Re: [hylafax-users] Unspecified Transmit Phase B error

[Dmitry Bely <dbely@mail.ru>]

Matthias Gelbhardt <look@commy.de> writes:

> I have a really serious problem with our hylafax-installation. The Modem
> connected to the server is an Elsa MicroLink 28.8TQV, and the following
> ist printed to the Log, when the sevrer tries to send a fax:
> 
> Sep 25 17:14:44.61: [ 9570]: SESSION BEGIN 00001595 4925121
> Sep 25 17:14:44.61: [ 9570]: SEND FAX: JOB 368 DEST 21 COMMID 00001595
> Sep 25 17:14:44.61: [ 9570]: DELAY 2600 ms
> Sep 25 17:14:47.21: [ 9570]: <-- [17:ATx3E0V1Q0S0=0H0\r]
> Sep 25 17:14:47.23: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.23: [ 9570]: <-- [21:ATS8=2S7=60&K4&D2&C1\r]
> Sep 25 17:14:47.26: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.26: [ 9570]: <-- [14:AT+FCLASS=2.0\r]
> Sep 25 17:14:47.28: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.28: [ 9570]: <-- [9:AT+FLO=1\r]
> Sep 25 17:14:47.30: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.30: [ 9570]: <-- [9:AT+FPP=0\r]
> Sep 25 17:14:47.32: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.32: [ 9570]: <-- [9:AT+FBO=0\r]
> Sep 25 17:14:47.34: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.34: [ 9570]: <-- [10:AT+FCT=30\r]
> Sep 25 17:14:47.36: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.36: [ 9570]: <-- [15:AT+FNR=1,1,1,0\r]
> Sep 25 17:14:47.38: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.38: [ 9570]: <-- [9:AT+FIE=0\r]
> Sep 25 17:14:47.40: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.40: [ 9570]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Sep 25 17:14:47.42: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.42: [ 9570]: <-- [5:ATM0\r]
> Sep 25 17:14:47.43: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.43: [ 9570]: <-- [14:AT+FCLASS=2.0\r]
> Sep 25 17:14:47.55: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.55: [ 9570]: <-- [9:AT+FLO=1\r]
> Sep 25 17:14:47.67: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.67: [ 9570]: <-- [9:AT+FPP=0\r]
> Sep 25 17:14:47.79: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.79: [ 9570]: <-- [9:AT+FBO=0\r]
> Sep 25 17:14:47.91: [ 9570]: --> [2:OK]
> Sep 25 17:14:47.91: [ 9570]: <-- [10:AT+FCT=30\r]
> Sep 25 17:14:48.03: [ 9570]: --> [2:OK]
> Sep 25 17:14:48.03: [ 9570]: <-- [15:AT+FNR=1,1,1,0\r]
> Sep 25 17:14:48.15: [ 9570]: --> [2:OK]
> Sep 25 17:14:48.15: [ 9570]: <-- [9:AT+FIE=0\r]
> Sep 25 17:14:48.27: [ 9570]: --> [2:OK]
> Sep 25 17:14:48.27: [ 9570]: <-- [23:AT+FCC=1,5,2,2,0,0,0,0\r]
> Sep 25 17:14:48.39: [ 9570]: --> [2:OK]
> Sep 25 17:14:48.39: [ 9570]: <-- [24:AT+FLI="GLOBE Mail2Fax"\r]
> Sep 25 17:14:48.52: [ 9570]: --> [2:OK]
> Sep 25 17:14:48.52: [ 9570]: DIAL 21
> Sep 25 17:14:48.52: [ 9570]: <-- [7:ATDT21\r]
> Sep 25 17:15:04.96: [ 9570]: --> [4:+FCO]
> Sep 25 17:15:07.81: [ 9570]: --> [27:+FCI:"       49 251 520521"]
> Sep 25 17:15:07.81: [ 9570]: REMOTE CSI "49 251 520521"
> Sep 25 17:15:07.81: [ 9570]: --> [20:+FIS:1,5,0,2,1,1,0,3]
> Sep 25 17:15:07.81: [ 9570]: --> [2:OK]
> Sep 25 17:15:07.81: [ 9570]: REMOTE best rate 14400 bit/s
> Sep 25 17:15:07.81: [ 9570]: REMOTE max page width 1728 pixels in 215 mm
> Sep 25 17:15:07.81: [ 9570]: REMOTE max unlimited page length 
> Sep 25 17:15:07.81: [ 9570]: REMOTE best vres 7.7 line/mm
> Sep 25 17:15:07.81: [ 9570]: REMOTE best format 2-D MR
> Sep 25 17:15:07.81: [ 9570]: REMOTE supports T.30 Annex A, ECM
> Sep 25 17:15:07.81: [ 9570]: REMOTE best 10 ms/scanline
> Sep 25 17:15:07.81: [ 9570]: USE 14400 bit/s
> Sep 25 17:15:07.81: [ 9570]: USE 10 ms/scanline
> Sep 25 17:15:07.81: [ 9570]: <-- [5:ATH0\r]

That's known Hylafax bug. Usually it behaves so when Ghostcript (or Hylafax
itself -- I am too lazy to find it out for sure :-)) does not recognize the 
submitted data as Postscript (due to PJL commands inside etc.) and marks it
as "data" instead "postscript" in job's qfile. Then Hylafax fails to
convert them to TIFF and hangs up immediately after "CONNECT" with that
stupid diagnostics (it understands too late that the job has no data to
send). If you are trying to fax from Windows client, replace the printer
driver with "Apple Laser Writer 16/600" (for WinNT -- Win 9x has the
similar one), any all chances that the problem will be solved.

> Sep 25 17:15:09.43: [ 9570]: --> [7:+FHS:20]
> Sep 25 17:15:09.43: [ 9570]: REMOTE HANGUP: Unspecified Transmit Phase B
> error (code 20)
> Sep 25 17:15:10.32: [ 9570]: --> [2:OK]
> Sep 25 17:15:10.32: [ 9570]: SESSION END
> 
> I have tried four fax-clients (two here in our company, two mailboxes).
> 
> I hope someone can help me

Hope to hear from you soon,
Dmitry

To -devel people: is there a person, who is familiar with Hylafax
queuer/Postscript stuff and is able to fix this?




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null