[hylafax-users] Problem with Class 2 fax and inbound fax's

["Peter Nunn" <pncomp@iprimus.com.au>]

Hi folks, I have just tried installing a new class 2 fax on my system and
have run into problems receiving a fax...

I had it all working with a class 1 but that got blown up by a thunder
storm, so I upgraded to a later model that is class 2.

I ran setup and config and all seemed to be OK.

When I ring in I get an answer OK and the software reports a correct send
(the other end that is), but when I check for the fax, nothing..

Here is the log.

Feb 05 12:15:49.55: [  806]: SESSION BEGIN 00000050 61397556954
Feb 05 12:15:49.56: [  806]: <-- [4:ATA\r]
Feb 05 12:15:51.59: [  806]: --> [3:FAX]
Feb 05 12:16:02.54: [  806]: --> [5:+FCON]
Feb 05 12:16:02.54: [  806]: ANSWER: FAX CONNECTION
Feb 05 12:16:02.54: [  806]: RECV FAX: begin
Feb 05 12:16:04.13: [  806]: --> [29:+FTSI: "        03 9819 9975"]
Feb 05 12:16:04.13: [  806]: REMOTE TSI "03 9819 9975"
Feb 05 12:16:04.48: [  806]: --> [22:+FDCS: 0,3,0,2,0,0,0,5]
Feb 05 12:16:04.48: [  806]: REMOTE wants 9600 bit/s
Feb 05 12:16:04.48: [  806]: REMOTE wants page width 1728 pixels in 215 mm
Feb 05 12:16:04.48: [  806]: REMOTE wants unlimited page length
Feb 05 12:16:04.48: [  806]: REMOTE wants 3.85 line/mm
Feb 05 12:16:04.48: [  806]: REMOTE wants 1-D MR
Feb 05 12:16:04.59: [  806]: --> [2:OK]
Feb 05 12:16:04.59: [  806]: <-- [7:AT+FDR\r]
Feb 05 12:16:06.13: [  806]: --> [5:+FCFR]
Feb 05 12:16:08.34: [  806]: --> [22:+FDCS: 0,3,0,2,0,0,0,5]
Feb 05 12:16:08.34: [  806]: REMOTE wants 9600 bit/s
Feb 05 12:16:08.34: [  806]: REMOTE wants page width 1728 pixels in 215 mm
Feb 05 12:16:08.34: [  806]: REMOTE wants unlimited page length
Feb 05 12:16:08.34: [  806]: REMOTE wants 3.85 line/mm
Feb 05 12:16:08.34: [  806]: REMOTE wants 1-D MR
Feb 05 12:16:08.34: [  806]: --> [7:CONNECT]
Feb 05 12:16:08.34: [  806]: RECV: begin page
Feb 05 12:16:08.35: [  806]: RECV: send trigger 022
Feb 05 12:16:08.35: [  806]: <-- data [1]
Feb 05 12:16:39.28: [  806]: RECV: 1482 total lines, 650 bad lines, 17
consecutive bad lines
Feb 05 12:16:39.29: [  806]: --> [17:+FPTS: 1,2219,0,0]
Feb 05 12:16:40.56: [  806]: --> [7:+FET: 2]
Feb 05 12:16:40.56: [  806]: RECV recv EOP (no more pages or documents)
Feb 05 12:16:40.67: [  806]: --> [2:OK]
Feb 05 12:16:40.67: [  806]: RECV: REJECT page quality, 56% good lines (95%
required)
Feb 05 12:16:40.67: [  806]: RECV send RTN (retrain negative)
Feb 05 12:16:40.67: [  806]: <-- [10:AT+FPTS=2\r]
Feb 05 12:16:40.78: [  806]: --> [2:OK]
Feb 05 12:16:40.78: [  806]: <-- [7:AT+FDR\r]
Feb 05 12:16:43.56: [  806]: --> [8:+FHNG: 0]
Feb 05 12:16:43.56: [  806]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Feb 05 12:16:43.57: [  806]: RECV FAX (00000050): recvq/fax00005.tif from 03
9819 9975, route to <unspecified>, 0 pages in 0:41
Feb 05 12:16:43.57: [  806]: RECV FAX: Normal and proper end of connection
Feb 05 12:16:43.57: [  806]: RECV FAX (00000050): session with 03 9819 9975
terminated abnormally: Normal and proper end of connection
Feb 05 12:16:43.57: [  806]: RECV FAX: bin/faxrcvd "recvq/fax00005.tif"
"ttyS1" "00000050" "Normal and proper end of connection"
Feb 05 12:16:43.83: [  806]: RECV FAX: end
Feb 05 12:16:43.83: [  806]: SESSION END

Any ideas what is going on here.   There is nothing in bin/faxrcvd either.

Thanks.

Peter



BEGIN:VCARD
VERSION:2.1
N:Nunn;Peter
FN:Peter Nunn
ORG:PN Computing
TEL;WORK;VOICE:(03) 9755-6950
TEL;WORK;VOICE:0412 174 230
TEL;HOME;VOICE:(03) 9755-6950
TEL;CELL;VOICE:0412 174 230
TEL;WORK;FAX:(03) 9755-6954
ADR;WORK:;;13 Koombahla Crt;Rowville;Vic;3178;Australia
LABEL;WORK;ENCODING=QUOTED-PRINTABLE:13 Koombahla Crt=0D=0ARowville, Vic 3178=0D=0AAustralia
ADR;HOME:;;10 Walsh Ave;Scoresby;Vic;3178;Australia
LABEL;HOME;ENCODING=QUOTED-PRINTABLE:10 Walsh Ave=0D=0AScoresby, Vic 3178=0D=0AAustralia
URL:
URL:http://www.pncomputing.com
EMAIL;PREF;INTERNET:pnunn@pncomputing.com
EMAIL;INTERNET:pnunn@melbpc.org.au
REV:20010105T032645Z
END:VCARD