flexfax: HylaFAX cannot receive multiple pages

[DAVID ARNOLD <david@cadetshoes.com.au>]

Same old same old.  Bet I solve this one within the next couple 
of hours ;)

Cannot receive multiple page faxes.  I know about the retrain 
problems but the logs look fine.  But when viewing the received 
fax with xv/gimp there is only one page.  The file size between
the same page sent once and twice is what it should be...

And Does anyone know why the number rings out when I dial?  I have 
to cancel when it dials, then redial it.  That works everytime.

Hylafax-v4.02pl2, Netcomm Roadster II class 2, linux 2.2.9, sending
from a canon-410 (only fax tried)

Nov 04 11:37:36.14: [21896]: SESSION BEGIN 00000462 610399999999
Nov 04 11:37:36.14: [21896]: <-- [4:ATA\r]
Nov 04 11:37:37.49: [21896]: --> [3:FAX]
Nov 04 11:37:37.49: [21896]: ANSWER: FAX CONNECTION
Nov 04 11:37:37.50: [21896]: RECV FAX: begin
Nov 04 11:37:44.91: [21896]: --> [5:	��M�]
Nov 04 11:37:44.91: [21896]: --> [29:+FTSI: "       613 9999 9999"]
Nov 04 11:37:44.91: [21896]: REMOTE TSI "613 9999 9999"
Nov 04 11:37:45.27: [21896]: --> [22:+FDCS: 0,3,0,2,0,0,0,0]
Nov 04 11:37:45.27: [21896]: REMOTE wants 9600 bit/s
Nov 04 11:37:45.27: [21896]: REMOTE wants page width 1728 pixels in 215 mm
Nov 04 11:37:45.27: [21896]: REMOTE wants unlimited page length 
Nov 04 11:37:45.27: [21896]: REMOTE wants 3.85 line/mm
Nov 04 11:37:45.27: [21896]: REMOTE wants 1-D MR
Nov 04 11:37:45.38: [21896]: --> [2:OK]
Nov 04 11:37:45.38: [21896]: <-- [7:AT+FDR\r]
Nov 04 11:37:46.92: [21896]: --> [5:+FCFR]
Nov 04 11:37:49.21: [21896]: --> [22:+FDCS: 0,3,0,2,0,0,0,0]
Nov 04 11:37:49.21: [21896]: REMOTE wants 9600 bit/s
Nov 04 11:37:49.21: [21896]: REMOTE wants page width 1728 pixels in 215 mm
Nov 04 11:37:49.21: [21896]: REMOTE wants unlimited page length 
Nov 04 11:37:49.21: [21896]: REMOTE wants 3.85 line/mm
Nov 04 11:37:49.21: [21896]: REMOTE wants 1-D MR
Nov 04 11:37:49.21: [21896]: --> [7:CONNECT]
Nov 04 11:37:49.21: [21896]: RECV: begin page
Nov 04 11:37:49.21: [21896]: RECV: send trigger 022
Nov 04 11:37:49.21: [21896]: <-- data [1]
Nov 04 11:38:10.03: [21896]: RECV: 1196 total lines, 0 bad lines, 0 consecutive bad lines
Nov 04 11:38:10.03: [21896]: --> [17:+FPTS: 1,2219,0,0]
Nov 04 11:38:11.31: [21896]: --> [7:+FET: 0]
Nov 04 11:38:11.31: [21896]: RECV recv MPS (more pages, same document)
Nov 04 11:38:11.42: [21896]: --> [2:OK]
Nov 04 11:38:11.42: [21896]: RECV send MCF (message confirmation)
Nov 04 11:38:11.42: [21896]: RECV FAX (00000462): from 613 9999 9999, page 1 in 0:26, INF, 3.85 line/mm, 1-D MR
Nov 04 11:38:11.42: [21896]: <-- [7:AT+FDR\r]
Nov 04 11:38:15.40: [21896]: --> [7:CONNECT]
Nov 04 11:38:15.40: [21896]: RECV: begin page
Nov 04 11:38:15.40: [21896]: RECV: send trigger 022
Nov 04 11:38:15.40: [21896]: <-- data [1]
Nov 04 11:38:38.50: [21896]: RECV: 1160 total lines, 0 bad lines, 0 consecutive bad lines
Nov 04 11:38:38.61: [21896]: --> [17:+FPTS: 1,2219,0,0]
Nov 04 11:38:39.89: [21896]: --> [7:+FET: 2]
Nov 04 11:38:39.89: [21896]: RECV recv EOP (no more pages or documents)
Nov 04 11:38:40.00: [21896]: --> [2:OK]
Nov 04 11:38:40.00: [21896]: RECV send MCF (message confirmation)
Nov 04 11:38:40.00: [21896]: RECV FAX (00000462): from 613 9999 9999, page 2 in 0:29, INF, 3.85 line/mm, 1-D MR
Nov 04 11:38:40.01: [21896]: RECV FAX (00000462): recvq/fax00054.tif from 613 9999 9999, route to <unspecified>, 2 pages in 1:03
Nov 04 11:38:40.01: [21896]: <-- [7:AT+FDR\r]
Nov 04 11:38:42.90: [21896]: --> [8:+FHNG: 0]
Nov 04 11:38:42.90: [21896]: REMOTE HANGUP: Normal and proper end of connection (code 0)
Nov 04 11:38:42.90: [21896]: RECV FAX: bin/faxrcvd "recvq/fax00054.tif" "ttyE7" "00000462" ""
Nov 04 11:38:43.14: [21896]: RECV FAX: end
Nov 04 11:38:43.14: [21896]: SESSION END

DialStringRules:	etc/dialrules
ServerTracing:		1
SessionTracing:		11
RecvFileMode:		0600
LogFileMode:		0600
DeviceMode:		0600
RingsBeforeAnswer:	1
GettyArgs:		"-r -b -s 115200 -x 4"
TagLineFont:		etc/lutRS18.pcf
TagLineFormat:		"From %%l|%c|Page %%p of %%t"
MaxRecvPages:		25

ModemDialCmd:		ATDT0%s
ModemWaitTimeCmd:	ATS7=1000
ModemType:		Class2		# use class 2 interface
ModemRate:		38400
ModemFlowControl:	rtscts		# default
ModemNoFlowCmd:		AT&K		# disable flow control cmd
ModemHardFlowCmd:	AT&K3		# hardware flow control cmd
ModemSoftFlowCmd:	AT&K4		# software flow control cmd
ModemSetupDTRCmd:	AT&D3		# DTR off causes modem to reset
ModemSetupDCDCmd:	AT&C1		# DCD follows carrier
ModemSetupAACmd:	AT+FAA=1+FCLASS=0 # enable in current class
ModemSendFillOrder:	LSB2MSB		# as expected
ModemRecvFillOrder:	MSB2LSB		# opposite of what makes sense
ModemAnswerFaxBeginCmd:	"<19200>"	# modem switches on fax receive
Class2RecvDataTrigger:	"\022"