[hylafax-users] Can't Receive Faxes - --> [10:NO CARRIER]

["Burath, Philipp" <Philipp.Burath@maynegroup.com>]

Hi,

I have just setup Hylafax 4.1.1 with Redhat 6.1 from the source
distribution. I haven't been able to receive any faxes as I get a [10:NO
CARRIER]. Modem is setup as class 1. I can send faxes fine. When it tries to
receive a fax it sits at "RECV: begin page" with the "off hook" light on and
faxstat sits on "Receiving from XXXX". I have tried turning Adaptive answer
off with AT+FAA=0 but this hasn't resolved the problem. 

Any ideas?

Feb 28 10:02:05.75: [ 8046]: SESSION BEGIN 00000002 610893171536
Feb 28 10:02:05.75: [ 8046]: HylaFAX (tm) Version 4.1.1
Feb 28 10:02:05.76: [ 8046]: <-- [4:ATA\r]
Feb 28 10:02:11.21: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:11.22: [ 8046]: ANSWER: FAX CONNECTION  DEVICE '/dev/ttyE0'
Feb 28 10:02:11.22: [ 8046]: MODEM input buffering enabled
Feb 28 10:02:11.22: [ 8046]: RECV FAX: begin
Feb 28 10:02:11.22: [ 8046]: MODEM input buffering disabled
Feb 28 10:02:11.22: [ 8046]: <-- data [23]
Feb 28 10:02:11.22: [ 8046]: <-- data [2]
Feb 28 10:02:12.90: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:12.90: [ 8046]: <-- data [10]
Feb 28 10:02:12.90: [ 8046]: <-- data [2]
Feb 28 10:02:13.44: [ 8046]: --> [2:OK]
Feb 28 10:02:13.44: [ 8046]: <-- [9:AT+FRH=3\r]
Feb 28 10:02:14.31: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:15.71: [ 8046]: --> [2:OK]
Feb 28 10:02:15.71: [ 8046]: REMOTE TSI "+61 8 93171536"
Feb 28 10:02:15.71: [ 8046]: <-- [9:AT+FRH=3\r]
Feb 28 10:02:15.72: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:15.98: [ 8046]: --> [2:OK]
Feb 28 10:02:15.98: [ 8046]: REMOTE wants 14400 bit/s
Feb 28 10:02:15.98: [ 8046]: REMOTE wants page width 1728 pixels in 215 mm
Feb 28 10:02:15.98: [ 8046]: REMOTE wants unlimited page length
Feb 28 10:02:15.98: [ 8046]: REMOTE wants 3.85 line/mm
Feb 28 10:02:15.98: [ 8046]: REMOTE wants 2-D MR
Feb 28 10:02:15.98: [ 8046]: RECV training at v.17 14400 bit/s
Feb 28 10:02:15.98: [ 8046]: <-- [11:AT+FRM=145\r]
Feb 28 10:02:17.70: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:19.26: [ 8046]: RECV: TCF 2756 bytes, 1% non-zero, 2710
zero-run
Feb 28 10:02:19.27: [ 8046]: --> [10:NO CARRIER]
Feb 28 10:02:19.27: [ 8046]: DELAY 75 ms
Feb 28 10:02:19.35: [ 8046]: TRAINING succeeded
Feb 28 10:02:19.35: [ 8046]: <-- [9:AT+FTH=3\r]
Feb 28 10:02:19.41: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:19.41: [ 8046]: <-- data [3]
Feb 28 10:02:19.41: [ 8046]: <-- data [2]
Feb 28 10:02:20.72: [ 8046]: --> [2:OK]
Feb 28 10:02:20.72: [ 8046]: MODEM input buffering enabled
Feb 28 10:02:20.72: [ 8046]: <-- [11:AT+FRM=146\r]
Feb 28 10:02:21.68: [ 8046]: --> [7:CONNECT]
Feb 28 10:02:21.68: [ 8046]: RECV: begin page
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Invalid BlackTable code word, row 0, x
0
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Invalid BlackTable code word, row 0, x
0
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Bad 1D pixel count, row 0, got 0,
expected 1728
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Invalid MainTable code word, row 1, x
0
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Bad 2D pixel count, row 1, got 0,
expected 1728
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Invalid BlackTable code word, row 2, x
0
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Bad 1D pixel count, row 2, got 0,
expected 1728
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Invalid MainTable code word, row 3, x
0
Feb 28 10:02:21.76: [ 8046]: RECV/CQ: Bad 2D pixel count, row 3, got 0,
expected 1728
Feb 28 10:02:21.83: [ 8046]: RECV/CQ: Invalid WhiteTable code word, row 4, x
0
Feb 28 10:02:21.83: [ 8046]: RECV/CQ: Bad 1D pixel count, row 4, got 0,
expected 1728
Feb 28 10:02:21.91: [ 8046]: RECV/CQ: Invalid BlackTable code word, row 5, x
0
Feb 28 10:02:21.91: [ 8046]: RECV/CQ: Bad 2D pixel count, row 5, got 0,
expected 1728
Feb 28 10:02:21.91: [ 8046]: RECV/CQ: Invalid WhiteTable code word, row 6, x
0
Feb 28 10:02:21.91: [ 8046]: RECV/CQ: Bad 1D pixel count, row 6, got 0,
expected 1728
Feb 28 10:02:21.99: [ 8046]: RECV/CQ: Invalid WhiteTable code word, row 8, x
0
Feb 28 10:02:21.99: [ 8046]: RECV/CQ: Bad 1D pixel count, row 8, got 0,
expected 1728
Feb 28 10:02:22.07: [ 8046]: RECV/CQ: Invalid WhiteTable code word, row 10,
x 0
Feb 28 10:02:22.07: [ 8046]: RECV/CQ: Bad 1D pixel count, row 10, got 0,
expected 1728
Feb 28 10:02:22.14: [ 8046]: RECV/CQ: Invalid MainTable code word, row 11, x
0
Feb 28 10:02:22.14: [ 8046]: RECV/CQ: Bad 2D pixel count, row 11, got 0,
expected 1728
Feb 28 10:02:22.22: [ 8046]: RECV/CQ: Invalid BlackTable code word, row 12,
x 0
..
..
..

and just keeps going. Could it be libtiff...using verison 3.5.7.

Thank you.

============================================
Philipp Burath
IT Network Support Consultant
Mayne Health - Western Diagnostic Pathology
74 Mc Coy Street Myaree WA 6154
Perth, Australia
Ph - 9317 0717
philipp.burath@maynegroup.com
============================================ 


**********************************************************************
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they
are addressed. If you have received this email in error please notify
the system manager.

This footnote also confirms that this email message has been swept by
MIMEsweeper for the presence of computer viruses.

www.mimesweeper.com
**********************************************************************


____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null