[hylafax-users] Rockwell AC/K56 Flow control problem?

[Sander <sanhi@dds.nl>]

Hello HylaFax users,

I cant send or receive faxes correctly. In all the tries i did , it only
sends or receives a few lines. (Chopped of) most of the time after 1 cm
or so..
Strange in the log as you can see i only receive badlines..

I was thinking of a flowcontrol problem but i tried settings:

Class I or Class II

ModemRate:    38400 or 19200
ModemFlowControl: rtscts or xonxoff

ModemRecvFillOrder:    MSB2LSB or vice versa
Class2RecvFillTrigger:    "\022" or "\021"

but no succes...

What else could i try? or whats the problem here?

I'm running Suse 6.4 kernel 2.2.16 using HylaFax 4.1beta2 (RPM version
4.1beta2-135) and libtiff 3.4  I installed the Suse update of Hylafax.

The modem is Dynalink V1456E-R2 (Rockwell)

How to get this working? But if there are people who read this using a
similar rockwell modem, and they have a workinf Conf file i'd really
like to see it.

Thanks in advance,

Sander

/var/log/messages:
Aug 17 12:46:03 indigo FaxGetty[981]: MODEM ROCKWELL
AC/K56/V2.210-V90_2M_DLS

logfile:

Aug 17 11:49:58.53: [11971]: <-- [4:ATA\r]
Aug 17 11:50:07.12: [11971]: --> [5:+FCON]
Aug 17 11:50:07.12: [11971]: ANSWER: FAX CONNECTION
Aug 17 11:50:07.12: [11971]: RECV FAX: begin
Aug 17 11:50:08.73: [11971]: --> [29:+FTSI: "                    "]
Aug 17 11:50:08.73: [11971]: REMOTE TSI ""
Aug 17 11:50:09.15: [11971]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Aug 17 11:50:09.15: [11971]: REMOTE wants 9600 bit/s
Aug 17 11:50:09.15: [11971]: REMOTE wants page width 1728 pixels in 215
mm
Aug 17 11:50:09.15: [11971]: REMOTE wants unlimited page length
Aug 17 11:50:09.15: [11971]: REMOTE wants 3.85 line/mm
Aug 17 11:50:09.15: [11971]: REMOTE wants 1-D MR
Aug 17 11:50:09.15: [11971]: --> [2:OK]
Aug 17 11:50:09.16: [11971]: <-- [7:AT+FDR\r]
Aug 17 11:50:10.77: [11971]: --> [5:+FCFR]
Aug 17 11:50:13.02: [11971]: --> [22:+FDCS: 0,3,0,2,0,0,0,3]
Aug 17 11:50:13.02: [11971]: REMOTE wants 9600 bit/s
Aug 17 11:50:13.02: [11971]: REMOTE wants page width 1728 pixels in 215
mm
Aug 17 11:50:13.02: [11971]: REMOTE wants unlimited page length
Aug 17 11:50:13.02: [11971]: REMOTE wants 3.85 line/mm
Aug 17 11:50:13.03: [11971]: REMOTE wants 1-D MR
Aug 17 11:50:13.03: [11971]: --> [7:CONNECT]
Aug 17 11:50:13.03: [11971]: RECV: begin page
Aug 17 11:50:13.03: [11971]: RECV: send trigger 022
Aug 17 11:50:13.03: [11971]: <-- data [1]
Aug 17 11:50:20.02: [11971]: RECV: 12 total lines, 12 bad lines, 0
consecutive bad lines
Aug 17 11:50:20.02: [11971]: --> [17:+FPTS: 1,2219,0,0]
Aug 17 11:50:21.28: [11971]: --> [7:+FET: 2]
Aug 17 11:50:21.28: [11971]: RECV recv EOP (no more pages or documents)
Aug 17 11:50:21.39: [11971]: --> [2:OK]
Aug 17 11:50:21.39: [11971]: RECV: REJECT page quality, 0% good lines
(95% required)
Aug 17 11:50:21.39: [11971]: RECV send RTN (retrain negative)
Aug 17 11:50:21.39: [11971]: <-- [10:AT+FPTS=2\r]
Aug 17 11:50:21.51: [11971]: --> [2:OK]
Aug 17 11:50:21.51: [11971]: <-- [7:AT+FDR\r]
Aug 17 11:50:24.22: [11971]: --> [8:+FHNG: 0]
Aug 17 11:50:24.22: [11971]: REMOTE HANGUP: Normal and proper end of
connection (code 0)
Aug 17 11:50:24.23: [11971]: RECV FAX (00000045): recvq/fax00037.tif
from , route to <unspecified>, 0 pages in 0:17
Aug 17 11:50:24.23: [11971]: RECV FAX: Normal and proper end of
connection
Aug 17 11:50:24.23: [11971]: RECV FAX (00000045): session with
terminated abnormally: Normal and proper end of connection
Aug 17 11:50:24.23: [11971]: RECV FAX: bin/faxrcvd "recvq/fax00037.tif"
"ttyS1" "00000045" "Normal and proper end of connection"
Aug 17 11:50:24.31: [11971]: RECV FAX: end
Aug 17 11:50:24.31: [11971]: SESSION END

config.ttyS0
#
ModemType:  Class2  # use class 2 interface
ModemRate:  19200
ModemFlowControl: rtscts  # default
ModemWaitForConnect: yes
#
ModemResetCmds:  AT&F
ModemNoFlowCmd:  AT&K
ModemHardFlowCmd: AT&K3  # hardware flow control cmd
ModemSoftFlowCmd: AT&K4  # software flow control cmd
ModemSetupDTRCmd: AT&D2  # DTR off causes modem to reset
ModemSetupDCDCmd: AT&C2  # DCD follows carrier
ModemSetupAACmd: AT+FAA=1+FCLASS=0 # enable in current class
#
ModemSendFillOrder: LSB2MSB  # as expected
ModemRecvFillOrder: MSB2LSB  # opposite of what makes sense
Class2RecvDataTrigger: "\022"



____________________ HylaFAX(tm) Users Mailing List _______________________
 To unsub: mail -s unsubscribe hylafax-users-request@hylafax.org < /dev/null