:29:46.87: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:29:46.87: [19480]: --> [2:OK]

Mar 28 13:29:46.87: [19480]: RECV send MCF (message confirmation)

Mar 28 13:29:46.87: [19480]: RECV FAX (00000388): from , page 4 in 0:36, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:29:46.87: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:29:48.38: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:29:49.48: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:29:49.48: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:29:49.48: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:29:49.48: [19480]: REMOTE wants unlimited page length

Mar 28 13:29:49.48: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:29:49.48: [19480]: REMOTE wants 2-D MR

Mar 28 13:29:49.48: [19480]: --> [7:CONNECT]

Mar 28 13:29:49.48: [19480]: RECV: begin page

Mar 28 13:29:49.48: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:29:49.50: [19480]: RECV: send trigger 022

Mar 28 13:29:49.50: [19480]: <-- data [1]

Mar 28 13:30:23.49: [19480]: RECV: 17839 bytes of data, 1153 total lines

Mar 28 13:30:23.49: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:30:24.79: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:30:24.79: [19480]: --> [17:+FPS:1,1153,1,0,0]

Mar 28 13:30:24.79: [19480]: --> [6:+FET:0]

Mar 28 13:30:24.79: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:30:24.79: [19480]: --> [2:OK]

Mar 28 13:30:24.79: [19480]: RECV send MCF (message confirmation)

Mar 28 13:30:24.79: [19480]: RECV FAX (00000388): from , page 5 in 0:38, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:30:24.79: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:30:26.30: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:30:27.41: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:30:27.41: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:30:27.41: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:30:27.41: [19480]: REMOTE wants unlimited page length

Mar 28 13:30:27.41: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:30:27.41: [19480]: REMOTE wants 2-D MR

Mar 28 13:30:27.41: [19480]: --> [7:CONNECT]

Mar 28 13:30:27.41: [19480]: RECV: begin page

Mar 28 13:30:27.41: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:30:27.43: [19480]: RECV: send trigger 022

Mar 28 13:30:27.43: [19480]: <-- data [1]

Mar 28 13:31:02.96: [19480]: RECV: 23106 bytes of data, 967 total lines

Mar 28 13:31:02.96: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:31:04.27: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:31:04.27: [19480]: --> [16:+FPS:1,968,1,0,0]

Mar 28 13:31:04.27: [19480]: --> [6:+FET:0]

Mar 28 13:31:04.27: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:31:04.27: [19480]: --> [2:OK]

Mar 28 13:31:04.27: [19480]: RECV send MCF (message confirmation)

Mar 28 13:31:04.27: [19480]: RECV FAX (00000388): from , page 6 in 0:40, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:31:04.27: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:31:05.78: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:31:06.88: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:31:06.88: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:31:06.88: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:31:06.88: [19480]: REMOTE wants unlimited page length

Mar 28 13:31:06.88: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:31:06.88: [19480]: REMOTE wants 2-D MR

Mar 28 13:31:06.88: [19480]: --> [7:CONNECT]

Mar 28 13:31:06.88: [19480]: RECV: begin page

Mar 28 13:31:06.88: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:31:06.91: [19480]: RECV: send trigger 022

Mar 28 13:31:06.91: [19480]: <-- data [1]

Mar 28 13:31:43.52: [19480]: RECV: 22199 bytes of data, 1165 total lines

Mar 28 13:31:43.52: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:31:44.83: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:31:44.83: [19480]: --> [17:+FPS:1,1166,1,0,0]

Mar 28 13:31:44.83: [19480]: --> [6:+FET:0]

Mar 28 13:31:44.83: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:31:44.83: [19480]: --> [2:OK]

Mar 28 13:31:44.83: [19480]: RECV send MCF (message confirmation)

Mar 28 13:31:44.83: [19480]: RECV FAX (00000388): from , page 7 in 0:40, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:31:44.83: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:31:46.34: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:31:47.45: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:31:47.45: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:31:47.45: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:31:47.45: [19480]: REMOTE wants unlimited page length

Mar 28 13:31:47.45: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:31:47.45: [19480]: REMOTE wants 2-D MR

Mar 28 13:31:47.45: [19480]: --> [7:CONNECT]

Mar 28 13:31:47.45: [19480]: RECV: begin page

Mar 28 13:31:47.45: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:31:47.47: [19480]: RECV: send trigger 022

Mar 28 13:31:47.47: [19480]: <-- data [1]

Mar 28 13:32:19.62: [19480]: RECV: 20695 bytes of data, 1151 total lines

Mar 28 13:32:19.62: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:32:20.91: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:32:20.91: [19480]: --> [17:+FPS:1,1151,1,0,0]

Mar 28 13:32:20.91: [19480]: --> [6:+FET:0]

Mar 28 13:32:20.91: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:32:20.91: [19480]: --> [2:OK]

Mar 28 13:32:20.91: [19480]: RECV send MCF (message confirmation)

Mar 28 13:32:20.91: [19480]: RECV FAX (00000388): from , page 8 in 0:36, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:32:20.91: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:32:22.42: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:32:23.52: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:32:23.52: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:32:23.52: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:32:23.52: [19480]: REMOTE wants unlimited page length

Mar 28 13:32:23.52: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:32:23.52: [19480]: REMOTE wants 2-D MR

Mar 28 13:32:23.52: [19480]: --> [7:CONNECT]

Mar 28 13:32:23.52: [19480]: RECV: begin page

Mar 28 13:32:23.52: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:32:23.54: [19480]: RECV: send trigger 022

Mar 28 13:32:23.54: [19480]: <-- data [1]

Mar 28 13:32:54.41: [19480]: RECV: 19807 bytes of data, 1153 total lines

Mar 28 13:32:54.41: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:32:55.72: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:32:55.72: [19480]: --> [17:+FPS:1,1153,1,0,0]

Mar 28 13:32:55.72: [19480]: --> [6:+FET:0]

Mar 28 13:32:55.72: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:32:55.72: [19480]: --> [2:OK]

Mar 28 13:32:55.72: [19480]: RECV send MCF (message confirmation)

Mar 28 13:32:55.72: [19480]: RECV FAX (00000388): from , page 9 in 0:35, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:32:55.72: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:32:57.23: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:32:58.35: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:32:58.35: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:32:58.35: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:32:58.35: [19480]: REMOTE wants unlimited page length

Mar 28 13:32:58.35: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:32:58.35: [19480]: REMOTE wants 2-D MR

Mar 28 13:32:58.35: [19480]: --> [7:CONNECT]

Mar 28 13:32:58.35: [19480]: RECV: begin page

Mar 28 13:32:58.35: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:32:58.37: [19480]: RECV: send trigger 022

Mar 28 13:32:58.37: [19480]: <-- data [1]

Mar 28 13:33:29.13: [19480]: RECV: 19712 bytes of data, 1161 total lines

Mar 28 13:33:29.13: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:33:30.43: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:33:30.43: [19480]: --> [17:+FPS:1,1161,1,0,0]

Mar 28 13:33:30.43: [19480]: --> [6:+FET:0]

Mar 28 13:33:30.43: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:33:30.43: [19480]: --> [2:OK]

Mar 28 13:33:30.43: [19480]: RECV send MCF (message confirmation)

Mar 28 13:33:30.43: [19480]: RECV FAX (00000388): from , page 10 in 0:35, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:33:30.43: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:33:31.94: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:33:33.07: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:33:33.07: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:33:33.07: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:33:33.07: [19480]: REMOTE wants unlimited page length

Mar 28 13:33:33.07: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:33:33.07: [19480]: REMOTE wants 2-D MR

Mar 28 13:33:33.07: [19480]: --> [7:CONNECT]

Mar 28 13:33:33.07: [19480]: RECV: begin page

Mar 28 13:33:33.07: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:33:33.09: [19480]: RECV: send trigger 022

Mar 28 13:33:33.09: [19480]: <-- data [1]

Mar 28 13:34:04.75: [19480]: RECV: 19696 bytes of data, 1153 total lines

Mar 28 13:34:04.75: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:34:06.03: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:34:06.03: [19480]: --> [17:+FPS:1,1154,1,0,0]

Mar 28 13:34:06.03: [19480]: --> [6:+FET:0]

Mar 28 13:34:06.03: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:34:06.03: [19480]: --> [2:OK]

Mar 28 13:34:06.03: [19480]: RECV send MCF (message confirmation)

Mar 28 13:34:06.03: [19480]: RECV FAX (00000388): from , page 11 in 0:36, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:34:06.03: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:34:07.54: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:34:08.65: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:34:08.65: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:34:08.65: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:34:08.65: [19480]: REMOTE wants unlimited page length

Mar 28 13:34:08.65: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:34:08.65: [19480]: REMOTE wants 2-D MR

Mar 28 13:34:08.65: [19480]: --> [7:CONNECT]

Mar 28 13:34:08.65: [19480]: RECV: begin page

Mar 28 13:34:08.65: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:34:08.67: [19480]: RECV: send trigger 022

Mar 28 13:34:08.67: [19480]: <-- data [1]

Mar 28 13:34:39.40: [19480]: RECV: 19739 bytes of data, 1163 total lines

Mar 28 13:34:39.40: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:34:40.71: [19480]: --> [14:+FHR: FF 13 4F]

Mar 28 13:34:40.71: [19480]: --> [17:+FPS:1,1163,1,0,0]

Mar 28 13:34:40.71: [19480]: --> [6:+FET:0]

Mar 28 13:34:40.71: [19480]: RECV recv MPS (more pages, same document)

Mar 28 13:34:40.71: [19480]: --> [2:OK]

Mar 28 13:34:40.71: [19480]: RECV send MCF (message confirmation)

Mar 28 13:34:40.71: [19480]: RECV FAX (00000388): from , page 12 in 0:34, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:34:40.71: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:34:42.22: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:34:43.32: [19480]: --> [20:+FCS:0,3,0,2,1,0,0,5]

Mar 28 13:34:43.32: [19480]: REMOTE wants 9600 bit/s

Mar 28 13:34:43.32: [19480]: REMOTE wants page width 1728 pixels in 215 mm

Mar 28 13:34:43.32: [19480]: REMOTE wants unlimited page length

Mar 28 13:34:43.32: [19480]: REMOTE wants 3.85 line/mm

Mar 28 13:34:43.32: [19480]: REMOTE wants 2-D MR

Mar 28 13:34:43.32: [19480]: --> [7:CONNECT]

Mar 28 13:34:43.32: [19480]: RECV: begin page

Mar 28 13:34:43.32: [19480]: MODEM set XON/XOFF/FLUSH: input ignored, output generated

Mar 28 13:34:43.34: [19480]: RECV: send trigger 022

Mar 28 13:34:43.34: [19480]: <-- data [1]

Mar 28 13:35:17.31: [19480]: RECV: 18201 bytes of data, 1155 total lines

Mar 28 13:35:17.31: [19480]: MODEM set XON/XOFF/DRAIN: input interpreted, output disabled

Mar 28 13:35:18.61: [19480]: --> [14:+FHR: FF 13 2F]

Mar 28 13:35:18.61: [19480]: --> [17:+FPS:1,1155,1,0,0]

Mar 28 13:35:18.61: [19480]: --> [6:+FET:2]

Mar 28 13:35:18.61: [19480]: RECV recv EOP (no more pages or documents)

Mar 28 13:35:18.61: [19480]: --> [2:OK]

Mar 28 13:35:18.61: [19480]: RECV send MCF (message confirmation)

Mar 28 13:35:18.61: [19480]: RECV FAX (00000388): from , page 13 in 0:38, INF, 3.85 line/mm, 2-D MR, 9600 bit/s

Mar 28 13:35:18.61: [19480]: RECV FAX (00000388): recvq/fax00364.tif from , route to <unspecified>, 13 pages in 8:13

Mar 28 13:35:18.61: [19480]: <-- [7:AT+FDR\r]

Mar 28 13:35:20.12: [19480]: --> [14:+FHT: FF 13 8C]

Mar 28 13:35:20.12: [19480]: RECV FAX: /var/spool/hylafax/bin/faxrcvd01 "recvq/fax00364.tif" "ttyG0_00" "00000388" "" "" ""

Mar 28 13:35:23.74: [19480]: RECV FAX: end

Mar 28 13:35:23.74: [19480]: SESSION END

 

 

Like you can see, don't have error, but the all pages miss the horizontal lines, someone can help me ?

 

Thanks,

Alex