[hylafax-users] send works with USR only

[Lee Howard <faxguy@deanox.com>]

Dmitry, are you out there?

Here's an interesting issue.  Attached are three send logs.  When trying to
send from any non-Class-2.0-capable modem (I've tried at least four
different modems, including a USR-Class-1-only modem) in Class 1 the send
fails with "no carrier detected".  When trying to send in Class 2 (I've
only tried one modem, but two attempts) the send fails with "No answer
(T.30 T1 timeout)".  However, when sending from a Class-2.0-capable modem,
whether using Class 1 or Class 2.0, the send goes fine.

I get "no carrier detected" on and off quite a bit, but usually on the
second attempt the send works fine.  Normally I'd chalk this up as a bad
config file, but where the send fails identically with multiple modems of
varying chipsets and seemingly irrespective of whether it's hardware or
software flow control... I'm wondering if this is a HylaFAX bug?

Attached are three logs.

c00002114 is Class 1 attempt with Conexant-chipset modem - failed
c00002116 is Class 2 attempt (same modem as c00002114) - failed
c00000006 is Class 2.0 attempt with USR 28.8 modem - successful
c00000007 is Class 1 attempt with USR 28.8 modem - successful

Any log-analyzing gurus out there?

Thanks.
Lee.

Feb 14 17:17:14.86: [30236]: SESSION BEGIN 00002114 18173581148
Feb 14 17:17:14.86: [30236]: SEND FAX: JOB 597 DEST 1817 358 1148 COMMID 00002114
Feb 14 17:17:14.86: [30236]: MODEM set DTR OFF
Feb 14 17:17:14.86: [30236]: DELAY 2600 ms
Feb 14 17:17:17.46: [30236]: MODEM set DTR ON
Feb 14 17:17:17.46: [30236]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Feb 14 17:17:17.46: [30236]: MODEM flush i/o
Feb 14 17:17:17.46: [30236]: <-- [4:ATZ\r]
Feb 14 17:17:17.59: [30236]: --> [2:OK]
Feb 14 17:17:17.59: [30236]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 14 17:17:17.60: [30236]: --> [14:ATE0V1Q0S0=0H0]
Feb 14 17:17:17.60: [30236]: --> [2:OK]
Feb 14 17:17:17.60: [30236]: <-- [21:ATS8=2S7=60&K3&D2&C1\r]
Feb 14 17:17:17.61: [30236]: --> [2:OK]
Feb 14 17:17:17.61: [30236]: <-- [12:AT+FCLASS=1\r]
Feb 14 17:17:17.62: [30236]: --> [2:OK]
Feb 14 17:17:17.62: [30236]: <-- [5:ATM0\r]
Feb 14 17:17:17.63: [30236]: --> [2:OK]
Feb 14 17:17:17.63: [30236]: STATE CHANGE: RUNNING -> SENDING
Feb 14 17:17:17.63: [30236]: MODEM input buffering enabled
Feb 14 17:17:17.63: [30236]: <-- [12:AT+FCLASS=1\r]
Feb 14 17:17:17.74: [30236]: --> [2:OK]
Feb 14 17:17:17.74: [30236]: DIAL 18173581148
Feb 14 17:17:17.74: [30236]: <-- [16:ATDT18173581148\r]
Feb 14 17:18:35.59: [30236]: --> [10:NO CARRIER]
Feb 14 17:18:35.59: [30236]: SEND FAILED: No carrier detected
Feb 14 17:18:35.59: [30236]: <-- [5:ATH0\r]
Feb 14 17:18:37.13: [30236]: --> [2:OK]
Feb 14 17:18:37.13: [30236]: MODEM set DTR OFF
Feb 14 17:18:37.13: [30236]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Feb 14 17:18:37.13: [30236]: SESSION END
Feb 14 17:27:23.01: [30772]: SESSION BEGIN 00002116 18173581148
Feb 14 17:27:23.01: [30772]: SEND FAX: JOB 598 DEST 1817 358 1148 COMMID 00002116
Feb 14 17:27:23.01: [30772]: MODEM set DTR OFF
Feb 14 17:27:23.01: [30772]: DELAY 2600 ms
Feb 14 17:27:25.61: [30772]: MODEM set DTR ON
Feb 14 17:27:25.61: [30772]: MODEM set baud rate: 38400 baud, input flow XON/XOFF, output flow XON/XOFF
Feb 14 17:27:25.61: [30772]: MODEM flush i/o
Feb 14 17:27:25.61: [30772]: <-- [4:ATZ\r]
Feb 14 17:27:25.74: [30772]: --> [2:OK]
Feb 14 17:27:25.74: [30772]: <-- [15:ATE0V1Q0S0=0H0\r]
Feb 14 17:27:25.75: [30772]: --> [14:ATE0V1Q0S0=0H0]
Feb 14 17:27:25.75: [30772]: --> [2:OK]
Feb 14 17:27:25.75: [30772]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Feb 14 17:27:25.77: [30772]: --> [2:OK]
Feb 14 17:27:25.77: [30772]: <-- [12:AT+FCLASS=2\r]
Feb 14 17:27:25.78: [30772]: --> [2:OK]
Feb 14 17:27:25.78: [30772]: <-- [10:AT+FTBC=0\r]
Feb 14 17:27:25.79: [30772]: --> [2:OK]
Feb 14 17:27:25.79: [30772]: <-- [10:AT+FBOR=0\r]
Feb 14 17:27:25.80: [30772]: --> [2:OK]
Feb 14 17:27:25.80: [30772]: <-- [13:AT+FPHCTO=30\r]
Feb 14 17:27:25.81: [30772]: --> [2:OK]
Feb 14 17:27:25.81: [30772]: <-- [3:AT\r]
Feb 14 17:27:25.82: [30772]: --> [2:OK]
Feb 14 17:27:25.82: [30772]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Feb 14 17:27:25.83: [30772]: --> [2:OK]
Feb 14 17:27:25.83: [30772]: <-- [5:ATM0\r]
Feb 14 17:27:25.84: [30772]: --> [2:OK]
Feb 14 17:27:25.84: [30772]: STATE CHANGE: RUNNING -> SENDING
Feb 14 17:27:25.84: [30772]: MODEM input buffering enabled
Feb 14 17:27:25.84: [30772]: <-- [12:AT+FCLASS=2\r]
Feb 14 17:27:25.95: [30772]: --> [2:OK]
Feb 14 17:27:25.95: [30772]: <-- [10:AT+FTBC=0\r]
Feb 14 17:27:26.06: [30772]: --> [2:OK]
Feb 14 17:27:26.06: [30772]: <-- [10:AT+FBOR=0\r]
Feb 14 17:27:26.17: [30772]: --> [2:OK]
Feb 14 17:27:26.17: [30772]: <-- [13:AT+FPHCTO=30\r]
Feb 14 17:27:26.28: [30772]: --> [2:OK]
Feb 14 17:27:26.28: [30772]: <-- [3:AT\r]
Feb 14 17:27:26.39: [30772]: --> [2:OK]
Feb 14 17:27:26.39: [30772]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Feb 14 17:27:26.50: [30772]: --> [2:OK]
Feb 14 17:27:26.50: [30772]: <-- [23:AT+FLID="Deanox, Inc."\r]
Feb 14 17:27:26.61: [30772]: --> [2:OK]
Feb 14 17:27:26.61: [30772]: DIAL 18173581148
Feb 14 17:27:26.61: [30772]: <-- [16:ATDT18173581148\r]
Feb 14 17:28:18.63: [30772]: --> [9:+FHNG: 11]
Feb 14 17:28:18.63: [30772]: REMOTE HANGUP: No answer (T.30 T1 timeout) (code 11)
Feb 14 17:28:18.63: [30772]: SEND FAILED: No answer (T.30 T1 timeout)
Feb 14 17:28:18.63: [30772]: <-- [5:ATH0\r]
Feb 14 17:28:20.06: [30772]: --> [2:OK]
Feb 14 17:28:20.06: [30772]: MODEM set DTR OFF
Feb 14 17:28:20.06: [30772]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Feb 14 17:28:20.06: [30772]: SESSION END
Feb 14 17:37:59.93: [ 1602]: SESSION BEGIN 00000006 18173581148
Feb 14 17:37:59.93: [ 1602]: SEND FAX: JOB 5 DEST 1817 358 1148 COMMID 00000006
Feb 14 17:37:59.93: [ 1602]: MODEM set DTR OFF
Feb 14 17:37:59.93: [ 1602]: DELAY 2600 ms
Feb 14 17:38:02.53: [ 1602]: MODEM set DTR ON
Feb 14 17:38:02.53: [ 1602]: MODEM set baud rate: 38400 baud, input flow RTS/CTS, output flow RTS/CTS
Feb 14 17:38:02.53: [ 1602]: MODEM flush i/o
Feb 14 17:38:02.53: [ 1602]: <-- [4:ATZ\r]
Feb 14 17:38:02.66: [ 1602]: --> [2:OK]
Feb 14 17:38:02.66: [ 1602]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Feb 14 17:38:02.80: [ 1602]: --> [16:ATE0V1Q0X4S0=0H0]
Feb 14 17:38:02.80: [ 1602]: --> [2:OK]
Feb 14 17:38:02.80: [ 1602]: <-- [32:ATS8=2S7=60&H1&I0&R2S13=1&D2&C1\r]
Feb 14 17:38:02.94: [ 1602]: --> [2:OK]
Feb 14 17:38:02.94: [ 1602]: <-- [14:AT+FCLASS=2.0\r]
Feb 14 17:38:03.07: [ 1602]: --> [2:OK]
Feb 14 17:38:03.07: [ 1602]: <-- [9:AT+FLO=2\r]
Feb 14 17:38:03.20: [ 1602]: --> [2:OK]
Feb 14 17:38:03.20: [ 1602]: <-- [9:AT+FPP=0\r]
Feb 14 17:38:03.33: [ 1602]: --> [2:OK]
Feb 14 17:38:03.33: [ 1602]: <-- [9:AT+FBO=0\r]
Feb 14 17:38:03.46: [ 1602]: --> [2:OK]
Feb 14 17:38:03.46: [ 1602]: <-- [10:AT+FCT=30\r]
Feb 14 17:38:03.60: [ 1602]: --> [2:OK]
Feb 14 17:38:03.60: [ 1602]: <-- [15:AT+FNR=1,1,1,0\r]
Feb 14 17:38:03.74: [ 1602]: --> [2:OK]
Feb 14 17:38:03.74: [ 1602]: <-- [9:AT+FIE=0\r]
Feb 14 17:38:03.87: [ 1602]: --> [2:OK]
Feb 14 17:38:03.87: [ 1602]: <-- [9:AT+FBU=0\r]
Feb 14 17:38:04.00: [ 1602]: --> [2:OK]
Feb 14 17:38:04.00: [ 1602]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Feb 14 17:38:04.14: [ 1602]: --> [2:OK]
Feb 14 17:38:04.14: [ 1602]: <-- [5:ATM0\r]
Feb 14 17:38:04.27: [ 1602]: --> [2:OK]
Feb 14 17:38:04.27: [ 1602]: STATE CHANGE: RUNNING -> SENDING
Feb 14 17:38:04.27: [ 1602]: MODEM input buffering enabled
Feb 14 17:38:04.27: [ 1602]: <-- [14:AT+FCLASS=2.0\r]
Feb 14 17:38:04.51: [ 1602]: --> [2:OK]
Feb 14 17:38:04.51: [ 1602]: <-- [9:AT+FLO=2\r]
Feb 14 17:38:04.74: [ 1602]: --> [2:OK]
Feb 14 17:38:04.74: [ 1602]: <-- [9:AT+FPP=0\r]
Feb 14 17:38:04.97: [ 1602]: --> [2:OK]
Feb 14 17:38:04.97: [ 1602]: <-- [9:AT+FBO=0\r]
Feb 14 17:38:05.20: [ 1602]: --> [2:OK]
Feb 14 17:38:05.20: [ 1602]: <-- [10:AT+FCT=30\r]
Feb 14 17:38:05.44: [ 1602]: --> [2:OK]
Feb 14 17:38:05.44: [ 1602]: <-- [15:AT+FNR=1,1,1,0\r]
Feb 14 17:38:05.68: [ 1602]: --> [2:OK]
Feb 14 17:38:05.68: [ 1602]: <-- [9:AT+FIE=0\r]
Feb 14 17:38:05.91: [ 1602]: --> [2:OK]
Feb 14 17:38:05.91: [ 1602]: <-- [9:AT+FBU=0\r]
Feb 14 17:38:06.14: [ 1602]: --> [2:OK]
Feb 14 17:38:06.14: [ 1602]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Feb 14 17:38:06.38: [ 1602]: --> [2:OK]
Feb 14 17:38:06.38: [ 1602]: <-- [22:AT+FLI="Deanox, Inc."\r]
Feb 14 17:38:06.62: [ 1602]: --> [2:OK]
Feb 14 17:38:06.62: [ 1602]: DIAL 18173581148
Feb 14 17:38:06.62: [ 1602]: <-- [16:ATDT18173581148\r]
Feb 14 17:38:22.46: [ 1602]: --> [4:+FCO]
Feb 14 17:38:24.59: [ 1602]: --> [27:+FCI:"                    "]
Feb 14 17:38:24.59: [ 1602]: REMOTE CSI ""
Feb 14 17:38:24.59: [ 1602]: --> [20:+FIS:1,5,0,2,1,0,0,0]
Feb 14 17:38:24.59: [ 1602]: --> [2:OK]
Feb 14 17:38:24.59: [ 1602]: REMOTE best rate 14400 bit/s
Feb 14 17:38:24.59: [ 1602]: REMOTE max page width 1728 pixels in 215 mm
Feb 14 17:38:24.59: [ 1602]: REMOTE max unlimited page length
Feb 14 17:38:24.59: [ 1602]: REMOTE best vres 7.7 line/mm
Feb 14 17:38:24.59: [ 1602]: REMOTE best format 2-D MR
Feb 14 17:38:24.59: [ 1602]: REMOTE best 0 ms/scanline
Feb 14 17:38:24.59: [ 1602]: USE 14400 bit/s
Feb 14 17:38:24.59: [ 1602]: USE 0 ms/scanline
Feb 14 17:38:24.59: [ 1602]: SEND file "docq/doc5.cover;01"
Feb 14 17:38:24.59: [ 1602]: USE page width 1728 pixels in 215 mm
Feb 14 17:38:24.59: [ 1602]: USE unlimited page length
Feb 14 17:38:24.59: [ 1602]: USE 7.7 line/mm
Feb 14 17:38:24.59: [ 1602]: USE 1-D MR
Feb 14 17:38:24.59: [ 1602]: <-- [23:AT+FIS=1,5,0,2,0,0,0,0\r]
Feb 14 17:38:24.83: [ 1602]: --> [2:OK]
Feb 14 17:38:24.83: [ 1602]: <-- [7:AT+FDT\r]
Feb 14 17:38:25.14: [ 1602]: --> [20:+FCS:1,5,0,2,0,0,0,0]
Feb 14 17:38:32.09: [ 1602]: --> [7:CONNECT]
Feb 14 17:38:32.09: [ 1602]: SEND begin page
Feb 14 17:38:32.09: [ 1602]: <-- data [1025]
Feb 14 17:38:32.09: [ 1602]: <-- data [1026]
Feb 14 17:38:32.09: [ 1602]: <-- data [1028]
Feb 14 17:38:32.09: [ 1602]: <-- data [1028]
Feb 14 17:38:32.09: [ 1602]: <-- data [1029]
Feb 14 17:38:33.09: [ 1602]: <-- data [1028]
Feb 14 17:38:33.09: [ 1602]: <-- data [1027]
Feb 14 17:38:33.09: [ 1602]: <-- data [1025]
Feb 14 17:38:34.15: [ 1602]: <-- data [1028]
Feb 14 17:38:34.15: [ 1602]: <-- data [1027]
Feb 14 17:38:35.05: [ 1602]: <-- data [1024]
Feb 14 17:38:35.05: [ 1602]: <-- data [1026]
Feb 14 17:38:35.95: [ 1602]: <-- data [1024]
Feb 14 17:38:35.95: [ 1602]: <-- data [1024]
Feb 14 17:38:36.85: [ 1602]: <-- data [1030]
Feb 14 17:38:37.75: [ 1602]: <-- data [1028]
Feb 14 17:38:37.75: [ 1602]: <-- data [1030]
Feb 14 17:38:38.65: [ 1602]: <-- data [1024]
Feb 14 17:38:39.55: [ 1602]: <-- data [1029]
Feb 14 17:38:39.55: [ 1602]: <-- data [1025]
Feb 14 17:38:40.45: [ 1602]: <-- data [1031]
Feb 14 17:38:40.45: [ 1602]: <-- data [1029]
Feb 14 17:38:41.35: [ 1602]: <-- data [1025]
Feb 14 17:38:42.25: [ 1602]: <-- data [1029]
Feb 14 17:38:42.25: [ 1602]: <-- data [1034]
Feb 14 17:38:43.15: [ 1602]: <-- data [1028]
Feb 14 17:38:44.05: [ 1602]: <-- data [950]
Feb 14 17:38:44.05: [ 1602]: SENT 27561 bytes of data
Feb 14 17:38:44.05: [ 1602]: SEND 1D RTC
Feb 14 17:38:44.05: [ 1602]: <-- data [9]
Feb 14 17:38:44.05: [ 1602]: SEND end page
Feb 14 17:38:44.05: [ 1602]: SEND send MPS (more pages, same document)
Feb 14 17:38:44.05: [ 1602]: <-- data [2]
Feb 14 17:38:50.25: [ 1602]: --> [2:OK]
Feb 14 17:38:50.25: [ 1602]: <-- [8:AT+FPS?\r]
Feb 14 17:38:50.48: [ 1602]: --> [1:1]
Feb 14 17:38:50.61: [ 1602]: --> [2:OK]
Feb 14 17:38:50.61: [ 1602]: SEND recv MCF (message confirmation)
Feb 14 17:38:50.61: [ 1602]: SEND FAX (00000006): FROM lee@deanox.com TO 1817 358 1148 (page 1 of 2 sent in 0:26)
Feb 14 17:38:50.61: [ 1602]: SEND FAX (00000006): FROM lee@deanox.com TO 1817 358 1148 (docq/doc5.cover;01 sent in 0:26)
Feb 14 17:38:50.61: [ 1602]: SEND file "docq/doc12.tif;01"
Feb 14 17:38:50.61: [ 1602]: USE page width 1728 pixels in 215 mm
Feb 14 17:38:50.61: [ 1602]: USE unlimited page length
Feb 14 17:38:50.61: [ 1602]: USE 7.7 line/mm
Feb 14 17:38:50.61: [ 1602]: USE 1-D MR
Feb 14 17:38:50.61: [ 1602]: <-- [7:AT+FDT\r]
Feb 14 17:38:51.05: [ 1602]: --> [7:CONNECT]
Feb 14 17:38:51.05: [ 1602]: SEND begin page
Feb 14 17:38:51.05: [ 1602]: <-- data [1026]
Feb 14 17:38:51.05: [ 1602]: <-- data [1033]
Feb 14 17:38:51.05: [ 1602]: <-- data [1035]
Feb 14 17:38:51.05: [ 1602]: <-- data [1031]
Feb 14 17:38:51.05: [ 1602]: <-- data [1038]
Feb 14 17:38:52.05: [ 1602]: <-- data [1026]
Feb 14 17:38:52.05: [ 1602]: <-- data [1036]
Feb 14 17:38:52.05: [ 1602]: <-- data [1028]
Feb 14 17:38:53.11: [ 1602]: <-- data [1029]
Feb 14 17:38:53.11: [ 1602]: <-- data [1029]
Feb 14 17:38:54.01: [ 1602]: <-- data [1028]
Feb 14 17:38:54.01: [ 1602]: <-- data [1036]
Feb 14 17:38:54.91: [ 1602]: <-- data [1030]
Feb 14 17:38:54.91: [ 1602]: <-- data [1033]
Feb 14 17:38:55.81: [ 1602]: <-- data [1032]
Feb 14 17:38:56.71: [ 1602]: <-- data [1026]
Feb 14 17:38:56.71: [ 1602]: <-- data [1026]
Feb 14 17:38:57.61: [ 1602]: <-- data [1029]
Feb 14 17:38:58.51: [ 1602]: <-- data [1026]
Feb 14 17:38:58.51: [ 1602]: <-- data [622]
Feb 14 17:38:59.41: [ 1602]: SENT 20072 bytes of data
Feb 14 17:38:59.41: [ 1602]: SEND 1D RTC
Feb 14 17:38:59.41: [ 1602]: <-- data [9]
Feb 14 17:38:59.41: [ 1602]: SEND end page
Feb 14 17:38:59.41: [ 1602]: SEND send EOP (no more pages or documents)
Feb 14 17:38:59.41: [ 1602]: <-- data [2]
Feb 14 17:39:06.46: [ 1602]: --> [7:+FHS:00]
Feb 14 17:39:06.46: [ 1602]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Feb 14 17:39:06.46: [ 1602]: SEND recv MCF (message confirmation)
Feb 14 17:39:06.46: [ 1602]: SEND FAX (00000006): FROM lee@deanox.com TO 1817 358 1148 (page 2 of 2 sent in 0:16)
Feb 14 17:39:06.46: [ 1602]: SEND FAX (00000006): FROM lee@deanox.com TO 1817 358 1148 (docq/doc12.tif;01 sent in 0:16)
Feb 14 17:39:06.46: [ 1602]: <-- [5:ATH0\r]
Feb 14 17:39:06.59: [ 1602]: --> [2:OK]
Feb 14 17:39:06.59: [ 1602]: MODEM set DTR OFF
Feb 14 17:39:06.59: [ 1602]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Feb 14 17:39:06.59: [ 1602]: SESSION END
Feb 14 18:02:15.83: [ 1993]: SESSION BEGIN 00000007 18173581148
Feb 14 18:02:15.83: [ 1993]: SEND FAX: JOB 6 DEST 1817 358 1148 COMMID 00000007
Feb 14 18:02:15.83: [ 1993]: MODEM set DTR OFF
Feb 14 18:02:15.83: [ 1993]: DELAY 2600 ms
Feb 14 18:02:18.43: [ 1993]: MODEM set DTR ON
Feb 14 18:02:18.43: [ 1993]: MODEM set baud rate: 38400 baud, input flow XON/XOFF, output flow XON/XOFF
Feb 14 18:02:18.43: [ 1993]: MODEM flush i/o
Feb 14 18:02:18.43: [ 1993]: <-- [4:ATZ\r]
Feb 14 18:02:18.56: [ 1993]: --> [2:OK]
Feb 14 18:02:18.56: [ 1993]: <-- [17:ATE0V1Q0X4S0=0H0\r]
Feb 14 18:02:18.70: [ 1993]: --> [16:ATE0V1Q0X4S0=0H0]
Feb 14 18:02:18.70: [ 1993]: --> [2:OK]
Feb 14 18:02:18.70: [ 1993]: <-- [32:ATS8=2S7=60&H2&I2&R1S13=1&D2&C1\r]
Feb 14 18:02:18.84: [ 1993]: --> [2:OK]
Feb 14 18:02:18.84: [ 1993]: <-- [12:AT+FCLASS=1\r]
Feb 14 18:02:18.97: [ 1993]: --> [2:OK]
Feb 14 18:02:18.97: [ 1993]: <-- [12:AT+FCLASS=0\r]
Feb 14 18:02:19.10: [ 1993]: --> [2:OK]
Feb 14 18:02:19.10: [ 1993]: <-- [5:ATM0\r]
Feb 14 18:02:19.23: [ 1993]: --> [2:OK]
Feb 14 18:02:19.23: [ 1993]: STATE CHANGE: RUNNING -> SENDING
Feb 14 18:02:19.23: [ 1993]: MODEM input buffering enabled
Feb 14 18:02:19.23: [ 1993]: <-- [12:AT+FCLASS=1\r]
Feb 14 18:02:19.47: [ 1993]: --> [2:OK]
Feb 14 18:02:19.47: [ 1993]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Feb 14 18:02:19.47: [ 1993]: DIAL 18173581148
Feb 14 18:02:19.47: [ 1993]: <-- [16:ATDT18173581148\r]
Feb 14 18:02:35.91: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:35.91: [ 1993]: MODEM input buffering disabled
Feb 14 18:02:37.17: [ 1993]: --> HDLC<25:FF C0 02 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 A4 F3>
Feb 14 18:02:37.17: [ 1993]: --> [2:OK]
Feb 14 18:02:37.17: [ 1993]: REMOTE CSI ""
Feb 14 18:02:37.17: [ 1993]: <-- [9:AT+FRH=3\r]
Feb 14 18:02:37.18: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:37.55: [ 1993]: --> HDLC<9:FF C8 01 00 77 1F 22 F8 96>
Feb 14 18:02:37.55: [ 1993]: --> [2:OK]
Feb 14 18:02:37.55: [ 1993]: REMOTE best rate 14400 bit/s
Feb 14 18:02:37.55: [ 1993]: REMOTE max page width 1728 pixels in 215 mm
Feb 14 18:02:37.55: [ 1993]: REMOTE max unlimited page length
Feb 14 18:02:37.55: [ 1993]: REMOTE best vres 7.7 line/mm
Feb 14 18:02:37.55: [ 1993]: REMOTE best format 2-D MMR
Feb 14 18:02:37.55: [ 1993]: REMOTE supports T.30 Annex A, ECM
Feb 14 18:02:37.55: [ 1993]: REMOTE best 0 ms/scanline
Feb 14 18:02:37.55: [ 1993]: USE 14400 bit/s
Feb 14 18:02:37.55: [ 1993]: USE 0 ms/scanline
Feb 14 18:02:37.55: [ 1993]: SEND file "docq/doc6.cover;41"
Feb 14 18:02:37.55: [ 1993]: USE page width 1728 pixels in 215 mm
Feb 14 18:02:37.55: [ 1993]: USE unlimited page length
Feb 14 18:02:37.55: [ 1993]: USE 7.7 line/mm
Feb 14 18:02:37.55: [ 1993]: USE 2-D MR
Feb 14 18:02:37.55: [ 1993]: SEND training at v.17 14400 bit/s
Feb 14 18:02:37.55: [ 1993]: <-- [9:AT+FTH=3\r]
Feb 14 18:02:37.79: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:37.79: [ 1993]: <-- HDLC<23:FF C0 C2 74 C6 76 92 04 34 1E F6 76 86 A6 22 04 04 04 04 04 04 04 04>
Feb 14 18:02:37.79: [ 1993]: <-- data [23]
Feb 14 18:02:37.79: [ 1993]: <-- data [2]
Feb 14 18:02:37.81: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:37.81: [ 1993]: <-- HDLC<6:FF C8 C1 00 47 1E>
Feb 14 18:02:37.81: [ 1993]: <-- data [6]
Feb 14 18:02:37.81: [ 1993]: <-- data [2]
Feb 14 18:02:39.76: [ 1993]: --> [2:OK]
Feb 14 18:02:39.76: [ 1993]: DELAY 75 ms
Feb 14 18:02:39.84: [ 1993]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Feb 14 18:02:39.84: [ 1993]: <-- [11:AT+FTM=145\r]
Feb 14 18:02:41.32: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:41.32: [ 1993]: <-- data [1024]
Feb 14 18:02:41.32: [ 1993]: <-- data [1024]
Feb 14 18:02:41.32: [ 1993]: <-- data [652]
Feb 14 18:02:41.32: [ 1993]: <-- data [2]
Feb 14 18:02:42.84: [ 1993]: --> [2:OK]
Feb 14 18:02:42.84: [ 1993]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Feb 14 18:02:42.84: [ 1993]: <-- [9:AT+FRH=3\r]
Feb 14 18:02:43.46: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:44.45: [ 1993]: --> HDLC<5:FF C8 21 57 BE>
Feb 14 18:02:44.46: [ 1993]: --> [2:OK]
Feb 14 18:02:44.46: [ 1993]: TRAINING succeeded
Feb 14 18:02:44.46: [ 1993]: <-- [11:AT+FTM=146\r]
Feb 14 18:02:44.80: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:44.80: [ 1993]: SEND begin page
Feb 14 18:02:44.80: [ 1993]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Feb 14 18:02:44.80: [ 1993]: <-- data [1031]
Feb 14 18:02:44.80: [ 1993]: <-- data [1029]
Feb 14 18:02:44.80: [ 1993]: <-- data [1027]
Feb 14 18:02:44.80: [ 1993]: <-- data [1032]
Feb 14 18:02:44.80: [ 1993]: <-- data [1043]
Feb 14 18:02:45.80: [ 1993]: <-- data [1049]
Feb 14 18:02:45.80: [ 1993]: <-- data [1040]
Feb 14 18:02:45.80: [ 1993]: <-- data [1043]
Feb 14 18:02:46.90: [ 1993]: <-- data [1038]
Feb 14 18:02:46.90: [ 1993]: <-- data [1038]
Feb 14 18:02:47.87: [ 1993]: <-- data [1033]
Feb 14 18:02:47.87: [ 1993]: <-- data [1031]
Feb 14 18:02:48.84: [ 1993]: <-- data [1041]
Feb 14 18:02:48.84: [ 1993]: <-- data [1030]
Feb 14 18:02:49.77: [ 1993]: <-- data [1033]
Feb 14 18:02:49.77: [ 1993]: <-- data [1038]
Feb 14 18:02:50.70: [ 1993]: <-- data [1039]
Feb 14 18:02:51.64: [ 1993]: <-- data [1028]
Feb 14 18:02:51.64: [ 1993]: <-- data [1033]
Feb 14 18:02:52.57: [ 1993]: <-- data [880]
Feb 14 18:02:52.57: [ 1993]: SENT 20329 bytes of data
Feb 14 18:02:52.57: [ 1993]: SEND 2D RTC
Feb 14 18:02:52.57: [ 1993]: <-- data [30]
Feb 14 18:02:52.57: [ 1993]: <-- data [2]
Feb 14 18:02:52.57: [ 1993]: SEND end page
Feb 14 18:02:56.13: [ 1993]: --> [2:OK]
Feb 14 18:02:56.13: [ 1993]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Feb 14 18:02:56.13: [ 1993]: DELAY 75 ms
Feb 14 18:02:56.21: [ 1993]: SEND send MPS (more pages, same document)
Feb 14 18:02:56.21: [ 1993]: <-- [9:AT+FTH=3\r]
Feb 14 18:02:56.36: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:56.36: [ 1993]: <-- HDLC<3:FF C8 F2>
Feb 14 18:02:56.36: [ 1993]: <-- data [3]
Feb 14 18:02:56.36: [ 1993]: <-- data [2]
Feb 14 18:02:57.54: [ 1993]: --> [2:OK]
Feb 14 18:02:57.54: [ 1993]: <-- [9:AT+FRH=3\r]
Feb 14 18:02:57.86: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:58.96: [ 1993]: --> HDLC<5:FF C8 31 45 8F>
Feb 14 18:02:58.96: [ 1993]: --> [2:OK]
Feb 14 18:02:58.96: [ 1993]: SEND recv MCF (message confirmation)
Feb 14 18:02:58.96: [ 1993]: SEND FAX (00000007): FROM lee@deanox.com TO 1817 358 1148 (page 1 of 2 sent in 0:21)
Feb 14 18:02:58.96: [ 1993]: SEND FAX (00000007): FROM lee@deanox.com TO 1817 358 1148 (docq/doc6.cover;41 sent in 0:21)
Feb 14 18:02:58.96: [ 1993]: SEND file "docq/doc14.tif;41"
Feb 14 18:02:58.96: [ 1993]: USE page width 1728 pixels in 215 mm
Feb 14 18:02:58.96: [ 1993]: USE unlimited page length
Feb 14 18:02:58.96: [ 1993]: USE 7.7 line/mm
Feb 14 18:02:58.96: [ 1993]: USE 2-D MR
Feb 14 18:02:58.97: [ 1993]: <-- [11:AT+FTM=146\r]
Feb 14 18:02:59.30: [ 1993]: --> [7:CONNECT]
Feb 14 18:02:59.30: [ 1993]: SEND begin page
Feb 14 18:02:59.30: [ 1993]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Feb 14 18:02:59.30: [ 1993]: <-- data [1030]
Feb 14 18:02:59.30: [ 1993]: <-- data [1031]
Feb 14 18:02:59.30: [ 1993]: <-- data [1030]
Feb 14 18:02:59.30: [ 1993]: <-- data [1032]
Feb 14 18:02:59.30: [ 1993]: <-- data [1041]
Feb 14 18:03:00.30: [ 1993]: <-- data [1032]
Feb 14 18:03:00.30: [ 1993]: <-- data [1032]
Feb 14 18:03:00.30: [ 1993]: <-- data [1030]
Feb 14 18:03:01.36: [ 1993]: <-- data [1042]
Feb 14 18:03:01.36: [ 1993]: <-- data [1041]
Feb 14 18:03:02.26: [ 1993]: <-- data [1031]
Feb 14 18:03:02.26: [ 1993]: <-- data [1030]
Feb 14 18:03:03.16: [ 1993]: <-- data [1036]
Feb 14 18:03:03.16: [ 1993]: <-- data [145]
Feb 14 18:03:04.09: [ 1993]: SENT 13454 bytes of data
Feb 14 18:03:04.09: [ 1993]: SEND 2D RTC
Feb 14 18:03:04.09: [ 1993]: <-- data [30]
Feb 14 18:03:04.09: [ 1993]: <-- data [2]
Feb 14 18:03:04.09: [ 1993]: SEND end page
Feb 14 18:03:06.82: [ 1993]: --> [2:OK]
Feb 14 18:03:06.82: [ 1993]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Feb 14 18:03:06.82: [ 1993]: DELAY 95 ms
Feb 14 18:03:06.92: [ 1993]: SEND send EOP (no more pages or documents)
Feb 14 18:03:06.92: [ 1993]: <-- [9:AT+FTH=3\r]
Feb 14 18:03:07.07: [ 1993]: --> [7:CONNECT]
Feb 14 18:03:07.07: [ 1993]: <-- HDLC<3:FF C8 F4>
Feb 14 18:03:07.07: [ 1993]: <-- data [3]
Feb 14 18:03:07.07: [ 1993]: <-- data [2]
Feb 14 18:03:08.25: [ 1993]: --> [2:OK]
Feb 14 18:03:08.25: [ 1993]: <-- [9:AT+FRH=3\r]
Feb 14 18:03:08.61: [ 1993]: --> [7:CONNECT]
Feb 14 18:03:09.67: [ 1993]: --> HDLC<5:FF C8 31 45 8F>
Feb 14 18:03:09.67: [ 1993]: --> [2:OK]
Feb 14 18:03:09.67: [ 1993]: SEND recv MCF (message confirmation)
Feb 14 18:03:09.67: [ 1993]: SEND FAX (00000007): FROM lee@deanox.com TO 1817 358 1148 (page 2 of 2 sent in 0:11)
Feb 14 18:03:09.67: [ 1993]: SEND FAX (00000007): FROM lee@deanox.com TO 1817 358 1148 (docq/doc14.tif;41 sent in 0:11)
Feb 14 18:03:09.67: [ 1993]: <-- [9:AT+FTH=3\r]
Feb 14 18:03:09.91: [ 1993]: --> [7:CONNECT]
Feb 14 18:03:09.91: [ 1993]: <-- HDLC<3:FF C8 DF>
Feb 14 18:03:09.91: [ 1993]: <-- data [3]
Feb 14 18:03:09.91: [ 1993]: <-- data [2]
Feb 14 18:03:11.08: [ 1993]: --> [2:OK]
Feb 14 18:03:11.08: [ 1993]: MODEM input buffering enabled
Feb 14 18:03:11.08: [ 1993]: <-- [5:ATH0\r]
Feb 14 18:03:11.31: [ 1993]: --> [2:OK]
Feb 14 18:03:11.31: [ 1993]: MODEM set DTR OFF
Feb 14 18:03:11.31: [ 1993]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Feb 14 18:03:11.31: [ 1993]: SESSION END