[hylafax-users] problems setting up a send-only HylaFAX

To: hylafax-users@hylafax.org
Subject: [hylafax-users] problems setting up a send-only HylaFAX
From: Marko Asplund <aspa@kronodoc.fi>
Date: Mon, 25 Sep 2000 08:40:34 +0300 (EEST)


i'm trying to setup a send-only HylaFAX v4.1beta2 system from a RPM
package (hylafax-4.1beta2-7rh6) on a RedHat v6.2 linux system. libtiff is
version 3.5.5 and i use a Rockwell AC/K56 based modem. modem configuration
is based on the rockwell-k56 config file with the following line added for
dialing out: 'ModemDialCmd: ATDT0,%s'.

when starting HylaFAX (faxq, hfaxd) the system goes into 'Waiting for
modem to come ready' as reported by 'faxstat -i'. nothing seems to happen
even if i spool a fax job with sendfax. only after using faxstate for
setting HylaFAX to a ready state the system will proceed with fax
transmission.

the fax transmission fails, however. the first attempt with the
error messages:
	...
	Document was encoded with 2DMR, but modem does not support this
	data format
	<-- [5:ATH0\r]
	--> [9:+FHNG: 20]
	REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
	--> [2:OK]
	SESSION END

and the second attempt:
	...
	DIAL 25173053
	<-- [15:ATDT0,25173053\r]
	--> [8:+FHNG: 1]
	REMOTE HANGUP: Ring detect without successful handshake (code 1)
	SEND FAILED: Ring detect without successful handshake
	<-- [5:ATH0\r]
	--> [2:OK]
	SESSION END

consecutive attempts fail with error messages similar to the above until
the job is rejected because of too many errors (log files attached). i've
migrated from mgetty+sendfax to HylaFAX and i've been able to successfully
talk to the fax machine in question with mgetty+sendfax. does someone have
any ideas on what's going on here?

thanks,

regards,
-- 
	aspa

Sep 25 07:49:55.52: [15424]: SESSION BEGIN 00000010 358925173053
Sep 25 07:49:55.52: [15424]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000010
Sep 25 07:49:55.52: [15424]: DELAY 2600 ms
Sep 25 07:49:58.12: [15424]: <-- [4:ATZ\r]
Sep 25 07:49:58.24: [15424]: --> [2:OK]
Sep 25 07:49:58.24: [15424]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 07:49:58.25: [15424]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 07:49:58.25: [15424]: --> [2:OK]
Sep 25 07:49:58.25: [15424]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 07:49:58.27: [15424]: --> [2:OK]
Sep 25 07:49:58.27: [15424]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:49:58.28: [15424]: --> [2:OK]
Sep 25 07:49:58.28: [15424]: <-- [10:AT+FTBC=0\r]
Sep 25 07:49:58.29: [15424]: --> [2:OK]
Sep 25 07:49:58.29: [15424]: <-- [10:AT+FBOR=0\r]
Sep 25 07:49:58.30: [15424]: --> [2:OK]
Sep 25 07:49:58.30: [15424]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:49:58.31: [15424]: --> [2:OK]
Sep 25 07:49:58.31: [15424]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:49:58.32: [15424]: --> [2:OK]
Sep 25 07:49:58.32: [15424]: <-- [5:ATM0\r]
Sep 25 07:49:58.33: [15424]: --> [2:OK]
Sep 25 07:49:58.33: [15424]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:49:58.44: [15424]: --> [2:OK]
Sep 25 07:49:58.44: [15424]: <-- [10:AT+FTBC=0\r]
Sep 25 07:49:58.55: [15424]: --> [2:OK]
Sep 25 07:49:58.55: [15424]: <-- [10:AT+FBOR=0\r]
Sep 25 07:49:58.66: [15424]: --> [2:OK]
Sep 25 07:49:58.66: [15424]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:49:58.77: [15424]: --> [2:OK]
Sep 25 07:49:58.77: [15424]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:49:58.88: [15424]: --> [2:OK]
Sep 25 07:49:58.88: [15424]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 07:49:58.99: [15424]: --> [2:OK]
Sep 25 07:49:59.01: [15424]: DIAL 25173053
Sep 25 07:49:59.01: [15424]: <-- [15:ATDT0,25173053\r]
Sep 25 07:50:22.29: [15424]: --> [5:+FCON]
Sep 25 07:50:25.04: [15424]: --> [29:+FCSI: "      358 9 43543053"]
Sep 25 07:50:25.04: [15424]: REMOTE CSI "358 9 43543053"
Sep 25 07:50:25.30: [15424]: --> [22:+FDIS: 1,5,0,2,1,0,0,3]
Sep 25 07:50:25.41: [15424]: --> [2:OK]
Sep 25 07:50:25.41: [15424]: REMOTE best rate 14400 bit/s
Sep 25 07:50:25.41: [15424]: REMOTE max page width 1728 pixels in 215 mm
Sep 25 07:50:25.41: [15424]: REMOTE max unlimited page length 
Sep 25 07:50:25.41: [15424]: REMOTE best vres 7.7 line/mm
Sep 25 07:50:25.41: [15424]: REMOTE best format 2-D MR
Sep 25 07:50:25.41: [15424]: REMOTE best 10 ms/scanline
Sep 25 07:50:25.41: [15424]: USE 14400 bit/s
Sep 25 07:50:25.41: [15424]: USE 10 ms/scanline
Sep 25 07:50:25.41: [15424]: SEND file "docq/doc4.cover;71"
Sep 25 07:50:25.41: [15424]: Document was encoded with 2DMR, but modem does not support this data format
Sep 25 07:50:25.41: [15424]: <-- [5:ATH0\r]
Sep 25 07:50:25.67: [15424]: --> [9:+FHNG: 20]
Sep 25 07:50:25.67: [15424]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Sep 25 07:50:27.48: [15424]: --> [2:OK]
Sep 25 07:50:27.48: [15424]: SESSION END

Sep 25 07:50:32.99: [15446]: SESSION BEGIN 00000011 358925173053
Sep 25 07:50:32.99: [15446]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000011
Sep 25 07:50:32.99: [15446]: DELAY 2600 ms
Sep 25 07:50:35.59: [15446]: <-- [4:ATZ\r]
Sep 25 07:50:35.71: [15446]: --> [2:OK]
Sep 25 07:50:35.71: [15446]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 07:50:35.72: [15446]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 07:50:35.72: [15446]: --> [2:OK]
Sep 25 07:50:35.72: [15446]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 07:50:35.74: [15446]: --> [2:OK]
Sep 25 07:50:35.74: [15446]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:50:35.75: [15446]: --> [2:OK]
Sep 25 07:50:35.75: [15446]: <-- [10:AT+FTBC=0\r]
Sep 25 07:50:35.76: [15446]: --> [2:OK]
Sep 25 07:50:35.76: [15446]: <-- [10:AT+FBOR=0\r]
Sep 25 07:50:35.77: [15446]: --> [2:OK]
Sep 25 07:50:35.77: [15446]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:50:35.78: [15446]: --> [2:OK]
Sep 25 07:50:35.78: [15446]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:50:35.79: [15446]: --> [2:OK]
Sep 25 07:50:35.79: [15446]: <-- [5:ATM0\r]
Sep 25 07:50:35.80: [15446]: --> [2:OK]
Sep 25 07:50:35.80: [15446]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:50:35.91: [15446]: --> [2:OK]
Sep 25 07:50:35.91: [15446]: <-- [10:AT+FTBC=0\r]
Sep 25 07:50:36.02: [15446]: --> [2:OK]
Sep 25 07:50:36.02: [15446]: <-- [10:AT+FBOR=0\r]
Sep 25 07:50:36.13: [15446]: --> [2:OK]
Sep 25 07:50:36.13: [15446]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:50:36.24: [15446]: --> [2:OK]
Sep 25 07:50:36.24: [15446]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:50:36.35: [15446]: --> [2:OK]
Sep 25 07:50:36.35: [15446]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 07:50:36.46: [15446]: --> [2:OK]
Sep 25 07:50:36.46: [15446]: DIAL 25173053
Sep 25 07:50:36.46: [15446]: <-- [15:ATDT0,25173053\r]
Sep 25 07:51:48.21: [15446]: --> [8:+FHNG: 1]
Sep 25 07:51:48.21: [15446]: REMOTE HANGUP: Ring detect without successful handshake (code 1)
Sep 25 07:51:48.21: [15446]: SEND FAILED: Ring detect without successful handshake
Sep 25 07:51:48.21: [15446]: <-- [5:ATH0\r]
Sep 25 07:51:50.03: [15446]: --> [2:OK]
Sep 25 07:51:50.03: [15446]: SESSION END

Sep 25 07:59:07.83: [15532]: SESSION BEGIN 00000012 358925173053
Sep 25 07:59:07.83: [15532]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000012
Sep 25 07:59:07.83: [15532]: DELAY 2600 ms
Sep 25 07:59:10.43: [15532]: <-- [4:ATZ\r]
Sep 25 07:59:10.55: [15532]: --> [2:OK]
Sep 25 07:59:10.55: [15532]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 07:59:10.56: [15532]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 07:59:10.56: [15532]: --> [2:OK]
Sep 25 07:59:10.56: [15532]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 07:59:10.58: [15532]: --> [2:OK]
Sep 25 07:59:10.58: [15532]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:59:10.59: [15532]: --> [2:OK]
Sep 25 07:59:10.59: [15532]: <-- [10:AT+FTBC=0\r]
Sep 25 07:59:10.60: [15532]: --> [2:OK]
Sep 25 07:59:10.60: [15532]: <-- [10:AT+FBOR=0\r]
Sep 25 07:59:10.61: [15532]: --> [2:OK]
Sep 25 07:59:10.61: [15532]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:59:10.62: [15532]: --> [2:OK]
Sep 25 07:59:10.62: [15532]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:59:10.63: [15532]: --> [2:OK]
Sep 25 07:59:10.63: [15532]: <-- [5:ATM0\r]
Sep 25 07:59:10.64: [15532]: --> [2:OK]
Sep 25 07:59:10.64: [15532]: <-- [12:AT+FCLASS=2\r]
Sep 25 07:59:10.75: [15532]: --> [2:OK]
Sep 25 07:59:10.75: [15532]: <-- [10:AT+FTBC=0\r]
Sep 25 07:59:10.86: [15532]: --> [2:OK]
Sep 25 07:59:10.86: [15532]: <-- [10:AT+FBOR=0\r]
Sep 25 07:59:10.97: [15532]: --> [2:OK]
Sep 25 07:59:10.97: [15532]: <-- [13:AT+FPHCTO=30\r]
Sep 25 07:59:11.08: [15532]: --> [2:OK]
Sep 25 07:59:11.08: [15532]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 07:59:11.19: [15532]: --> [2:OK]
Sep 25 07:59:11.19: [15532]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 07:59:11.30: [15532]: --> [2:OK]
Sep 25 07:59:11.30: [15532]: DIAL 25173053
Sep 25 07:59:11.30: [15532]: <-- [15:ATDT0,25173053\r]
Sep 25 08:00:22.25: [15532]: --> [8:+FHNG: 1]
Sep 25 08:00:22.25: [15532]: REMOTE HANGUP: Ring detect without successful handshake (code 1)
Sep 25 08:00:22.25: [15532]: SEND FAILED: Ring detect without successful handshake
Sep 25 08:00:22.25: [15532]: <-- [5:ATH0\r]
Sep 25 08:00:24.07: [15532]: --> [2:OK]
Sep 25 08:00:24.07: [15532]: SESSION END

Sep 25 08:07:44.87: [15568]: SESSION BEGIN 00000013 358925173053
Sep 25 08:07:44.87: [15568]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000013
Sep 25 08:07:44.87: [15568]: DELAY 2600 ms
Sep 25 08:07:47.47: [15568]: <-- [4:ATZ\r]
Sep 25 08:07:47.59: [15568]: --> [2:OK]
Sep 25 08:07:47.59: [15568]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 08:07:47.60: [15568]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 08:07:47.60: [15568]: --> [2:OK]
Sep 25 08:07:47.60: [15568]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 08:07:47.62: [15568]: --> [2:OK]
Sep 25 08:07:47.62: [15568]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:07:47.63: [15568]: --> [2:OK]
Sep 25 08:07:47.63: [15568]: <-- [10:AT+FTBC=0\r]
Sep 25 08:07:47.64: [15568]: --> [2:OK]
Sep 25 08:07:47.64: [15568]: <-- [10:AT+FBOR=0\r]
Sep 25 08:07:47.65: [15568]: --> [2:OK]
Sep 25 08:07:47.65: [15568]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:07:47.66: [15568]: --> [2:OK]
Sep 25 08:07:47.66: [15568]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:07:47.67: [15568]: --> [2:OK]
Sep 25 08:07:47.67: [15568]: <-- [5:ATM0\r]
Sep 25 08:07:47.68: [15568]: --> [2:OK]
Sep 25 08:07:47.68: [15568]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:07:47.79: [15568]: --> [2:OK]
Sep 25 08:07:47.79: [15568]: <-- [10:AT+FTBC=0\r]
Sep 25 08:07:47.90: [15568]: --> [2:OK]
Sep 25 08:07:47.90: [15568]: <-- [10:AT+FBOR=0\r]
Sep 25 08:07:48.01: [15568]: --> [2:OK]
Sep 25 08:07:48.01: [15568]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:07:48.12: [15568]: --> [2:OK]
Sep 25 08:07:48.12: [15568]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:07:48.23: [15568]: --> [2:OK]
Sep 25 08:07:48.23: [15568]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 08:07:48.34: [15568]: --> [2:OK]
Sep 25 08:07:48.34: [15568]: DIAL 25173053
Sep 25 08:07:48.34: [15568]: <-- [15:ATDT0,25173053\r]
Sep 25 08:08:11.75: [15568]: --> [5:+FCON]
Sep 25 08:08:14.46: [15568]: --> [29:+FCSI: "      358 9 43543053"]
Sep 25 08:08:14.46: [15568]: REMOTE CSI "358 9 43543053"
Sep 25 08:08:14.83: [15568]: --> [22:+FDIS: 1,5,0,2,1,0,0,3]
Sep 25 08:08:14.83: [15568]: --> [2:OK]
Sep 25 08:08:14.83: [15568]: REMOTE best rate 14400 bit/s
Sep 25 08:08:14.83: [15568]: REMOTE max page width 1728 pixels in 215 mm
Sep 25 08:08:14.83: [15568]: REMOTE max unlimited page length 
Sep 25 08:08:14.83: [15568]: REMOTE best vres 7.7 line/mm
Sep 25 08:08:14.83: [15568]: REMOTE best format 2-D MR
Sep 25 08:08:14.83: [15568]: REMOTE best 10 ms/scanline
Sep 25 08:08:14.83: [15568]: USE 14400 bit/s
Sep 25 08:08:14.83: [15568]: USE 10 ms/scanline
Sep 25 08:08:14.83: [15568]: SEND file "docq/doc4.cover;71"
Sep 25 08:08:14.83: [15568]: Document was encoded with 2DMR, but modem does not support this data format
Sep 25 08:08:14.83: [15568]: <-- [5:ATH0\r]
Sep 25 08:08:15.09: [15568]: --> [9:+FHNG: 20]
Sep 25 08:08:15.09: [15568]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Sep 25 08:08:16.90: [15568]: --> [2:OK]
Sep 25 08:08:16.90: [15568]: SESSION END

Sep 25 08:08:22.40: [15596]: SESSION BEGIN 00000014 358925173053
Sep 25 08:08:22.40: [15596]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000014
Sep 25 08:08:22.40: [15596]: DELAY 2600 ms
Sep 25 08:08:25.00: [15596]: <-- [4:ATZ\r]
Sep 25 08:08:25.12: [15596]: --> [2:OK]
Sep 25 08:08:25.12: [15596]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 08:08:25.13: [15596]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 08:08:25.13: [15596]: --> [2:OK]
Sep 25 08:08:25.13: [15596]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 08:08:25.15: [15596]: --> [2:OK]
Sep 25 08:08:25.15: [15596]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:08:25.16: [15596]: --> [2:OK]
Sep 25 08:08:25.16: [15596]: <-- [10:AT+FTBC=0\r]
Sep 25 08:08:25.17: [15596]: --> [2:OK]
Sep 25 08:08:25.17: [15596]: <-- [10:AT+FBOR=0\r]
Sep 25 08:08:25.18: [15596]: --> [2:OK]
Sep 25 08:08:25.18: [15596]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:08:25.19: [15596]: --> [2:OK]
Sep 25 08:08:25.19: [15596]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:08:25.20: [15596]: --> [2:OK]
Sep 25 08:08:25.20: [15596]: <-- [5:ATM0\r]
Sep 25 08:08:25.21: [15596]: --> [2:OK]
Sep 25 08:08:25.21: [15596]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:08:25.32: [15596]: --> [2:OK]
Sep 25 08:08:25.32: [15596]: <-- [10:AT+FTBC=0\r]
Sep 25 08:08:25.43: [15596]: --> [2:OK]
Sep 25 08:08:25.43: [15596]: <-- [10:AT+FBOR=0\r]
Sep 25 08:08:25.54: [15596]: --> [2:OK]
Sep 25 08:08:25.54: [15596]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:08:25.65: [15596]: --> [2:OK]
Sep 25 08:08:25.65: [15596]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:08:25.76: [15596]: --> [2:OK]
Sep 25 08:08:25.76: [15596]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 08:08:25.87: [15596]: --> [2:OK]
Sep 25 08:08:25.87: [15596]: DIAL 25173053
Sep 25 08:08:25.87: [15596]: <-- [15:ATDT0,25173053\r]
Sep 25 08:09:37.31: [15596]: --> [8:+FHNG: 1]
Sep 25 08:09:37.31: [15596]: REMOTE HANGUP: Ring detect without successful handshake (code 1)
Sep 25 08:09:37.31: [15596]: SEND FAILED: Ring detect without successful handshake
Sep 25 08:09:37.31: [15596]: <-- [5:ATH0\r]
Sep 25 08:09:39.13: [15596]: --> [2:OK]
Sep 25 08:09:39.13: [15596]: SESSION END

Sep 25 08:15:10.93: [15615]: SESSION BEGIN 00000015 358925173053
Sep 25 08:15:10.93: [15615]: SEND FAX: JOB 4 DEST 25173053 COMMID 00000015
Sep 25 08:15:10.93: [15615]: DELAY 2600 ms
Sep 25 08:15:13.53: [15615]: <-- [4:ATZ\r]
Sep 25 08:15:13.65: [15615]: --> [2:OK]
Sep 25 08:15:13.65: [15615]: <-- [15:ATE0V1Q0S0=0H0\r]
Sep 25 08:15:13.66: [15615]: --> [14:ATE0V1Q0S0=0H0]
Sep 25 08:15:13.66: [15615]: --> [2:OK]
Sep 25 08:15:13.66: [15615]: <-- [21:ATS8=2S7=60&K4&D3&C1\r]
Sep 25 08:15:13.68: [15615]: --> [2:OK]
Sep 25 08:15:13.68: [15615]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:15:13.69: [15615]: --> [2:OK]
Sep 25 08:15:13.69: [15615]: <-- [10:AT+FTBC=0\r]
Sep 25 08:15:13.70: [15615]: --> [2:OK]
Sep 25 08:15:13.70: [15615]: <-- [10:AT+FBOR=0\r]
Sep 25 08:15:13.71: [15615]: --> [2:OK]
Sep 25 08:15:13.71: [15615]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:15:13.72: [15615]: --> [2:OK]
Sep 25 08:15:13.72: [15615]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:15:13.73: [15615]: --> [2:OK]
Sep 25 08:15:13.73: [15615]: <-- [5:ATM0\r]
Sep 25 08:15:13.74: [15615]: --> [2:OK]
Sep 25 08:15:13.74: [15615]: <-- [12:AT+FCLASS=2\r]
Sep 25 08:15:13.85: [15615]: --> [2:OK]
Sep 25 08:15:13.85: [15615]: <-- [10:AT+FTBC=0\r]
Sep 25 08:15:13.96: [15615]: --> [2:OK]
Sep 25 08:15:13.96: [15615]: <-- [10:AT+FBOR=0\r]
Sep 25 08:15:14.07: [15615]: --> [2:OK]
Sep 25 08:15:14.07: [15615]: <-- [13:AT+FPHCTO=30\r]
Sep 25 08:15:14.18: [15615]: --> [2:OK]
Sep 25 08:15:14.18: [15615]: <-- [24:AT+FDCC=1,5,2,2,0,0,0,0\r]
Sep 25 08:15:14.29: [15615]: --> [2:OK]
Sep 25 08:15:14.29: [15615]: <-- [23:AT+FLID="NothingSetup"\r]
Sep 25 08:15:14.40: [15615]: --> [2:OK]
Sep 25 08:15:14.42: [15615]: DIAL 25173053
Sep 25 08:15:14.42: [15615]: <-- [15:ATDT0,25173053\r]
Sep 25 08:15:37.65: [15615]: --> [5:+FCON]
Sep 25 08:15:40.36: [15615]: --> [29:+FCSI: "      358 9 43543053"]
Sep 25 08:15:40.36: [15615]: REMOTE CSI "358 9 43543053"
Sep 25 08:15:40.62: [15615]: --> [22:+FDIS: 1,5,0,2,1,0,0,3]
Sep 25 08:15:40.73: [15615]: --> [2:OK]
Sep 25 08:15:40.73: [15615]: REMOTE best rate 14400 bit/s
Sep 25 08:15:40.73: [15615]: REMOTE max page width 1728 pixels in 215 mm
Sep 25 08:15:40.73: [15615]: REMOTE max unlimited page length 
Sep 25 08:15:40.73: [15615]: REMOTE best vres 7.7 line/mm
Sep 25 08:15:40.73: [15615]: REMOTE best format 2-D MR
Sep 25 08:15:40.73: [15615]: REMOTE best 10 ms/scanline
Sep 25 08:15:40.73: [15615]: USE 14400 bit/s
Sep 25 08:15:40.73: [15615]: USE 10 ms/scanline
Sep 25 08:15:40.73: [15615]: SEND file "docq/doc4.cover;71"
Sep 25 08:15:40.73: [15615]: Document was encoded with 2DMR, but modem does not support this data format
Sep 25 08:15:40.73: [15615]: <-- [5:ATH0\r]
Sep 25 08:15:40.98: [15615]: --> [9:+FHNG: 20]
Sep 25 08:15:40.98: [15615]: REMOTE HANGUP: Unspecified Transmit Phase B error (code 20)
Sep 25 08:15:42.79: [15615]: --> [2:OK]
Sep 25 08:15:42.79: [15615]: SESSION END

Follow-Ups:
- Re: [hylafax-users] problems setting up a send-only HylaFAX
  - From: Lee Howard <faxguy@deanox.com>

Prev by Date: Re: [hylafax-users] help to initialize multitech 56k modem
Next by Date: Re: [hylafax-users] help to initialize multitech 56k modem
Prev by thread: Re: [hylafax-users] Windows Client
Next by thread: Re: [hylafax-users] problems setting up a send-only HylaFAX
Index(es):
- Main
- Thread

Project hosted by iFAX Solutions