Re: [hylafax-users] 3com sportser and hyla sorry 3com faxmodem

["Massimo Donato" <tecnico@adcom.it>]

sorry for the errror the modem is "3com faxmodem"
----- Original Message -----
From: "Massimo Donato" <tecnico@adcom.it>
To: <hylafax-users@hylafax.org>
Sent: Monday, March 11, 2002 9:27 AM
Subject: [hylafax-users] 3com sportser and hyla


> Hi everyone,
>     As suggested by Lee Howard i changed my configuration of hyla to class
> one , all ok about receving !!! Thank you very much.
>
> Sending of fax is very difficult now, the most common error is no carrier
> detected.
>
> here is my conf file, anyone who has any suggestion ???
>
>
> # Generic Class 1 modem configuration.
>
> # BEGIN-SERVER
>
> CountryCode: 39
>
> LongDistancePrefix: 0
>
> InternationalPrefix: 00
>
> AreaCode: 051
>
> DialStringRules: etc/dialrules
>
> FAXNumber: +39051xxxxxxx
>
> LocalIdentifier: "xxxxxxx"
>
> ServerTracing: 1
>
> SessionTracing: 11
>
> RecvFileMode: 0666
>
> LogFileMode: 0600
>
> DeviceMode: 0600
>
> #QualifyTSI: etc/tsi # accept facsimile from anyone
>
> SpeakerVolume: off
>
> RingsBeforeAnswer: 2
>
> TagLineFont: etc/lutRS18.pcf
>
> TagLineFormat: "Da %%l|%c|Pagina %%P di %%T"
>
> #MaxBadCalls: 5
>
> PostScriptTimeout: 300
>
> MaxSendPages: 50
>
> MaxRecvPages: 50
>
> #ContCoverPage: etc/cover.templ # enable continuation cover pages
>
> #DestControls: etc/destcontrols # destination-specific controls
>
> #MaxConcurrentJobs: 1 # serialize jobs to the same dest
>
> #TimeOfDay: "Any" # outbound jobs any day, any time
>
> # END-SERVER
>
> #
>
> # Modem-related stuff: should reflect modem command interface
>
> # and hardware connection/cabling (e.g. flow control).
>
> #
>
> ModemType: Class1 # use this to supply a hint
>
> ModemRate: 19200 # rate for DCE-DTE communication
>
> ModemFlowControl: rtscts # XON/XOFF flow control assumed
>
> #
>
> ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
>
> ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
>
> GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
>
> ModemDialCmd: ATS7=100DT%s@ # T for tone dialing, @ for silence
>
> #
>
> #ModemNoFlowCmd AT&H0&I0&R1
>
> #ModemHardFlowCmd AT&H1&I0&R2
>
> #ModemSoftFlowCmd AT&H2&I2&R1
>
> ModemResetCmds: "" # stuff to do when modem is reset
>
> ModemAnswerCmd: ATA # use this to answer phone
>
> ModemNoFlowCmd: AT&K # disable flow control cmd
>
> ModemHardFlowCmd: AT&K3 # hardware flow control cmd
>
> ModemSoftFlowCmd: AT&K4 # software flow control cmd
>
> ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
>
> #
>
> # Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
>
> # Note that we both turn the speaker on/off and set volume.
>
> #
>
> ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
>
> ModemEchoOffCmd: ATE0 # disable command echo
>
> ModemVerboseResultsCmd: ATV1 # enable verbose command results
>
> ModemResultCodesCmd: ATQ0 # enable result codes
>
> ModemOnHookCmd: ATH0 # place phone on hook (hangup)
>
> ModemSoftResetCmd: ATZ # do soft reset of modem
>
> ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
>
> #ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
>
> #ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
>
> #ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
>
> #
>
> Class1Cmd: AT+FCLASS=1 # command to enter class 1
>
> Class1TCFResponseDelay: 75 # 75ms delay between recv TCF & response
>
> Class1SendPPMDelay: 75 # 75ms delay before sending PPM
>
> Class1SendTCFDelay: 75 # 75ms delay between sending DCS & TCF
>
> Class1SwitchingDelay: 150 # 150ms delay in switching transmission
direction
>
> Class1TrainingRecovery: 1500 # 1.5sec delay after training failure
>
> Class1RecvAbortOK: 200 # wait 200ms for abort response
>
> Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
>
> Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
>
> Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
>
> Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
>
>
>
>
>
> Massimo Donato
>
> e-mail tecnico@adcom.it
>
>
>
> ____________________ HylaFAX(tm) Users Mailing List
_______________________
>  To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org <
/dev/null
>


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null