flexfax: HylaFax doesnt send

[SysAdmin <SysAdmin.ITKOEL01@RegTP.de>]

Hi!

I have SUSE Linux 6.2 Distribution and HylaFAX server running with a
Hayes Optima 288
Class1 modem. Receiving works fine but when I try to send something it
doesn�t
work. It connects and two seconds later it disconnects without doing
anything.
No error message and the Fax queue is empty.
Maybe you can help me. These are the log entries:

Oct 11 15:47:26.33: [  911]: SESSION BEGIN 00000069 49221181
Oct 11 15:47:26.33: [  911]: SEND FAX: JOB 67 DEST 181 COMMID 00000069
Oct 11 15:47:26.33: [  911]: MODEM set DTR OFF
Oct 11 15:47:26.33: [  911]: DELAY 2600 ms
Oct 11 15:47:28.93: [  911]: MODEM set DTR ON
Oct 11 15:47:28.93: [  911]: MODEM set baud rate: 19200 baud, input flow
XON/XOFF, output flow XON/XOFF
Oct 11 15:47:28.93: [  911]: MODEM flush i/o
Oct 11 15:47:28.93: [  911]: <-- [15:ATE0V1Q0S0=0H0\r]
Oct 11 15:47:29.18: [  911]: --> [2:OK]
Oct 11 15:47:29.18: [  911]: <-- [21:ATS8=2S7=80&K4&D2&C1\r]
Oct 11 15:47:29.44: [  911]: --> [2:OK]
Oct 11 15:47:29.44: [  911]: <-- [12:AT+FCLASS=1\r]
Oct 11 15:47:29.63: [  911]: --> [2:OK]
Oct 11 15:47:29.63: [  911]: <-- [7:ATL3M1\r]
Oct 11 15:47:29.82: [  911]: --> [2:OK]
Oct 11 15:47:29.82: [  911]: MODEM input buffering enabled
Oct 11 15:47:29.82: [  911]: <-- [12:AT+FCLASS=1\r]
Oct 11 15:47:30.11: [  911]: --> [2:OK]
Oct 11 15:47:30.11: [  911]: MODEM set XON/XOFF/FLUSH: input ignored,
output disabled
Oct 11 15:47:30.11: [  911]: DIAL 181
Oct 11 15:47:30.11: [  911]: <-- [10:ATX3DT181\r]
Oct 11 15:47:49.46: [  911]: --> [7:CONNECT]
Oct 11 15:47:49.46: [  911]: MODEM input buffering disabled
Oct 11 15:47:51.47: [  911]: --> [2:OK]
Oct 11 15:47:51.47: [  911]: <-- [9:AT+FRH=3\r]
Oct 11 15:47:51.52: [  911]: --> [7:CONNECT]
Oct 11 15:47:52.18: [  911]: --> [2:OK]
Oct 11 15:47:52.18: [  911]: REMOTE CSI "49 221 94478181"
Oct 11 15:47:52.18: [  911]: <-- [9:AT+FRH=3\r]
Oct 11 15:47:52.23: [  911]: --> [7:CONNECT]
Oct 11 15:47:52.57: [  911]: --> [2:OK]
Oct 11 15:47:52.57: [  911]: REMOTE best rate 9600 bit/s
Oct 11 15:47:52.57: [  911]: REMOTE max page width 1728 pixels in 215 mm
Oct 11 15:47:52.57: [  911]: REMOTE max unlimited page length
Oct 11 15:47:52.57: [  911]: REMOTE best vres 7.7 line/mm
Oct 11 15:47:52.57: [  911]: REMOTE best format 2-D MMR
Oct 11 15:47:52.57: [  911]: REMOTE supports T.30 Annex A, ECM
Oct 11 15:47:52.57: [  911]: REMOTE best 20 ms/scanline
Oct 11 15:47:52.57: [  911]: USE 9600 bit/s
Oct 11 15:47:52.57: [  911]: USE 20 ms/scanline
Oct 11 15:47:52.57: [  911]: <-- [9:AT+FTH=3\r]
Oct 11 15:47:52.85: [  911]: --> [7:CONNECT]
Oct 11 15:47:52.85: [  911]: <-- data [3]
Oct 11 15:47:52.85: [  911]: <-- data [2]
Oct 11 15:47:54.20: [  911]: --> [2:OK]
Oct 11 15:47:54.20: [  911]: MODEM input buffering enabled
Oct 11 15:47:54.20: [  911]: <-- [5:ATH0\r]
Oct 11 15:47:54.38: [  911]: --> [2:OK]
Oct 11 15:47:54.38: [  911]: MODEM set DTR OFF
Oct 11 15:47:54.38: [  911]: SESSION END


Any ideas?

Thanks in advance.

Gerhard Schirwon, Germany