RE: flexfax: I need to choose a fax modem

[Tim Rice <tim@trr.metro.net>]

On Sun, 21 May 2000, Kirk Bocek wrote:

> Tim,
> You gave some great help with my MultiTech 3334. Could you repost your
> config file you use for the 2834?
> 
> Thanks.
-----------< cut >---------------
# $Id: mt-1432,v 1.23 1996/06/24 02:58:36 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Multi-Tech MT1432, MT224BA, and MT1932ZDX modems.
#
# MT1432	firmware rev 0307 I or newer
# MT132BG	rev 0109A
# MT1932ZDX	rev 0109H
#
# Note that MT1432 modems come in several varieties:
#
# MT1432BA	uses Rockwell data pump
# MT1432BA/A	uses AT&T data pump
# MT1432BG	MT1432BA tweaked for German FCC
# MT1432MK	(for UK?)
#
# The modem has been tried with both XON/XOFF and RTS/CTS flow
# control; this configuration is for hardware flow control.
#
#
CountryCode:		1
AreaCode:		707
FAXNumber:		+1.999.999.9999
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	"etc/dialrules"
ServerTracing:		11
SessionTracing:		11
#ServerTracing:		0x0000f
#SessionTracing:		0x0003f
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		off
GettyArgs:		"-t 60 -h %l dx_%s"
LocalIdentifier:	"+1.999.999.9999"
LogFacility:		local1
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400		# lock rate for DCE-DTE communication
ModemFlowControl:	rtscts		# default
#
ModemHardFlowCmd:	AT&E4		# hardware flow control
ModemSoftFlowCmd:	AT&E5		# software flow control
ModemSetupDTRCmd:	AT&D3		# setup so DTR drop resets modem
ModemSetupDCDCmd:	AT&C4		# setup so DCD resets modem on
					# carrier drop
ModemSetupAACmd:	AT+FAA=1	# enable adaptive-answer in class 2
#
# NB: some models get confused by the @
#
ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
Class2RecvDataTrigger:	"\022"		# character sent to modem to start recv
Class2XmitWaitForXON:	no
#
Class2APQueryCmd:	""		# AT+FAP=? not supported on this modem
Class2NFLOCmd:		AT+FLO=0	# Class 2: no flow control
Class2SFLOCmd:		AT+FLO=1	# Class 2: software flow control
Class2HFLOCmd:		AT+FLO=2	# Class 2: hardware flow control
-----------< end cut >---------------
[snip]
> 

-- 
Tim Rice				Multitalents	(707) 874-1130
tim@trr.metro.net