flexfax: session is terminated abnormally During fax recieving.

[frank gelbrich <61532313@3web.net>]

Hello
I have SuSE6.2   & HylaFax4.0.  USR
56K Fax Modem.
I have trouble receiving multiplied faxes, the session
will be terminated before all the faxes are received.
Here is copy of my massages what I get & the modem.config
file.
Can anyone help?

Thanks Frank
 

Jan 12 19:44:03 earth FaxGetty[226]: RECV FAX (00000040): from Acer America, page 1 in 0:17, INF, 7.7 line/mm, 1-D MR
Jan 12 19:44:03 earth FaxGetty[226]: RECV FAX (00000040): recvq/fax00046.tif from Acer America, route to <unspecified>, 1 pages in 0:19
Jan 12 19:44:15 earth kernel: Creative SBLive! at 0xd000 on irq 10
Jan 12 19:44:27 earth modprobe: modprobe: Can't locate module char-major-15
Jan 12 19:44:27 earth modprobe: modprobe: Can't locate module char-major-15
Jan 12 19:44:48 earth FaxGetty[226]: RECV FAX (00000040): from Acer America, page 1 in 0:45, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:07 earth FaxGetty[226]: RECV FAX (00000040): from Acer America, page 2 in 0:19, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:31 earth FaxGetty[226]: RECV FAX (00000040): from Acer America, page 3 in 0:24, INF, 3.85 line/mm, 1-D MR
Jan 12 19:45:49 earth FaxGetty[226]: RECV FAX (00000040): recvq/fax00047.tif from Acer America, route to <unspecified>, 3 pages in 1:46
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX: bin/faxrcvd "recvq/fax00046.tif" "modem" "00000040" ""
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX (00000040): session with Acer America terminated abnormally: Unspecified Phase C error, including too much delay between TCF and +FDR command
Jan 12 19:45:50 earth FaxGetty[226]: RECV FAX: bin/faxrcvd "recvq/fax00047.tif" "modem" "00000040" "Unspecified Phase C error, including too much delay between TCF and +FDR command"
 

CountryCode:               1
AreaCode:                    780
FAXNumber:                +1.780.488.xxx
LongDistancePrefix:      1
InternationalPrefix:        011
DialStringRules:           etc/dialrules
ServerTracing:             1
SessionTracing:          11
RecvFileMode:            0644
LogFileMode:              0600
DeviceMode:               0600
RingsBeforeAnswer:      1
SpeakerVolume:           on
GettyArgs:                   "-h %l dx_%s"
LocalIdentifier:              "gelly"
TagLineFont:                 etc/lutRS18.pcf
TagLineFormat:            "From %%l|%c|Page %%p of %%t"
QualifyTSI:                   ""
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2.0        # use this to supply a hint
ModemRate:              38400
ModemFlowControl:       rtscts
ModemSetupDTRCmd:       ATS13=1&D2      # setup so DTR drop resets modem
ModemSetupDCDCmd:       AT&C1           # setup so DCD reflects carrier (or not)
Class2RecvDataTrigger:  "\022"
#
# We normally append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer.  This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
#     put it in the ModemDialCmd; e.g. "DT9%s@".
#
ModemDialCmd:           ATDT%s          # T for tone dialing
#
# Other possible configuration stuff.  The default strings are
# shown below.  Only those that are different from the defaults
# need to be included in the configuration file.
#
ModemResetCmds:         ""              # stuff to do when modem is reset
ModemAnswerCmd:         ATA             # use this to answer phone
ModemNoAutoAnswerCmd:   ATS0=0          # disable auto-answer
ModemNoFlowCmd:         AT&H0&I0&R1
ModemHardFlowCmd:       AT&H1&I0&R2
ModemSoftFlowCmd:       AT&H2&I2&R1
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
ModemSetVolumeCmd:      "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
ModemEchoOffCmd:        ATE0            # disable command echo
ModemVerboseResultsCmd: ATV1            # enable verbose command results
ModemResultCodesCmd:    ATQ0X4
ModemOnHookCmd:         ATH0            # place phone on hook (hangup)
ModemSoftResetCmd:      ATZ             # do soft reset of modem
ModemWaitTimeCmd:       ATS7=60         # wait 60 seconds for carrier
ModemCommaPauseTimeCmd: ATS8=2          # comma pause time is 2 seconds
ModemRecvFillOrder:     LSB2MSB         # bit order of received facsimile
ModemSendFillOrder:     LSB2MSB         # bit order modem expects for transmit
#
# Configuration parameters for Class 2.0 modems.
#
Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0
Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)
Class2CQCmd:            ""              # commands to enable copy quality proc.
Class2AbortCmd:         AT+FKS          # abort session command
Class2CQQueryCmd:       !(0),(0)        # query for copy quality capabilities
Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities
Class2TBCCmd:           AT+FPP=0        # setup stream mode
Class2CRCmd:            AT+FCR=1        # enable capability to receive
Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter
Class2BUGCmd:           AT+FBU=0        # enable HDLC frame tracing
Class2LIDCmd:           AT+FLI          # set local identifier command
Class2DCCCmd:           AT+FCC          # set modem capabilities command
Class2DISCmd:           AT+FIS          # set session parameters command
Class2DDISCmd:          ""              # disable pre-dial DIS command hack
Class2CIGCmd:           AT+FPI          # set polling identifier command
Class2NRCmd:            AT+FNR=1,1,1,0  # setup status reporting command
Class2PIECmd:           ""
Class2PTSCmd:           AT+FPS          # set post-page status command
Class2SPLCmd:           AT+FSP          # set polling indicator command
Class2NFLOCmd:          AT+FLO=0        # set no flow control command
Class2SFLOCmd:          AT+FLO=1        # set software flow control command
Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command