[hylafax-users] newbie questions

["Eric Wood" <eric@interplas.com>]

Hello,
I'm struggling over a couple of things:

1. I sent a test fax using "sendfax -n -d 2977186 /etc/passwd/" and I'm
using a generic class 2.0 config file, generic modem, RH 7.0:

After the dial command, I get funky FNF and DNF characters from the remote
fax machine.  Is this normal?
Also, the first few lines of the /etc/passwd file come out okay but the
remainer of the page is "squished" and unreadable.  Is it possible
that the the graphics conversion utilities are not compatiable for Hylafax
and RH 7.0?

Thanks,
-eric wood


Mar 08 12:44:47.12: [ 8445]: SESSION BEGIN 00000010 18642977186
Mar 08 12:44:47.13: [ 8445]: SEND FAX: JOB 9 DEST 2977186 COMMID 00000010
Mar 08 12:44:47.13: [ 8445]: DELAY 2600 ms
Mar 08 12:44:49.72: [ 8445]: <-- [4:ATZ\r]
Mar 08 12:44:49.86: [ 8445]: --> [2:OK]
Mar 08 12:44:49.86: [ 8445]: <-- [15:ATE0V1Q0S0=0H0\r]
Mar 08 12:44:50.00: [ 8445]: --> [14:ATE0V1Q0S0=0H0]
Mar 08 12:44:50.00: [ 8445]: --> [2:OK]
Mar 08 12:44:50.00: [ 8445]: <-- [12:ATS8=2S7=60\r]
Mar 08 12:44:50.14: [ 8445]: --> [2:OK]
Mar 08 12:44:50.14: [ 8445]: <-- [14:AT+FCLASS=2.0\r]
Mar 08 12:44:50.28: [ 8445]: --> [2:OK]
Mar 08 12:44:50.28: [ 8445]: <-- [9:AT+FLO=0\r]
Mar 08 12:44:50.42: [ 8445]: --> [2:OK]
Mar 08 12:44:50.42: [ 8445]: <-- [9:AT+FPP=0\r]
Mar 08 12:44:50.56: [ 8445]: --> [2:OK]
Mar 08 12:44:50.56: [ 8445]: <-- [9:AT+FBO=0\r]
Mar 08 12:44:50.70: [ 8445]: --> [2:OK]
Mar 08 12:44:50.70: [ 8445]: <-- [10:AT+FCT=30\r]
Mar 08 12:44:50.84: [ 8445]: --> [2:OK]
Mar 08 12:44:50.84: [ 8445]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 08 12:44:50.98: [ 8445]: --> [2:OK]
Mar 08 12:44:50.98: [ 8445]: <-- [9:AT+FIE=0\r]
Mar 08 12:44:51.12: [ 8445]: --> [2:OK]
Mar 08 12:44:51.12: [ 8445]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]Mar 08
12:44:51.26: [ 8445]: --> [2:OK]
Mar 08 12:44:51.26: [ 8445]: <-- [5:ATM0\r]
Mar 08 12:44:51.39: [ 8445]: --> [2:OK]
Mar 08 12:44:51.39: [ 8445]: <-- [14:AT+FCLASS=2.0\r]
Mar 08 12:44:51.63: [ 8445]: --> [2:OK]
Mar 08 12:44:51.63: [ 8445]: <-- [9:AT+FLO=0\r]
Mar 08 12:44:51.87: [ 8445]: --> [2:OK]
Mar 08 12:44:51.87: [ 8445]: <-- [9:AT+FPP=0\r]
Mar 08 12:44:52.11: [ 8445]: --> [2:OK]
Mar 08 12:44:52.11: [ 8445]: <-- [9:AT+FBO=0\r]
Mar 08 12:44:52.35: [ 8445]: --> [2:OK]
Mar 08 12:44:52.35: [ 8445]: <-- [10:AT+FCT=30\r]
Mar 08 12:44:52.59: [ 8445]: --> [2:OK]
Mar 08 12:44:52.59: [ 8445]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 08 12:44:52.83: [ 8445]: --> [2:OK]
Mar 08 12:44:52.83: [ 8445]: <-- [9:AT+FIE=0\r]
Mar 08 12:44:53.07: [ 8445]: --> [2:OK]
Mar 08 12:44:53.07: [ 8445]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
Mar 08 12:44:53.31: [ 8445]: --> [2:OK]
Mar 08 12:44:53.31: [ 8445]: <-- [19:AT+FLI="InterPlas"\r]
Mar 08 12:44:53.55: [ 8445]: --> [2:OK]
Mar 08 12:44:53.55: [ 8445]: DIAL 2977186
Mar 08 12:44:53.55: [ 8445]: <-- [14:ATDT92977186@\r]
Mar 08 12:45:09.09: [ 8445]: --> [4:+FCO]
Mar 08 12:45:10.94: [ 8445]: --> [15:+FNF:%ÿþ<92>^PM^BX*,]
Mar 08 12:45:10.94: [ 8445]: REMOTE NSF "%ÿþ<92>^PM^BX*,"
Mar 08 12:45:10.94: [ 8445]: NSF remote fax equipment: unknown
Mar 08 12:45:10.94: [ 8445]: --> [20:+FIS:1,5,2,2,1,0,0,2]
Mar 08 12:45:10.94: [ 8445]: --> [2:OK]
Mar 08 12:45:10.94: [ 8445]: REMOTE best rate 14400 bit/s
Mar 08 12:45:10.94: [ 8445]: REMOTE max page width 2432 pixels in 303 mm
Mar 08 12:45:10.94: [ 8445]: REMOTE max unlimited page length
Mar 08 12:45:10.94: [ 8445]: REMOTE best vres 7.7 line/mm
Mar 08 12:45:10.94: [ 8445]: REMOTE best format 2-D MR
Mar 08 12:45:10.94: [ 8445]: REMOTE best 10 ms, 5 ms/scanline
Mar 08 12:45:10.94: [ 8445]: USE 14400 bit/s
Mar 08 12:45:10.94: [ 8445]: USE 10 ms, 5 ms/scanline
Mar 08 12:45:10.94: [ 8445]: SEND file "docq/doc9.ps;31"
Mar 08 12:45:10.94: [ 8445]: USE page width 1728 pixels in 215 mm
Mar 08 12:45:10.94: [ 8445]: USE unlimited page length
Mar 08 12:45:10.94: [ 8445]: USE 7.7 line/mm
Mar 08 12:45:10.94: [ 8445]: USE 1-D MR
Mar 08 12:45:10.94: [ 8445]: <-- [23:AT+FIS=1,5,0,2,0,0,0,2\r]
Mar 08 12:45:11.18: [ 8445]: --> [2:OK]
Mar 08 12:45:11.18: [ 8445]: <-- [7:AT+FDT\r]
Mar 08 12:45:11.46: [ 8445]: --> [20:+FCS:1,5,0,2,0,0,0,2]
Mar 08 12:45:18.31: [ 8445]: --> [7:CONNECT]
Mar 08 12:45:18.31: [ 8445]: SEND begin page
Mar 08 12:45:18.31: [ 8445]: <-- data [1030]
<more data lines are cut for brevity>
Mar 08 12:45:38.31: [ 8445]: <-- data [738]
Mar 08 12:45:40.31: [ 8445]: SENT 42721 bytes of data
Mar 08 12:45:40.31: [ 8445]: SEND 1D RTC
Mar 08 12:45:40.31: [ 8445]: <-- data [9]
Mar 08 12:45:40.31: [ 8445]: SEND end page
Mar 08 12:45:40.31: [ 8445]: SEND send EOP (no more pages or documents)
Mar 08 12:45:40.31: [ 8445]: <-- data [2]
Mar 08 12:45:46.88: [ 8445]: --> [7:+FHS:00]
Mar 08 12:45:46.88: [ 8445]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Mar 08 12:45:46.88: [ 8445]: SEND recv MCF (message confirmation)
Mar 08 12:45:46.88: [ 8445]: SEND FAX (00000010): FROM
root@secure.intgrp.com TO
 2977186 (page 1 of 1 sent in 0:36)
Mar 08 12:45:46.88: [ 8445]: SEND FAX (00000010): FROM
root@secure.intgrp.com TO
 2977186 (docq/doc9.ps;31 sent in 0:36)
Mar 08 12:45:46.88: [ 8445]: <-- [5:ATH0\r]
Mar 08 12:45:47.00: [ 8445]: --> [2:OK]
Mar 08 12:45:47.00: [ 8445]: SESSION END




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null