Re: flexfax: 5600ZDX Config file help

[Glenn Burkhardt <glenn@aoi.ultranet.com>]

Looks like the firmware rev has changed, and you have an "improved" model.
My version is V2.100-V90_2M_DLS (ati3).

You didn't mention if transmission is OK.  For the record, is it?

But probably the problem is the absence of this command in your config file:

ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense

This command is in the config file I use that works for me with receive
(see attached), and is in the rockwell-k56.config file I recently pulled 
from the web site.

The log file indicates that all the handshaking is working, and the modem
thinks that the session went without problems.  But no data was transferred!
You might want to try using a different fax machine to send the info.  I like
to use one of the fax back services for testing.  If you can get it to work
with some fax machines but not others, it makes a good case for Multitech
tech support.

But try the other config files first....

# rockwell-k56.config modem configuration patch
#
# Configuration for a Rockwell AC/K56-based Class 2 modem.
# based upon work of Mark J. Bailey, Jonathan Mau and Glenn Burkhardt.
#    Multitech MT5600ZDX
#    Diamond Multimedia SupraExpress 56e PRO
#    Zoom Telephonics 56Kx - to be added
# (and others)
#
# Instructions: install file as /var/spool/fax/config/rockwell-k56
#       delete/rename your config.ttySx file and rerun faxaddmodem.
#

# This configuration file sets up the modem to run at 38.4 for
# sending and for receiving.  XON/XOFF is used for flow control
# which also works for data connections.  Adaptive answer support
# is reliable, but to use it you must also enable ModemWaitForConnect
# to force the server to skip intermediate status messages and
# wait for the "CONNECT" message.
#
# CONFIG: CLASS2: Rockwell-MultiModemZDXV-*
# CONFIG: CLASS2: ROCKWELL-AC/K56-*
#
# BEGIN-SERVER
# END-SERVER
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use class 2 interface
ModemRate:		38400
ModemFlowControl:	xonxoff		# default
ModemWaitForConnect:	yes		# wait for CONNECT on answer
#
#ModemResetCmds:	AT&F2		# what you want for a Supra
ModemNoFlowCmd:		AT&K		# disable flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FCLASS=0;+FAA=1 # enable in class 0
#
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
Class2RecvDataTrigger:	"\022"		# a la 2388-B
# $Id: class2,v 1.2 1999/01/10 09:09:37 robert Exp $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Generic Class 2 modem configuration.
#
# EDIT THIS CONFIGURATION TO REFLECT YOUR SETUP
#
CountryCode:		1
AreaCode:		978
FAXNumber:		+1.978.453.5731
LongDistancePrefix:	1
InternationalPrefix:	011
DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		0x39
RecvFileMode:		0644
LogFileMode:		0644
DeviceMode:		0600
RingsBeforeAnswer:	1
SpeakerVolume:		Off
GettyArgs:		"-h -t 20 %l F%s xterm"
LocalIdentifier:	"Focus AOI, Inc."
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		50
UUCPLockTimeout:	5
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:		Class2		# use this to supply a hint
ModemRate:		115200		# max rate for DCE-DTE communication
ModemFlowControl:	xonxoff	
ModemSetupDTRCmd:	AT&D3		# setup so DTR drop resets modem
#ModemSetupDCDCmd:	AT&C1		# setup so DCD reflects carrier (or not)
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd:		ATDT%s@		# T for tone dialing, @ for silence
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemSetupAACmd: AT+FAA=1+FCLASS=0	# leave in data class for answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
#
# Configuration parameters for Class 2 modems.
#
Class2RELCmd:		AT+FREL=1	# byte-align EOL codes on recv
Class2CQCmd:		""		# commands to enable copy quality proc.
Class2DDISCmd:		""		# disable pre-dial DIS command hack
Class2PTSCmd:		AT+FPTS		# set post-page status command
Class2SPLCmd:		AT+FSPL		# set polling indicator command
#
# If Class2RecvDataTrigger is not set, then it is set to DC1
#
Class2RecvDataTrigger:	""		# character sent to modem to start recv
Class2XmitWaitForXON:	yes		# if true, wait for XON before send