Re: [hylafax-users] Unspecified Transmit Phase B error (code 20)

[Dmitry Bely <dbely@mail.ru>]

Ricardo Pastor <rpastor@tsc.es> writes:

> I apologize Dmitry, my english in not very great.

Me too :-)
 
> HylaFAX can't connect properly with fax on the +49 8331 8558 11 but
> others faxmachines sending fax with no problems.
> 
> HylaFAX Version 4.0pl2 under Linux RedHat 6.1 Kernel 2.2.12-20
  ^^^^^^^^^^^^^^^^^^^^^^
Doubt that it works at all :-) Go to ftp://ftp.hylafax.org and grab the
most recent 4.1 beta RPM.

> modem Multitech MT932BA
> 
> I've been trying to modify the file /var/spool/fax/etc/config.ttyS1
>         a) Use2D: no
>         b) Class2DDISCmd:      AT+FDIS
>         c) ModemRate:          9600
             ^^^^^^^^^^^^^^^^^^^^^^^^
Unacceptable! At least 19200 is required (for many modems 19200 is the only 
possible speed for fax operation).

>         d) initialization for the modem out of the box: AT&F, ATS38=35,
> AT&F9,
> AT&W0

Use also ModemResetCmds: ATZ to reset the modem in the beginning of each
session (not necessary for the latest version -- it do ATZ itself).

> but each sendig hangs with Unspecified Transmit Phase B error (code 20)
> 
> The log show:
> -------------
> Sep 15 01:09:29.78: [ 1660]: <-- [19:ATDT00498331855811\r]
> Sep 15 01:09:50.74: [ 1660]: --> [5:+FCON]
> Sep 15 01:09:53.96: [ 1660]: --> [78:+FNSF:00 00 25 01 4E 45 47 4E 49 4D
> 4D 45 4D 20 48 42 4D 47 20 41 43 45 54 53 ]
> Sep 15 01:09:53.96: [ 1660]: REMOTE NSF "00 00 25 01 4E 45 47 4E 49 4D
> 4D 45 4D 20 48 42 4D 47 20 41 43 45 54 53"
> Sep 15 01:09:53.96: [ 1660]: --> [28:+FCSI:"     +49 8331 855811"]
> Sep 15 01:09:53.96: [ 1660]: REMOTE CSI "+49 8331 855811"
> Sep 15 01:09:53.96: [ 1660]: --> [6:+FDIS:]

Your modem was unable to identify the remote fax machine capabilities. Maybe 
ATZ as the init command would help (I again recommend you to use more recent
Hylafax!), but many chances that this is the firmware bug and so cannot be
fixed at the software level. Try another modem ...

I've just tried this destination with my Zyxel 1496 in Class1 mode (have
they changed their fax machine? NSF is different):

Sep 20 00:28:22.06: [17562]: SESSION BEGIN 00008823 710498331855811
Sep 20 00:28:22.06: [17562]: SEND FAX: JOB 2167 DEST 810498331855811 COMMID 00008823
Sep 20 00:28:22.06: [17562]: MODEM set DTR OFF
Sep 20 00:28:22.06: [17562]: DELAY 2600 ms
Sep 20 00:28:24.66: [17562]: MODEM set DTR ON
Sep 20 00:28:24.66: [17562]: MODEM set baud rate: 19200 baud, input flow XON/XOFF, output flow XON/XOFF
Sep 20 00:28:24.67: [17562]: MODEM flush i/o
Sep 20 00:28:24.67: [17562]: <-- [4:ATZ\r]
Sep 20 00:28:24.82: [17562]: --> [2:OK]
Sep 20 00:28:24.82: [17562]: <-- [25:AT*P7S38.3=1E0V1Q0S0=0H0\r]
Sep 20 00:28:24.99: [17562]: --> [24:AT*P7S38.3=1E0V1Q0S0=0H0]
Sep 20 00:28:24.99: [17562]: --> [2:OK]
Sep 20 00:28:24.99: [17562]: <-- [21:ATS8=2S7=60&H4&D2&C1\r]
Sep 20 00:28:25.02: [17562]: --> [2:OK]
Sep 20 00:28:25.02: [17562]: <-- [12:AT+FCLASS=1\r]
Sep 20 00:28:25.12: [17562]: --> [2:OK]
Sep 20 00:28:25.12: [17562]: <-- [7:ATM1L5\r]
Sep 20 00:28:25.14: [17562]: --> [2:OK]
Sep 20 00:28:25.14: [17562]: STATE CHANGE: RUNNING -> SENDING
Sep 20 00:28:25.14: [17562]: MODEM input buffering enabled
Sep 20 00:28:25.15: [17562]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled
Sep 20 00:28:25.15: [17562]: DIAL S7=60S8=15DT804w61498331855811,
Sep 20 00:28:25.15: [17562]: <-- [34:ATS7=60S8=15DT804w61498331855811,\r]
Sep 20 00:28:50.92: [17562]: --> [7:CONNECT]
Sep 20 00:28:50.92: [17562]: MODEM input buffering disabled
Sep 20 00:28:52.22: [17562]: --> NSF signal: HDLC<22:FF C0 04 B5 00 22 00 00 00 48 08 B6 40 00 0A 00 14 1D 05 01 01 88>
Sep 20 00:28:52.22: [17562]: --> [2:OK]
Sep 20 00:28:52.22: [17562]: REMOTE NSF "AD 00 44 00 00 00 12 10 6D 02 00 50 00 28 B8 A0 80 80"
Sep 20 00:28:52.22: [17562]: NSF remote fax equipment: unknown 
Sep 20 00:28:52.22: [17562]: <-- [9:AT+FRH=3\r]
Sep 20 00:28:52.25: [17562]: --> [7:CONNECT]
Sep 20 00:28:53.05: [17562]: --> NSF signal: HDLC<27:FF C0 04 B5 00 22 80 72 A2 E2 72 92 B2 B2 A2 B2 04 12 42 B2 E2 04 82 C2 A2 2A CA>
Sep 20 00:28:53.06: [17562]: --> [2:OK]
Sep 20 00:28:53.06: [17562]: REMOTE NSF "AD 00 44 01 4E 45 47 4E 49 4D 4D 45 4D 20 48 42 4D 47 20 41 43 45 54"
Sep 20 00:28:53.06: [17562]: NSF remote fax equipment: unknown 
Sep 20 00:28:53.06: [17562]: NSF remote station ID: "TECA GMBH MEMMINGEN"
Sep 20 00:28:53.06: [17562]: <-- [9:AT+FRH=3\r]
Sep 20 00:28:53.09: [17562]: --> [7:CONNECT]
Sep 20 00:28:53.79: [17562]: --> CSI signal: HDLC<23:FF C0 02 8C 8C 1C AC AC 1C 04 8C CC CC 1C 04 9C 2C D4 04 04 04 04 04>
Sep 20 00:28:53.79: [17562]: --> [2:OK]
Sep 20 00:28:53.79: [17562]: REMOTE CSI "+49 8331 855811"
Sep 20 00:28:53.79: [17562]: <-- [9:AT+FRH=3\r]
Sep 20 00:28:53.81: [17562]: --> [7:CONNECT]
Sep 20 00:28:54.15: [17562]: --> DIS signal: HDLC<10:FF C8 01 00 73 15 23 01 09 80>
Sep 20 00:28:54.16: [17562]: --> [2:OK]
Sep 20 00:28:54.16: [17562]: REMOTE best rate 9600 bit/s
Sep 20 00:28:54.16: [17562]: REMOTE max page width 1728 pixels in 215 mm
Sep 20 00:28:54.16: [17562]: REMOTE max unlimited page length 
Sep 20 00:28:54.16: [17562]: REMOTE best vres 7.7 line/mm
Sep 20 00:28:54.16: [17562]: REMOTE best format 2-D MMR
Sep 20 00:28:54.16: [17562]: REMOTE supports T.30 Annex A, ECM
Sep 20 00:28:54.16: [17562]: REMOTE best 10 ms/scanline
Sep 20 00:28:54.16: [17562]: USE 9600 bit/s
Sep 20 00:28:54.16: [17562]: USE 10 ms/scanline
Sep 20 00:28:54.16: [17562]: SEND file "docq/doc1743.ps;70"
Sep 20 00:28:54.16: [17562]: USE page width 1728 pixels in 215 mm
Sep 20 00:28:54.16: [17562]: USE unlimited page length 
Sep 20 00:28:54.17: [17562]: USE 3.85 line/mm
Sep 20 00:28:54.17: [17562]: USE 2-D MR
Sep 20 00:28:54.17: [17562]: SEND training at v.29 9600 bit/s
Sep 20 00:28:54.17: [17562]: <-- [9:AT+FTH=3\r]
Sep 20 00:28:54.19: [17562]: --> [7:CONNECT]
Sep 20 00:28:54.19: [17562]: <-- TSI signal: HDLC<23:FF C0 C2 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04>
Sep 20 00:28:54.19: [17562]: <-- data [23]
Sep 20 00:28:54.19: [17562]: <-- data [2]
Sep 20 00:28:55.91: [17562]: --> [7:CONNECT]
Sep 20 00:28:55.91: [17562]: <-- DCS signal: HDLC<6:FF C8 C1 00 61 14>
Sep 20 00:28:55.91: [17562]: <-- data [6]
Sep 20 00:28:55.91: [17562]: <-- data [2]
Sep 20 00:28:56.23: [17562]: --> [2:OK]
Sep 20 00:28:56.23: [17562]: DELAY 75 ms
Sep 20 00:28:56.32: [17562]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Sep 20 00:28:56.32: [17562]: <-- [10:AT+FTM=96\r]
Sep 20 00:28:56.35: [17562]: --> [7:CONNECT]
Sep 20 00:28:56.35: [17562]: <-- data [1024]
Sep 20 00:28:56.35: [17562]: <-- data [776]
Sep 20 00:28:56.35: [17562]: <-- data [2]
Sep 20 00:28:58.37: [17562]: --> [2:OK]
Sep 20 00:28:58.37: [17562]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Sep 20 00:28:58.37: [17562]: <-- [9:AT+FRH=3\r]
Sep 20 00:28:59.77: [17562]: --> [7:CONNECT]
Sep 20 00:29:00.95: [17562]: --> CFR signal: HDLC<3:FF C8 21>
Sep 20 00:29:00.96: [17562]: --> [2:OK]
Sep 20 00:29:00.96: [17562]: TRAINING succeeded
Sep 20 00:29:00.96: [17562]: <-- [10:AT+FTM=96\r]
Sep 20 00:29:00.99: [17562]: --> [7:CONNECT]
Sep 20 00:29:00.99: [17562]: SEND begin page
Sep 20 00:29:00.99: [17562]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Sep 20 00:29:00.99: [17562]: <-- data [1024]
Sep 20 00:29:00.99: [17562]: <-- data [166]
Sep 20 00:29:00.99: [17562]: SENT 1190 bytes of data
Sep 20 00:29:00.99: [17562]: SEND 2D RTC
Sep 20 00:29:00.99: [17562]: <-- data [30]
Sep 20 00:29:00.99: [17562]: <-- data [2]
Sep 20 00:29:00.99: [17562]: SEND end page
Sep 20 00:29:02.53: [17562]: --> [2:OK]
Sep 20 00:29:02.53: [17562]: MODEM set XON/XOFF/DRAIN: input ignored, output disabled
Sep 20 00:29:02.53: [17562]: DELAY 95 ms
Sep 20 00:29:02.64: [17562]: SEND send EOP (no more pages or documents)
Sep 20 00:29:02.64: [17562]: <-- [9:AT+FTH=3\r]
Sep 20 00:29:02.67: [17562]: --> [7:CONNECT]
Sep 20 00:29:02.67: [17562]: <-- EOP signal: HDLC<3:FF C8 F4>
Sep 20 00:29:02.67: [17562]: <-- data [3]
Sep 20 00:29:02.67: [17562]: <-- data [2]
Sep 20 00:29:03.90: [17562]: --> [2:OK]
Sep 20 00:29:03.90: [17562]: <-- [9:AT+FRH=3\r]
Sep 20 00:29:05.07: [17562]: --> [7:CONNECT]
Sep 20 00:29:06.30: [17562]: --> MCF signal: HDLC<3:FF C8 31>
Sep 20 00:29:06.31: [17562]: --> [2:OK]
Sep 20 00:29:06.31: [17562]: SEND recv MCF (message confirmation)
Sep 20 00:29:06.31: [17562]: SEND FAX (00008823): FROM bely@stormoff TO 810498331855811 (page 1 of 1 sent in 0:12)
Sep 20 00:29:06.31: [17562]: SEND FAX (00008823): FROM bely@stormoff TO 810498331855811 (docq/doc1743.ps;70 sent in 0:12)
Sep 20 00:29:06.32: [17562]: <-- [9:AT+FTH=3\r]
Sep 20 00:29:06.35: [17562]: --> [7:CONNECT]
Sep 20 00:29:06.35: [17562]: <-- DCN signal: HDLC<3:FF C8 DF>
Sep 20 00:29:06.35: [17562]: <-- data [3]
Sep 20 00:29:06.35: [17562]: <-- data [2]
Sep 20 00:29:07.58: [17562]: --> [2:OK]
Sep 20 00:29:07.58: [17562]: MODEM input buffering enabled
Sep 20 00:29:07.58: [17562]: <-- [5:ATH0\r]
Sep 20 00:29:08.04: [17562]: --> [2:OK]
Sep 20 00:29:08.04: [17562]: MODEM set DTR OFF
Sep 20 00:29:08.04: [17562]: STATE CHANGE: SENDING -> MODEMWAIT (timeout 5)
Sep 20 00:29:08.04: [17562]: SESSION END

Works as expected :-)

Hope to hear from you soon,
Dmitry




____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null